Chrysler 300/300 Touring/300C, Dodge Magnum. Manual - part 2292

 

  Index      Chrysler     Chrysler 300/300 Touring/300C, Dodge Magnum - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  2290  2291  2292  2293   ..

 

 

Chrysler 300/300 Touring/300C, Dodge Magnum. Manual - part 2292

 

 

B10B6–CABIN HEATER 1 CONTROL CIRCUIT OPEN (FCM)

For a complete wiring diagram Refer to Section 8W

24 - 202

HVAC - ELECTRICAL DIAGNOSTICS

LX

When Monitored:
With the ignition on, the ASD Relay energized, and the PTC No. 1 Relay command on.

Set Condition:
If the Front Control Module (FCM) detects that the (K360) PTC No. 1 Relay Control circuit is open.

Possible Causes

(K342) FUSED ASD RELAY OUTPUT CIRCUIT OPEN OR HIGH RESISTANCE

(K360) PTC NO. 1 RELAY CONTROL CIRCUIT SHORTED TO GROUND

(K360) PTC NO. 1 RELAY CONTROL CIRCUIT OPEN OR HIGH RESISTANCE

PTC NO. 1 RELAY

FRONT CONTROL MODULE (FCM)

Diagnostic Test

1.

VERIFY THAT THE DTC IS ACTIVE

WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A DIRECT LINE WITH THE FAN. DO NOT
PUT YOUR HANDS NEAR THE PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.

NOTE: If the FCM detects and stores a DTC, the FCM also stores the environmental conditions under which
the DTC was set.

NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may
assist when checking for an active DTC.
Turn the ignition on.

With the scan tool, erase FCM DTCs.

With the scan tool, actuate the PTC No. 1 Relay.

Monitor the scan tool for at least two minutes.

With the scan tool, read FCM DTCs.

Is the status Active for this DTC?

Yes

>> Go To 2

No

>> Check for an intermittent condition by inspecting the related wiring harness for chaffed, pierced,

pinched, and partially broken wires. Also, inspect the related connectors for broken, bent, pushed out,
spread, corroded, or contaminated terminals.

2.

CHECK (K342) FUSED ASD RELAY OUTPUT CIRCUIT FOR AN OPEN OR HIGH RESISTANCE

Turn the ignition off.

Remove the PTC No. 1 Relay.

Turn the ignition on.

Using a 12 volt test light connected to ground, check the (K342) Fused
ASD Relay Output circuit in the PTC No. 1 Relay connector.

NOTE: The test light should illuminate brightly. Compare the
brightness to that of a direct connection to the battery.

Does the test light illuminate brightly?

Yes

>> Go To 3

No

>> Repair the (K342) Fused ASD Relay Output circuit for an

open or high resistance.

Perform the BODY VERIFICATION TEST VER 1. (Refer to
8 - ELECTRICAL/ELECTRONIC CONTROL MODULES/
FRONT

CONTROL

MODULE

-

DIAGNOSIS

AND

TESTING).

LX

HVAC - ELECTRICAL DIAGNOSTICS

24 - 203

3.

CHECK (K360) PTC NO. 1 RELAY CONTROL CIRCUIT FOR A SHORT TO GROUND

Turn the ignition off.

Disconnect the FCM from the Power Module.

Measure the resistance between ground and the (K360) PTC No. 1
Relay Control circuit in the PTC No. 1 Relay connector.

Is the resistance above 10.0 ohms?

Yes

>> Go To 4

No

>> Repair the (K360) PTC No. 1 Relay Control circuit for a

short to ground.

Perform the BODY VERIFICATION TEST VER 1. (Refer to
8 - ELECTRICAL/ELECTRONIC CONTROL MODULES/
FRONT

CONTROL

MODULE

-

DIAGNOSIS

AND

TESTING).

4.

CHECK (K360) PTC NO. 1 RELAY CONTROL CIRCUIT FOR AN OPEN OR HIGH RESISTANCE

Measure the resistance of the (K360) PTC No. 1 Relay Control circuit
between the PTC No. 1 Relay connector and the FCM connector.

Is the resistance below 10.0 ohms?

Yes

>> Go To 5

No

>> Repair the (K360) PTC No. 1 Relay Control circuit for an

open or high resistance.

Perform the BODY VERIFICATION TEST VER 1. (Refer to
8 - ELECTRICAL/ELECTRONIC CONTROL MODULES/
FRONT

CONTROL

MODULE

-

DIAGNOSIS

AND

TESTING).

24 - 204

HVAC - ELECTRICAL DIAGNOSTICS

LX

5.

CHECK PTC NO. 1 RELAY

Install the FCM.

Install a substitute PTC No. 1 Relay in place of the vehicle’s PTC No. 1
Relay.

Turn the ignition on.

With the scan tool, erase FCM DTCs.

With the scan tool, actuate the PTC No. 1 Relay.

Monitor the scan tool for at least two minutes.

With the scan tool, read FCM DTCs.

Is the status Active for this DTC?

Yes

>> Go To 6

No

>> Replace the PTC No. 1 Relay in accordance with the Ser-

vice Information.

Perform the BODY VERIFICATION TEST VER 1. (Refer to
8 - ELECTRICAL/ELECTRONIC CONTROL MODULES/
FRONT CONTROL MODULE - DIAGNOSIS AND TEST-
ING).

6.

INSPECT RELATED WIRING & CHECK FOR TSBs

Turn the ignition off.

Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between the PTC No. 1 Relay
and the FCM.

Look for any chafed, pierced, pinched, or partially broken wires.

Look for broken, bent, pushed out or corroded terminals.

Refer to any Technical Service Bulletins that may apply.

Were any problems found?

Yes

>> Repair as necessary.

Perform the BODY VERIFICATION TEST VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES/FRONT CONTROL MODULE - DIAGNOSIS AND TESTING).

No

>> Replace the FCM in accordance with the Service Information.

Perform the BODY VERIFICATION TEST VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES/FRONT CONTROL MODULE - DIAGNOSIS AND TESTING).

LX

HVAC - ELECTRICAL DIAGNOSTICS

24 - 205

 

 

 

 

 

 

 

Content   ..  2290  2291  2292  2293   ..