|
|
Control Module References for EBCM or IPC replacement, setup, and programming TRACTION OFF INDICATOR MALFUNCTION Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Diagnostic Procedure Instructions provides an overview of each diagnostic category. Circuit/System Description The Low Traction indicator is controlled by the instrument cluster via serial data messages from The electronic brake control module (EBCM) sends a serial data message to the instrument panel Reference Information Schematic Reference Antilock Brake System Schematics Connector End View Reference Component Connector End Views Description and Operation ABS Description and Operation (With JL4) or ABS Description and Operation (Without Electrical Information Reference Circuit Testing Connector Repairs
2008 Chevrolet Silverado 1500 2008 BRAKES Antilock Brake System - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
Testing for Intermittent Conditions and Poor Connections Wiring Repairs Scan Tool Reference Control Module References for EBCM and IPC Circuit/System Verification 1. Turn OFF the ignition for 5 seconds. 2. Turn ON the ignition, with a scan tool, select instrument panel special functions Display Test. Command the instrument panel lamps ON. Verify the traction control off lamp Circuit/System Testing 1. Ignition OFF for 5 seconds, Igniton ON, observe that the traction off indicator functions by illuminating for 2 seconds then turns OFF. If the traction OFF indicator does not illuminate, with the scan tool, select instrument If the TC warning lamp does not turn OFF, replace the IPC. If the TC warning lamp does turn OFF, replace the EBCM. Repair Procedures Perform the Diagnostic Repair Verification after completing the diagnostic procedure. Control Module References for EBCM or IPC replacement, setup, and programming Repair Validation Ignition OFF for 5 seconds, Igniton ON, observe that the traction control off indicator functions IMPORTANT: Diagnose all vehicle DTCs before using this diagnostic. The malfunction must be present during diagnosis in order to
2008 Chevrolet Silverado 1500 2008 BRAKES Antilock Brake System - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
REPAIR INSTRUCTIONS ANTILOCK BRAKE SYSTEM AUTOMATED BLEED PROCEDURE (WITH JL4) 1. Install a scan tool to the vehicle. 2. Start the engine and allow the engine to idle. 3. Using the scan tool, begin the automated bleed procedure. 4. Follow the instructions on the scan tool to complete the automated bleed procedure. Apply the brake pedal when instructed by the scan tool. 5. Turn the ignition OFF. 6. Remove the scan tool from the vehicle. 7. Fill the brake master cylinder reservoir to the maximum-fill level with Delco Supreme 11®, GM P/N 12377967 (Canadian P/N 992667), or equivalent DOT-3 brake fluid from a clean, 8. Bleed the hydraulic brake system. Refer to Hydraulic Brake System Bleeding (Pressure) or Hydraulic Brake System Bleeding (Manual) . 9. With the ignition OFF, apply the brakes 3-5 times, or until the brake pedal becomes firm, in order to deplete the brake booster power reserve. 10. Slowly depress and release the brake pedal. Observe the feel of the brake pedal. 11. If the brake pedal feels spongy, repeat the automated bleeding procedure. If the brake pedal NOTE: When adding fluid to the brake master cylinder reservoir, use only NOTE: Refer to BRAKE FLUID EFFECTS ON PAINT AND ELECTRICAL IMPORTANT: The base hydraulic brake system must be bled before performing this automated bleeding procedure. If you have not yet performed
2008 Chevrolet Silverado 1500 2008 BRAKES Antilock Brake System - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
still feels spongy after repeating the automated bleeding procedure inspect the brake system 12. Turn the ignition key ON, with the engine OFF; check to see if the brake system warning lamp remains illuminated. 13. If the brake system warning lamp remains illuminated, DO NOT allow the vehicle to be driven until it is diagnosed and repaired. Refer to Symptoms - Hydraulic Brakes . 14. Drive the vehicle to exceed 13 km/h (8 mph) to allow ABS initialization to occur. Observe brake pedal feel. 15. If the brake pedal feels spongy, repeat the automated bleeding procedure until a firm brake pedal is obtained. ANTILOCK BRAKE SYSTEM AUTOMATED BLEED PROCEDURE (WITHOUT JL4) 1. Install a scan tool to the vehicle. 2. Start the engine and allow the engine to idle. 3. Depress the brake pedal firmly and maintain steady pressure on the pedal. NOTE: When adding fluid to the brake master cylinder reservoir, use only NOTE: Refer to BRAKE FLUID EFFECTS ON PAINT AND ELECTRICAL IMPORTANT: This procedure may be performed on all vehicles EXCEPT those equipped with option code JL4, Vehicle Stability Enhancement IMPORTANT: The base hydraulic brake system must be bled before performing this automated bleeding procedure. If you have not yet performed
2008 Chevrolet Silverado 1500 2008 BRAKES Antilock Brake System - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
|
|
|