|
|
Content .. 2304 2305 2306 2307 ..
3 The liquid line between the condenser and Go to Step 7 Go to Step 4 4 1. Feel the liquid line at the expansion device location for extreme cold, possibly 2. Feel along the liquid line beyond the expansion device location for warm Is the liquid line extremely cold at the Go to Step 11 Go to Step 5 5 Feel along the surfaces of the following low The evaporator inlet tube between the The evaporator outlet tube between the The accumulator The compressor suction hose Go to Step 7 Go to Step 6 Feel along the surfaces of the low and the high The evaporator inlet tube between the The evaporator outlet tube between the
2008 Chevrolet Silverado 1500 2008 HVAC Heating, Ventilation, and Air Conditioning - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
6 The accumulator The compressor suction hose The compressor discharge hose The condenser The evaporator inlet tube between the Go to Step 14 Go to Step 8 7 1. Recover the refrigerant. Refer to Refrigerant Recovery and Recharging. 2. Remove the restriction from the component, or replace the component Is the repair complete? Go to Step 9 - 8 1. Recover the refrigerant and evacuate the system. Refer to Refrigerant Recovery 2. Record the weight of the recovered refrigerant. 3. Compare the weight of the recovered refrigerant with the system capacity. Refer Is the weight of the recovered refrigerant charge Go to Step 9 Go to Step 10 9 Recharge the A/C system. Refer to Refrigerant Go to Step 21 Go to Step 10 10 1. Leak test the system. Refer to Leak Testing. 2. Repair any leaks.
2008 Chevrolet Silverado 1500 2008 HVAC Heating, Ventilation, and Air Conditioning - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
Is the repair complete? Go to Step 21 - 11 The expansion device is restricted. Go to Step 12 Go to Step 13 12 1. Remove the suction line from the vehicle. Refer to Suction Hose Replacement 2. Inspect the hose for debris by blowing shop air through one end of the hose while 3. Observe the amount of debris collected in the shop towel. Did a large amount of debris collect in the shop Go to Step 18 Go to Step 20 13 If the expansion device was restricted with a 1. Flush the A/C system. Refer to Flushing. 2. Replace the accumulator. Refer to Air Conditioning Accumulator Go to Step 21 - 14 1. Recover the refrigerant. Refer to Refrigerant Recovery and Recharging. 2. Disconnect the suction and the discharge lines from the compressor. Refer to
2008 Chevrolet Silverado 1500 2008 HVAC Heating, Ventilation, and Air Conditioning - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
3. Inspect for the presence of debris in the compressor suction port. Is debris present in the compressor suction port? Go to Step 15 Go to Step 19 15 1. Remove the debris from the suction port. 2. Inspect the expansion device for damage or debris. Refer to Expansion (Orifice) Did you find evidence of damage or debris? Go to Step 17 Go to Step 16 16 If the expansion device does not show any signs 1. Remove the suction line from the vehicle. Refer to Suction Hose Replacement 2. Inspect the hose for debris by blowing shop air through one end of the hose while 3. Observe the amount of debris collected in the shop towel. Go to Step 18 Go to Step 19 17 1. Replace the expansion device. Refer to Expansion (Orifice) Tube 2. If the expansion device was restricted, observe the type of debris present. Are metal flakes present? Go to Step 12 Go to Step 13 18 If a large amount of debris was collected in the
2008 Chevrolet Silverado 1500 2008 HVAC Heating, Ventilation, and Air Conditioning - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
Content .. 2304 2305 2306 2307 ..
|
|
|