|
|
Component Connector End Views Description and Operation SIR System Description and Operation Electrical Information Reference Circuit Testing Connector Repairs Testing for Intermittent Conditions and Poor Connections Wiring Repairs Scan Tool Reference Control Module References for scan tool information Circuit/System Testing 1. Verify DTC B0090 39 is not set. If DTC is set, replace the rollover sensor. 2. Ignition OFF, disconnect the harness connector at the rollover sensor and the SDM. 3. Test for less than 5 ohms between the rollover sensor ground circuit terminal 6 and ground. If greater then the specified range, test the circuit for an open/high resistance. 4. Test for less than 5 ohms between the serial data circuit terminal 5 and the SDM occupant sensor serial data circuit terminal 58. If greater then the specified range, test the circuit for a short to ground or an open/high 5. Ignition ON, test for less than 1 volt between the serial data circuit terminal 5 and ground. IMPORTANT: When removing connectors inspect for damage or corrosion. Damage or corrosion in the following requires repair or The vehicle rollover sensor The SDM module The vehicle rollover sensor harness connector The SDM wiring harness connector
2008 Chevrolet Silverado 1500 2008 RESTRAINTS Supplemental Inflatable Restraints - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
If greater then the specified range, test the circuit for a short to voltage. 6. Verify a test lamp illuminates between the B+ circuit terminal 1 and ground. If the test lamp does not illuminate, test the circuit for an open/high resistance. If the 7. With a scan tool, clear DTCs. Verify DTC B0090 is not set. If DTC is set, replace the SDM. Repair Procedures Perform the Diagnostic Repair Verification after completing the diagnostic procedure. Inflatable Restraint Vehicle Rollover Sensor Replacement SIR/SRS Wiring Repairs Control Module References for SDM and ROS replacement, setup, and programming. DTC B0098 Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using the diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Diagnostic Procedure Instructions provides an overview of each diagnostic category. DTC Descriptors DTC B0098 52 Manual Cutoff Switch Circuit Compare Failure Diagnostic Fault Information Circuit Short to Ground Open/High Resistance Short to Voltage Signal Performance I/P Module Disable Switch - B0098 52 B0098 52 - I/P Module Enable Switch B0098 52 B0098 52 B0098 52 - Ignition 1 Voltage B1370 06 B0098 52 - -
2008 Chevrolet Silverado 1500 2008 RESTRAINTS Supplemental Inflatable Restraints - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
Circuit/System Description The inflatable restraint I/P module disable switch is ignition key operated to manually enable or Conditions for Running the DTC Ignition 1 voltage is between 9-16 volts. Conditions for Setting the DTC The SDM detects both the I/P module disable switch signal circuit (ON) and the I/P module Action Taken When the DTC Sets The SDM commands the AIRBAG indicator ON. Conditions for Clearing the DTC The condition for setting the DTC no longer exists. A history DTC will clear once 100 malfunction-free ignition cycles have occurred. Reference Information Electrical Information Reference Circuit Testing Connector Repairs Testing for Intermittent Conditions and Poor Connections Wiring Repairs Circuit/System Testing IMPORTANT: When removing connectors inspect for damage or corrosion. Damage or corrosion in the following requires repair or
2008 Chevrolet Silverado 1500 2008 RESTRAINTS Supplemental Inflatable Restraints - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
1. Ignition OFF, disconnect the harness connector at the inflatable restraint I/P module disable switch. 2. Ignition ON, verify that a test lamp illuminates between the ignition circuit terminal B and ground. If the test lamp does not illuminate, test the ignition circuit for a short to ground or an 3. Verify that a test lamp illuminates between the I/P module disable switch signal control circuit terminal E and B+. If the test lamp does not illuminate, test the control circuit for a short to voltage or an 4. Verify that a test lamp illuminates between the I/P module suppression indicator control (OFF) circuit terminal A and B+. 5. If all circuits test normal, test or replace the inflatable restraint I/P module disable switch. Component Testing 1. Ignition OFF, disconnect the harness connector at the inflatable restraint I/P module disable switch. 2. Test for infinite resistance between the signal circuit terminal A and the signal circuit terminal E. If not the specified value, inflatable restraint I/P module disable switch. 3. With the inflatable restraint I/P module disable switch select the OFF position. 4. Test for 90-110 ohms between the ignition circuit terminal B and signal circuit terminal E. If not the specified range, replace the inflatable restraint I/P module disable switch. 5. With the inflatable restraint I/P module disable switch select the ON position. 6. Test for 3.9K-3.2K ohms between the ignition circuit terminal B and signal circuit terminal A. replacement of the affected component/connector. The inflatable restraint I/P module disable switch The SDM The inflatable restraint I/P module wiring harness The SDM wiring harness connector
2008 Chevrolet Silverado 1500 2008 RESTRAINTS Supplemental Inflatable Restraints - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
|
|
|