|
|
Content .. 2964 2965 2966 2967 ..
Schematic Reference Moveable Window Schematics Door Control Module Schematics Connector End View Reference Component Connector End Views Description and Operation Power Windows Description and Operation Electrical Information Reference Circuit Testing Connector Repairs Testing for Intermittent Conditions and Poor Connections Wiring Repairs Scan Tool Reference Control Module References for scan tool information Circuit/System Verification 1. Ignition ON, observe the operation of the power windows while commanding each window UP and DOWN by using their respective window switches, each window should perform If the driver window is inoperative, refer to Driver Window Malfunction. If the front passenger window is inoperative, refer to Passenger Window Malfunction. If either rear passenger power window is inoperative, refer to Rear Passenger Window 2. Observe the scan tool Driver RF Window Switch, Driver LR Window Switch and Driver RR Window Switch parameters while using the driver master control switches. The If the parameter does not change, replace the DDS. 3. Observe the scan tool Window Lockout Switch parameter while pressing and depressing the window lockout switch on the driver master control. The parameter should change between
2008 Chevrolet Silverado 1500 2008 ACCESSORIES & EQUIPMENT Fixed and Moveable Windows - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
On and Off. If the parameter does not change, replace the DDS. Circuit/System Testing Driver Power Window Inoperative 1. Ignition OFF, disconnect the X1 harness connector at the DDS. 2. Test for less than 15 ohms between the ground circuit terminal 6 and ground. If greater than the specified range, test the ground circuit for an open/high resistance. 3. Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal 2 and ground. If the test lamp does not illuminate, test the B+ circuit for a short to ground or an 4. Ignition OFF, connect the harness connector at the DDS. 5. Ignition ON, observe the scan tool Driver LF Window Switch parameters while using the driver power window switch. The reading should change between Off/Up/Down/Express If the parameter does not change, replace the DDS. 6. Ignition OFF, disconnect the harness connector at the driver window motor. 7. Connect a test lamp between control circuit terminal A and control circuit terminal B. 8. Ignition ON, command the driver window UP and DOWN by using the driver window switch. The test lamp should illuminate when commanding the UP and DOWN states. If the test lamp is always OFF during either of the commands, test either control circuit If the test lamp is always ON, test either control circuit for a short to voltage. If the 9. If all circuits test normal, test or replace the driver window motor. Passenger Power Window Inoperative 1. Ignition OFF, disconnect the X1 harness connector at the PDS. 2. Test for less than 1 ohm between the ground circuit terminal 6 and ground. If greater than the specified range, test the ground circuit for an open/high resistance. 3. Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal 2 and ground.
2008 Chevrolet Silverado 1500 2008 ACCESSORIES & EQUIPMENT Fixed and Moveable Windows - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
If the test lamp does not illuminate, test the B+ circuit for a short to ground or an 4. Ignition OFF, reconnect the harness connector at the PDS. 5. Ignition ON, observe the scan tool Passenger Window Switch parameters while using the passenger power window switch. The reading should change between If the parameter does not change, replace the PDS. 6. Ignition OFF, disconnect the harness connector at the passenger window motor. 7. Test for less than 1 ohm between the control circuit terminal A and ground If greater than the specified range, test the control circuit for a short to voltage or an 8. Test for less than 1 ohm between the control circuit terminal B and ground If greater than the specified range, test the control circuit for a short to voltage or an 9. Connect a test lamp between control circuit termina A and control circuit terminal B. 10. Ignition ON, command the passenger window UP and DOWN by using the passenger window switch. The test lamp should illuminate when commanding the UP and DOWN If the test lamp is always OFF during either of the commands, test either control circuit 11. If all circuits test normal, test or replace the passenger window motor. Rear Power Window Inoperative 1. Ignition OFF, disconnect the harness connector at the appropriate rear window switch. 2. Test for less than 1 ohm between the ground circuit terminal F and ground. If greater than the specified range, test the ground circuit for an open/high resistance. 3. Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal G and ground. If the test lamp does not illuminate, test the B+ circuit for a short to ground or an 4. Enable the rear windows by using the window lockout switch. 5. Test for more than 10 volts on the control circuit terminal D. If less than the specified range, test the control circuit for a short to ground or
2008 Chevrolet Silverado 1500 2008 ACCESSORIES & EQUIPMENT Fixed and Moveable Windows - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
6. Test for more than 10 volts on the signal circuit terminal C while commanding the rear window DOWN with a scan tool. If less than the specified range, test the signal circuit for a short to ground or open/high 7. Test for more than 10 volts on the signal circuit terminal A while commanding the rear window UP with a scan tool. If less than the specified range, test the signal circuit for a short to ground or open/high 8. Ignition OFF, connect harness connector at the rear window switch and disconnect the harness connector at the rear window motor 9. Test for less than 1 ohm between the control circuit terminal A and ground If greater than the specified range, test the control circuit for a short to voltage or an 10. Test for less than 1 ohm between the control circuit terminal B and ground If greater than the specified range, test the control circuit for a short to voltage or an 11. Connect a test lamp between control circuit terminal A and control circuit terminal B. 12. Ignition ON, command the rear window UP and DOWN by using the rear window switch. The test lamp should illuminate when commanding the UP and DOWN states. If the test lamp is always OFF during either of the commands, test either control circuit 13. If all circuits test normal, test or replace the rear window motor. Component Testing 1. Ignition OFF, disconnect the harness connector at the appropriate window motor. 2. Install a 25-amp fused jumper wire between the control terminal A and 12 volts. Momentarily install a jumper wire between the control terminal B and ground. The window If the function does not perform as specified, replace the window motor. 3. Reverse the jumper wires; the appropriate window motor should perform the DOWN or UP function. If the function does not perform as specified, replace the window motor Repair Procedures Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
2008 Chevrolet Silverado 1500 2008 ACCESSORIES & EQUIPMENT Fixed and Moveable Windows - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
Content .. 2964 2965 2966 2967 ..
|
|
|