|
|
Content .. 2427 2428 2429 2430 ..
Air Bag Indicator Circuit Malfunction Passenger Presence System Indicator Circuit Malfunction Seat Belt Indicator Circuit Malfunction - Driver Seat Belt Indicator Circuit Malfunction - Passenger Security Indicator Malfunction Outside Air Temperature Display Inaccurate or Inoperative Instrument Cluster Dimming Interior Backlighting Malfunction (w/AN3) or Interior Backlighting Malfunction (w/o Driver Information Center (DIC) Driver Information Center (DIC) Switch Malfunction Audible Warnings Chime Malfunction CHARGE INDICATOR MALFUNCTION Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Diagnostic Procedure Instructions provides an overview of each diagnostic category. Circuit/System Description The engine control module (ECM) uses the generator turn ON signal circuit to control the load of Reference Information
2008 Chevrolet Silverado 1500 2008 ACCESSORIES & EQUIPMENT Displays and Gages - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
Schematic Reference Instrument Cluster Schematics Starting and Charging Schematics Connector End View Reference Component Connector End Views Description and Operation Instrument Cluster Description and Operation Charging System Description and Operation Electrical Information Reference Circuit Testing Connector Repairs Testing for Intermittent Conditions and Poor Connections Wiring Repairs Scan Tool Reference Control Module References for scan tool information Circuit/System Verification 1. Ignition ON, engine running, verify the scan tool Battery Voltage parameter is between 12.5 and 15.5 volts. If not within the specified range, refer to Charging System Test . 2. Ignition ON, perform the display test with the scan tool. The charge indicator should turn ON and OFF when changing between the commanded states. If the indicator does not turn ON and OFF between commanded states, replace the Repair Procedures Perform the Diagnostic Repair Verification after completing the diagnostic procedure. Control Module References for the IPC replacement, setup, and programming
2008 Chevrolet Silverado 1500 2008 ACCESSORIES & EQUIPMENT Displays and Gages - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
CHIME MALFUNCTION Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach. Diagnostic Procedure Instructions provides an overview of each diagnostic category. Diagnostic Fault Information Circuit/System Description The radio generates the audible warning through the left speaker. The radio receives audible Reference Information Schematic Reference Instrument Cluster Schematics Audible Warnings Schematics Body Control System Schematics Radio/Navigation System Schematics Connector End View Reference Component Connector End Views Description and Operation Audible Warnings Description and Operation Electrical Information Reference Circuit Short to Ground Open/High Resistance Short to Voltage Signal Performance Key In Ignition B+ - 1 - - Key In Ignition Signal 1 1 1 - 1. Chime Malfunction
2008 Chevrolet Silverado 1500 2008 ACCESSORIES & EQUIPMENT Displays and Gages - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
Circuit Testing Connector Repairs Testing for Intermittent Conditions and Poor Connections Wiring Repairs Scan Tool Reference Control Module References for scan tool information Circuit/System Verification 1. Ignition ON, headlamp switch OFF, verify the scan tool Headlamp Switch ON parameter is Inactive. If not Inactive, refer to Headlamps Malfunction . 2. Ignition ON, park lamp switch OFF, verify the scan tool Park Lamp Switch parameter is Inactive. If not Inactive, refer to Park, License, and/or Tail Lamps Malfunction . 3. Ignition ON, doors closed, verify the scan tool Door Ajar Switch parameters are Inactive/Door Closed. If not Inactive/Door Closed, refer to Courtesy Lamps Malfunction (w/AN3) or 4. Ignition ON, radio ON, adjust the radio balance and fade to the left front speaker. If the speaker does not operate properly, refer to Speaker Malfunction . 5. Verify that the Key In Ignition Status parameter is Key In when the key is in the ignition and Key Out when the key is out of the ignition. Circuit/System Testing 1. Ignition OFF, disconnect the harness connector at the ignition switch. 2. Ignition ON, verify that a test lamp illuminates between the B+ circuit terminal 4 and ground. If the test lamp does not illuminate, test the B+ circuit for an open/high resistance. If IMPORTANT: Before performing this diagnostics, make sure no indicator(s) are illuminated after the IPC performs the displays test. If any
2008 Chevrolet Silverado 1500 2008 ACCESSORIES & EQUIPMENT Displays and Gages - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
Content .. 2427 2428 2429 2430 ..
|
|
|