Alfa Romeo Giulia (2018 year). Manual - part 12

Alternative Code Synchronization

To check whether the garage door or gate

motor has an alternative code, proceed

as follows:

1. Read the garage door or gate motor

manufacturer manual.

2. The portable remote control seems to

have programmed to the HomeLink

system, but the garage door or gate can

be neither opened or closed.

3. Push the programmed button and

keep it pushed (1, 2 or 3). With an

alternative code system, the indicator

flashes briefly, and then remains off for

two seconds.This sequence is repeated

for 20 seconds.

Warning!

Vehicle exhaust contains carbon

monoxide, a dangerous gas. Do not run your

vehicle in the garage while programming the

transceiver. Exhaust gas can cause serious

injury or death.

Your motorized door or gate will open

and close while you are programming the

universal transceiver. Do not program the

transceiver if people, pets or other objects

are in the path of the door or gate. Only use

this transceiver with a garage door opener

that has a “stop and reverse” feature as

required by Federal safety standards.This

includes most garage door opener models

manufactured after 1982. Do not use a

garage door opener without these safety

features. Call toll-free 1-800-355-3515 or,

on the Internet at HomeLink.com for safety

information or assistance.

Note:

To program Homelink using an

Alternative Code, the car must be within

range of the garage door. Activate the

handbrake and turn the ignition to ON,

without starting the engine.

Proceed as follows:

1. Locate the “Learn” or “Train” button on

the garage door or gate motor.The color

and position may vary depending on the

manufacturer (consult the garage door or

gate manual). Push the “Learn” or “Train”

button (this normally activates the

setting warning light).

2. Push the desired HomeLink button

(1, 2 or 3). When the HomeLink indicator

begins to flash slowly, move the portable

remote control one to three inches from

the HomeLink system (keeping the

programmable button pushed down).

3. Within 30 seconds, push the

programmed key (1, 2 or 3) and release it.

Push the programmed button a second

time and release it to conclude the

operation. For some motors, the

operation will probably have to be

repeated a third time to end the setting.

The motor should now be capable of

recognizing the signal transmitted by

HomeLink and then open/close the door

or gate.

Programming A Single Key

It is possible to program another

original remote control on an already

programmed HomeLink key by canceling

the previously stored frequency.

Warning!

Vehicle exhaust contains carbon

monoxide, a dangerous gas. Do not run your

vehicle in the garage while programming the

transceiver. Exhaust gas can cause serious

injury or death.

Your motorized door or gate will open and

close while you are programming the

universal transceiver. Do not program the

transceiver if people, pets or other objects

are in the path of the door or gate. Only use

this transceiver with a garage door opener

that has a “stop and reverse” feature as

required by Federal safety standards.This

includes most garage door opener models

manufactured after 1982. Do not use a

garage door opener without these safety

features. Call toll-free 1-800-355-3515 or,

on the Internet at HomeLink.com for safety

information or assistance.

Note:

Activate the handbrake and place

the ignition to ON without starting the

engine.

Proceed as follows:

1. Push the desired HomeLink button

and keep it pushed (1, 2 or 3). Do not

release the button until the last

operation has been performed.

2. When the HomeLink indicator begins

to flash slowly, move the portable remote

control 1 to 3 inches from the system

(keeping the programmable button

pressed down).

If the indicator does not begin to flash

quickly, change the distance between the

HomeLink and the portable remote

control and try the procedure again.

The HomeLink indicator flashes, first

slowly and then quickly. When the

indicator starts to flash quickly, release

both buttons on the remote control.

The system previously programmed to

HomeLink has now been deleted and the

new system is ready to use.This does not

affect the other two HomeLink buttons in

any way.

Deleting Programmed Keys

It is recommended to delete HomeLink

programming before selling the car.

Proceed as follows:

1. Push and hold the outer buttons

(1 and 3). After about ten seconds, the

indicator will start to flash.

2. Release both keys.

Technical Information For After Sales

Service

If you are unable to set up HomeLink

successfully after following the above

instructions, contact After Sales Service

(HomeLink free hotline number

1-800-355-3515 ) with the following

information:

Vehicle make and model, including

manufacturing year and country of

purchase;

Make, model, age and frequency of use

of the original portable remote control

(if known).

General Information

The following regulatory statement

applies to all Radio Frequency (RF)

devices equipped in this vehicle:

This device complies with Part 15 of the

FCC Rules and with Industry Canada

license-exempt RSS standard(s).

Operation is subject to the following two

conditions:

1. This device may not cause harmful

interference, and

2. This device must accept any

interference received, including

interference that may cause undesired

operation.

Note:

Center Console

The center console storage compartment

is located between the front seats.

To access the center console storage, lift

the upper part of the center console as

shown below.

Warning!

Do not operate this vehicle with a console

compartment lid in the open position.

Driving with the console compartment lid

open may result in injury in a collision.

04246S0004EM

Center Console

Cupholder

Two cupholders are available in the

center console.

To access the cupholders, slide the cover

forward.To close the compartment, push

the cover and it will close automatically.

ENVIRONMENTAL PROTECTION

SYSTEMS

The following systems are used for

reducing engine emissions:

Catalytic Converter

Oxygen Sensors

Evaporation Control System

ACTIVE AERODYNAMICS

Carbon Fiber Active Aero Front Spoiler

This is an automatic device, working at

the vehicle speed, which allows higher

reactivity at average speeds and higher

vehicle stability at high speeds,

regulating the air flow into the lower part

of the vehicle.

Note:

The system is not active in

temperatures near or below zero, or

when the Alfa DNA Pro selector is in the

"Natural" or "Advanced Efficiency"

positions.

If there is a fault, a generic failure icon

will light up on the instrument panel

display, along with a message that will

identify the type of malfunction. See your

authorized dealer if a fault occurs.

04246S0005EM

Cupholders In Center Console

1— Cover

04296S0001EM

Front Fascia

INSTRUMENT PANEL FEATURES

Instrument Cluster

1. Tachometer

2. Digital Engine OilTemperature Gauge With Overheating Warning Light

3. Instrument Cluster Display

4. Digital Fuel Level Gauge (TheTriangle OnThe Left Side OfThe Symbol IndicatesThe Side OfThe Vehicle WithThe Fuel Door)

5. Speedometer (Speed Indicator)

05026S0006EM

Instrument Cluster