Chrysler 300/300 Touring/300C, Dodge Magnum. Manual - part 2314

 

  Index      Chrysler     Chrysler 300/300 Touring/300C, Dodge Magnum - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  2312  2313  2314  2315   ..

 

 

Chrysler 300/300 Touring/300C, Dodge Magnum. Manual - part 2314

 

 

When Monitored:
With the ignition on.

Set Condition:
If the Right Sunload Sensor input is out of range toward the high voltage threshold.

Possible Causes

(G139) SUN SENSOR NO. 2 SIGNAL CIRCUIT OPEN

(G139) SUN SENSOR NO. 2 SIGNAL CIRCUIT SHORTED TO VOLTAGE

(G939) SUN SENSOR RETURN CIRCUIT OPEN

SUN SENSOR

A/C HEATER CONTROL

NOTE: This DTC must be active for the results of this test to be valid. Do not perform this test if this DTC
is stored. Refer to HVAC System Test (ATC) for stored DTC test procedures.

Diagnostic Test

1.

CHECK (G139) SUN SENSOR NO. 2 SIGNAL CIRCUIT VOLTAGE

Turn the ignition off.

Disconnect the Sun Sensor harness connector.

Turn the ignition on.

Measure the voltage of the (G139) Sun Sensor No. 2 Signal circuit.

What voltage is present?

Above 5.2 Volts

Go To 2

4.8 Volts to 5.2 Volts

Go To 3

Below 4.8 Volts

Go To 5

2.

CHECK (G139) SUN SENSOR NO. 2 SIGNAL CIRCUIT FOR A SHORT TO VOLTAGE

Turn the ignition off.

Disconnect the A/C Heater Control C1 harness connector.

Turn the ignition on.

Measure the voltage of the (G139) Sun Sensor No. 2 Signal circuit.

Is the voltage above 0.2 volts?

Yes

>> Repair the (G139) Sun Sensor No. 2 Signal circuit for a

short to voltage.

Perform BODY VERIFICATION TEST – VER 1. (Refer to 8
-

ELECTRICAL/ELECTRONIC

CONTROL

MODULES/

FRONT CONTROL MODULE - DIAGNOSIS AND TEST-
ING).

No

>> Replace the A/C Heater Control in accordance with the Ser-

vice Information.

Perform BODY VERIFICATION TEST – VER 1. (Refer to 8
-

ELECTRICAL/ELECTRONIC

CONTROL

MODULES/

FRONT CONTROL MODULE - DIAGNOSIS AND TEST-

24 - 290

HVAC - ELECTRICAL DIAGNOSTICS

LX

ING).

3.

CHECK (G939) SUN SENSOR RETURN CIRCUIT FUNCTION

Turn the ignition off.

Connect a jumper wire between the (G139) Sun Sensor No. 2 Signal
circuit and the (G939) Sun Sensor Return circuit in the Sun Sensor har-
ness connector.

Turn the ignition on.

With the scan tool in HVAC, select Data Display and read the Right
Solar Sensor voltage.

Is the voltage below 0.2 volts?

Yes

>> Replace the Sun Sensor in accordance with the Service

Information.

Perform BODY VERIFICATION TEST – VER 1. (Refer to 8
-

ELECTRICAL/ELECTRONIC

CONTROL

MODULES/

FRONT CONTROL MODULE - DIAGNOSIS AND TEST-
ING).

No

>> Go To 4

4.

CHECK (G939) SUN SENSOR RETURN CIRCUIT FOR AN OPEN

Turn the ignition off.

Disconnect the A/C Heater Control C1 harness connector.

Measure the resistance of the (G939) Sun Sensor Return circuit
between the Sun Sensor harness connector and the A/C Heater Control
C1 harness connector.

Is the resistance below 5.0 ohms?

Yes

>> Replace the A/C Heater Control in accordance with the Ser-

vice Information.

Perform BODY VERIFICATION TEST – VER 1. (Refer to 8
-

ELECTRICAL/ELECTRONIC

CONTROL

MODULES/

FRONT CONTROL MODULE - DIAGNOSIS AND TEST-
ING).

No

>> Repair the (G939) Sun Sensor Return circuit for an open.

Perform BODY VERIFICATION TEST – VER 1. (Refer to 8
-

ELECTRICAL/ELECTRONIC

CONTROL

MODULES/

FRONT CONTROL MODULE - DIAGNOSIS AND TEST-
ING).

LX

HVAC - ELECTRICAL DIAGNOSTICS

24 - 291

5.

CHECK (G139) SUN SENSOR NO. 2 SIGNAL CIRCUIT FOR AN OPEN

Turn the ignition off.

Disconnect the A/C Heater Control C1 harness connector.

Measure the resistance of the (G139) Sun Sensor No. 2 Signal circuit
between the Sun Sensor harness connector and the A/C Heater Control
C1 harness connector.

Is the resistance below 5.0 ohms?

Yes

>> Replace the A/C Heater Control in accordance with the Ser-

vice Information.

Perform BODY VERIFICATION TEST – VER 1. (Refer to 8
-

ELECTRICAL/ELECTRONIC

CONTROL

MODULES/

FRONT CONTROL MODULE - DIAGNOSIS AND TEST-
ING).

No

>> Repair the (G139) Sun Sensor No. 2 Signal circuit for an

open.

Perform BODY VERIFICATION TEST – VER 1. (Refer to 8
-

ELECTRICAL/ELECTRONIC

CONTROL

MODULES/

FRONT CONTROL MODULE - DIAGNOSIS AND TEST-
ING).

24 - 292

HVAC - ELECTRICAL DIAGNOSTICS

LX

B1610–AMBIENT LIGHT SENSOR INPUT CIRCUIT LOW (ATC)

For a complete wiring diagram Refer to Section 8W.

LX

HVAC - ELECTRICAL DIAGNOSTICS

24 - 293

 

 

 

 

 

 

 

Content   ..  2312  2313  2314  2315   ..