|
|
Content .. 1531 1532 1533 1534 ..
The DTC will be current for as long as the fault is present. When the fault is no longer present, the DTC will be a history status code. A history DTC will clear after 50 ignition cycles or with a scan tool using the clear DTCs Reference Information Schematic Reference Door Control Module Schematics Connector End View Reference Component Connector End Views Description and Operation Power Door Locks Description and Operation Electrical Information Reference Circuit Testing Connector Repairs Testing for Intermittent Conditions and Poor Connections Wiring Repairs Scan Tool Reference Control Module References for Scan Tool Information Circuit/System Verification 1. Install a scan tool and display the inputs data list of the affected door module. If any of the integrated switch inputs are displayed as Active while in an inactive state, 2. Clear the DTCs. 3. Activate all of the integrated switch functions. If the DTC resets, replace the affected door module. Repair Procedures
2008 Chevrolet Silverado 1500 2008 ACCESSORIES & EQUIPMENT Vehicle Access - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
Perform the Diagnostic Repair Verification after completing the diagnostic procedure. Control Module References for driver or passenger door loch and side window switch DTC B3125 Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach Diagnostic Procedure Instructions provides an overview of each diagnostic category DTC Descriptor DTC B3125 00 Driver Door Only Unlock Circuit Circuit/System Description The body control module (BCM) energizes the driver door unlock relay coil through a low side Conditions for Running the DTC Battery voltage is between 9-16 volts. The BCM has attempted to energize the unlock relay. Conditions for Setting the DTC The driver door unlock relay control circuit is shorted to voltage. Action Taken When the DTC Sets The BCM will not attempt unlock operation. Conditions for Clearing the DTC When the output request is not active the DTC will be a history status code. The history code will clear after 50 fault free ignition cycles or by using the scan tool clear
2008 Chevrolet Silverado 1500 2008 ACCESSORIES & EQUIPMENT Vehicle Access - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
Reference Information Schematic Reference Door Lock/Indicator Schematics Connector End View Reference Component Connector End Views Description and Operation Power Door Locks Description and Operation Electrical Information Reference Circuit Testing Connector Repairs Testing for Intermittent Conditions and Poor Connections Wiring Repairs Scan Tool Reference Control Module References for Scan Tool Information Circuit/System Testing 1. Disconnect the BCM connector X7 and connect a test lamp from terminal 6 to ground. 2. Ignition ON, verify that the test lamp does not illuminate. If the test lamp illuminates test the control circuit for a short to voltage. If the circuit 3. If the circuits test normal replace the BCM. Repair Procedures Perform the Diagnostic Repair Verification after completing the diagnostic procedure. Instrument Panel Electrical Center or Junction Block Replacement - Left Side Control Module References for BCM replacement, programming, and setup. DTC B3130
2008 Chevrolet Silverado 1500 2008 ACCESSORIES & EQUIPMENT Vehicle Access - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for an overview of the diagnostic approach Diagnostic Procedure Instructions provides an overview of each diagnostic category DTC Descriptor DTC B3130 00 All Door Unlock Circuit Circuit/System Description The body control module (BCM) energizes the unlock relay coil through a low side drive control Conditions for Running the DTC Battery voltage is between 9-16 volts. The BCM has attempted to energize the unlock relay. Conditions for Setting the DTC The door unlock control circuit is shorted to voltage. Action Taken When the DTC Sets The BCM will not attempt unlock operation. Conditions for Clearing the DTC When the output request is not active the DTC will be a history status code. The history code will clear after 50 fault free ignition cycles or by using the scan tool clear Reference Information Schematic Reference Door Lock/Indicator Schematics
2008 Chevrolet Silverado 1500 2008 ACCESSORIES & EQUIPMENT Vehicle Access - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
Content .. 1531 1532 1533 1534 ..
|
|
|