Chery QQ6 (S21) / S12LHD. Manual - part 68

 

  Index      Chery     Chery QQ6 (S21) / S12LHD - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  66  67  68  69   ..

 

 

Chery QQ6 (S21) / S12LHD. Manual - part 68

 

 

4.2. Mileage setting 

The upper right of the odometer displays the one-way mileage (switchable), and the lower right 

displays the total mileage. In the case of vehicle equipped with reversing radar, when the reverse 

gear is engaged, the distance behind the vehicle can be displayed on the upper right of odometer. 

4.3. Maintenance indicator light reset 

        In case that the ignition switch turns off, press the regulating button, 3 s later, after the 

ignition switch turns on, release the button,, and then the indicator light automatically resets.   

5. Battery Check   

 

 

Check whether the connection of battery is secure and reliable; observe the prompt in the 

battery status access hole, and charge or replace the battery if necessary.   

The vehicle equipps with the maintenance-free battery, and it is not recommended to use other 

types of batteries. If it is necessary to replace the battery, the current and capacity of a new battery 
must conform to that of old battery or CHERY’s specifications available.   

6. Airbag Check   

 

 

Access Hole 

Airbag 

 

The air bag is an optional configuration. If your vehicle is equipped with the air bags, please 

ensure that there is clean and no damage in the “air bag” positions shown in the figure above. DO 

NOT let any cleaning fluid or liquid enter into the aribags. 

7.    Engine Oil Check   

7.1. Oil level check   

 

 

Engine  oil  consumption  is  affected  by  many  factors.  A  new  engine  reaches  the  normal  value  only 
after the mileage of approx. 5,000 KM. More engine oil might be consumed under the high-load of 
engine. 

Stop  your  vehicle  on  a  level  surface  before  the  engine  oil  check.  Turn  off  the  ignition  switch  and 
wait  for  a  few  minutes  to  let  the  engine  oil  flows  into  the  oil  pan  (it  may  spend  more  time  if  the 
exterior  temperature  is  low  or  the  temperature  of  engine  does  not  reach  the  normal  working 
temperature). Before the engine oil check, please DO NOT start up the engine in the cold state. Pull 
out the dipstick and clean it  with a flannelette-free cloth, and  then fully insert the  dipstick into the 
tank and pull it out again. 

If the oil level is between MIN and MAX marks at the lower of dipstick, DO NOT refill the oil. The 
hot engine oil may exceed the upper mark several millimeters due to its thermal expansion. 

7.2. Method to replace the engine oil 

In case that the engine oil is replaced, it is necessary to wait until the engine cools down to the 

normal temperature, and then replace the engine oil according to the following procedures:   

Ø  Stop the vehicle over a jack, and then unscrew the filler cap (the cap is shown in the figure 

below);   

Ø  Lift the vehicle up to an appropriate height, unscrew the drain plug with a torque wrench, 

and flow the used engine oil into a container at the same time.;   

Ø  Then, tighten the drain plug with the torque wrench to the specified torque (25±3Nm);   
Ø  Jack down the vehicle, and then refill proper quantity of new engine oil according to the 

specifications;   

Ø  Screw up the filler cap.   

 

 

 

 

 

 

MAX  MIN 

The oil refilled shall not 
exceed the upper limit. 

Note: Please refill the engine oil conforming to the CHERY’s specifications only to the level 

between MIN and MAX marks.   

8. Transmission Oil Check   

8.1. Oil level check   

Shut down the engine and wait for several minutes, and then lift up the vehicle with a jack, unsrew 

the oil limiting plug with a torque wrench, and check the transmission oil level. If the distance 

between the oil level and filler opening is large, please appropriately refill the transmission oil (until 

the oil level increases up to the filler opening), and then tighten the oil limiting plug with a torque 

wrench to the specified torque. (The tightening torque of 44Nm for QR513MHA, and tightening 

torque of 30Nm for QR512.) 

 

 

8.2. Method to replace the transmission oil 

Shut down the engine and wait for several minutes, and then lift up the vehicle with a jack, unsrew 

the refiller plug with a torque wrench, and then carefully unscrew the drain plug and collect the used 

transmission oil with a container. In case that the used transmission oil nearly drains away, tighten 

the drain plug with a torque wrenchto the specified torque; and then refill the transmission oil 

specified by the CHERY Company (until the oil level increases up to the filler opening according to 

the specified quantity). Then tighten the refiller plug with a torque wrench to the specified torque. 

9. Trouble Diagnosis of Electronic Control System

 

Please utilize the CHERY Company’s special diagnostic testers X431 and K81/K61 to diagnose the 

electronic control system, and the updated version of program of the diagnostic testers is also 

required at the same time. 

Drain Plug 

Oil Limiting Plug 

10. Lubrication and Maintenance of All Hinges and Door Locks 

All the hinges and door locks are the maintenance-free products. Please make certain that the bush 

of any hinge is in good condition. If damaged, replace it in time. 

11. Wiper System Check   

11.1. Wiper blade check and maintenance 

Check wiper blade 

 

Slide the tip of your finger on the edge of a wiper blade to check the roughness of the blade. The 

butter, silicone resin and fuel may enable the wiper blade not to normally work. It is recommended 

that the glass cleaning fluid is applied to clean the wiper blade. 

 

 

Replace the wiper blade 

 

Lift the wiper arm and make it perpendicular to the wiper blade. To remove the wiper blade, press 

down the retaining clip according to the arrow as shown in the figure, loosen the wiper blade and 

then pull out the wiper arm in the reverse direction. 

 

11.2. Nozzle check and adjustment 

Keep the nozzle clean. If the spraying angle is improper, please insert the needle-like article into the 

nozzle to adjust the spraying angle. If the spraying angle can’t be adjusted to its proper position, 

adjust it again.   

 

 

 

 

 

 

 

Content   ..  66  67  68  69   ..