Chrysler 300/300 Touring/300C, Dodge Magnum. Manual - part 2337

 

  Index      Chrysler     Chrysler 300/300 Touring/300C, Dodge Magnum - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  2335  2336  2337  2338   ..

 

 

Chrysler 300/300 Touring/300C, Dodge Magnum. Manual - part 2337

 

 

8. Install the carpet onto the front floor panel and under the instrument panel (Refer to 23 - BODY/INTERIOR/

CARPETS AND FLOOR MATS - INSTALLATION).

9. Install the front seats (Refer to 23 - BODY/SEATS/SEAT - INSTALLATION).

10. Install the center floor console (Refer to 23 - BODY/INTERIOR/FLOOR CONSOLE - INSTALLATION).

24 - 382

DISTRIBUTION

LX

DUCT-INSTRUMENT PANEL

REMOVAL

WARNING: On vehicles equipped with airbags, disable the airbag system before attempting any steering
wheel, steering column, or instrument panel component diagnosis or service. Disconnect and isolate the
battery negative (ground) cable, then wait two minutes for the airbag system capacitor to discharge before
performing further diagnosis or service. This is the only sure way to disable the airbag system. Failure to
take the proper precautions could result in accidental airbag deployment and possible personal injury or
death.

NOTE: Take the proper precautions to protect the front face of the instrument panel from cosmetic damage.

NOTE: LHD model shown. RHD model similar.

1. Remove the instrument panel and place it on a

workbench (Refer to 23 - BODY/INSTRUMENT
PANEL/INSTRUMENT

PANEL

ASSEMBLY

-

REMOVAL).

2. Remove the screw that secures the instrument

panel top pad (1) to the reinforcement bracket (2).

3. Remove the four screws that secure the driver side

instrument panel duct and demister duct assembly
(3) to the instrument panel and remove the duct
assembly.

4. Remove the four screws that secure the passenger

side instrument panel duct and demister duct
assembly (4) to the instrument panel and remove
the duct assembly.

INSTALLATION

NOTE: LHD model shown. RHD model similar.

1. Position the passenger side instrument panel duct

and demister duct assembly (4) into the instrument
panel.

2. Install the passenger side instrument panel duct

and demister duct assembly onto the outlets of the
instrument panel. Make sure that the ducts are cor-
rectly installed over the instrument panel and
demister outlet seals.

3. Install the four screws that secure the passenger

side instrument panel duct and demister duct
assembly to the instrument panel. Tighten the
screws to 2.2 N·m (20 in. lbs.).

4. Position the driver side instrument panel duct and

demister duct assembly (3) into the instrument
panel.

5. Install the driver side instrument panel duct and

demister duct assembly onto the outlets of the instrument panel. Make sure that the ducts are correctly installed
over the instrument panel and demister outlet seals.

6. Install the four screws that secure the driver side instrument panel duct and demister duct assembly to the instru-

ment panel. Tighten the screws to 2.2 N·m (20 in. lbs.).

LX

DISTRIBUTION

24 - 383

7. Install the screw that secures the instrument panel top pad (1) to the reinforcement bracket (2). Tighten the

screw to 2.2 N·m (20 in. lbs.).

8. Install the instrument panel (Refer to 23 - BODY/INSTRUMENT PANEL/INSTRUMENT PANEL ASSEMBLY -

INSTALLATION).

24 - 384

DISTRIBUTION

LX

DUCT-INSTRUMENT PANEL DEMISTER

REMOVAL

WARNING: On vehicles equipped with airbags, disable the airbag system before attempting any steering
wheel, steering column, or instrument panel component diagnosis or service. Disconnect and isolate the
battery negative (ground) cable, then wait two minutes for the airbag system capacitor to discharge before
performing further diagnosis or service. This is the only sure way to disable the airbag system. Failure to
take the proper precautions could result in accidental airbag deployment and possible personal injury or
death.

NOTE: Take the proper precautions to protect the front face of the instrument panel from cosmetic damage.

NOTE: LHD model shown. RHD model similar.

1. Remove the instrument panel and place it on a

workbench (Refer to 23 - BODY/INSTRUMENT
PANEL/INSTRUMENT

PANEL

ASSEMBLY

-

REMOVAL).

2. Remove the screw that secures the instrument

panel top pad (1) to the reinforcement bracket (2).

3. Remove the four screws that secure the driver side

instrument panel duct and demister duct assembly
(3) to the instrument panel and remove the duct
assembly.

4. Remove the four screws that secure the passenger

side instrument panel duct and demister duct
assembly (4) to the instrument panel and remove
the duct assembly.

INSTALLATION

NOTE: LHD model shown. RHD model similar.

1. Position the passenger side instrument panel duct

and demister duct assembly (4) into the instrument
panel.

2. Install the passenger side instrument panel duct

and demister duct assembly onto the outlets of the
instrument panel. Make sure that the ducts are cor-
rectly installed over the instrument panel and
demister outlet seals.

3. Install the four screws that secure the passenger

side instrument panel duct and demister duct
assembly to the instrument panel. Tighten the
screws to 2.2 N·m (20 in. lbs.).

4. Position the driver side instrument panel duct and

demister duct assembly (3) into the instrument
panel.

5. Install the driver side instrument panel duct and

demister duct assembly onto the outlets of the instrument panel. Make sure that the ducts are correctly installed
over the instrument panel and demister outlet seals.

6. Install the four screws that secure the driver side instrument panel duct and demister duct assembly to the instru-

ment panel. Tighten the screws to 2.2 N·m (20 in. lbs.).

LX

DISTRIBUTION

24 - 385

 

 

 

 

 

 

 

Content   ..  2335  2336  2337  2338   ..