Chrysler 300/300 Touring/300C, Dodge Magnum. Manual - part 1139

 

  Index      Chrysler     Chrysler 300/300 Touring/300C, Dodge Magnum - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1137  1138  1139  1140   ..

 

 

Chrysler 300/300 Touring/300C, Dodge Magnum. Manual - part 1139

 

 

4.

INTERMITTENT SPEED CONTROL SWITCH 1/2 STUCK DTC

The conditions necessary to set this DTC are not present at this time.

While monitoring the scan tool data relative to this circuit, move the Speed Control Switch to each position several
times.

Look for the DTC to reset while the switch is being moved to each position.

Were any problems found?

Yes

>> Repair as necessary.

No

>> Test complete.

9 - 580

ENGINE ELECTRICAL DIAGNOSTICS

LX

P0600-SERIAL COMMUNICATION LINK

For a complete wiring diagram Refer to Section 8W.

When Monitored:
With the ignition on.

Set Condition:
Internal Bus communication failure between processors. One Trip Fault. Three Global Good Trips to Clear.

Possible Causes

PCM

Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING).

Diagnostic Test

1.

PCM

NOTE: Diagnose any CMP or CKP Sensor faults before continuing. Check for intermittent loose CMP or CKP
connections.

The Powertrain Control Module is reporting internal errors, view repair to continue.

Repair

Replace and program the Powertrain Control Module per Service Information.

Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)

LX

ENGINE ELECTRICAL DIAGNOSTICS

9 - 581

P0601-INTERNAL MEMORY CHECKSUM INVALID

For a complete wiring diagram Refer to Section 8W.

When Monitored:
With the ignition on.

Set Condition:
Internal checksum for software failed, does not match calculated value. One Trip Fault, Three Good Trips to
clear.

Possible Causes

PCM

Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING).

Diagnostic Test

1.

PCM

NOTE: Diagnose any CMP or CKP Sensor faults before continuing. Check for intermittent loose CMP or CKP
connections.

The Powertrain Control Module is reporting internal errors, view repair to continue.

Repair

Replace and program the Powertrain Control Module per Service Information.

Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)

9 - 582

ENGINE ELECTRICAL DIAGNOSTICS

LX

P0606-INTERNAL ECM PROCESSOR

For a complete wiring diagram Refer to Section 8W.

When Monitored:
Engine running.

Set Condition:
When the PCM recognizes an internal failure to communicate with the ECM or the CMP and CKP Sensor
count periods are too short. One trip fault. ETC light is flashing.

Possible Causes

PCM

Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING).

Diagnostic Test

1.

PCM

NOTE: Diagnose any CMP or CKP Sensor faults before continuing. Check for intermittent loose CMP or CKP
connections.

The Powertrain Control Module is reporting internal errors, view repair to continue.

Repair

Replace and program the Powertrain Control Module per Service Information.

Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)

LX

ENGINE ELECTRICAL DIAGNOSTICS

9 - 583

 

 

 

 

 

 

 

Content   ..  1137  1138  1139  1140   ..