FANUC Series 30i/300i/300is-MODEL A. Machining Center System. User's manual - page 306

 APPENDIX 

B-63944EN/03

 

 

- 2404 - 

I. PC TOOL FOR MEMORY CARD 

PROGRAM OPERATION/EDITING 

I.3.1 

Usable Characters in Program File 

 

  - Usable characters in Control-in 

 

List of ANSI(ASCII) codes of usable characters(hexadecimal form)

 

Code Character Code Character Code Character Code Character 

0a LF  3f  ?  58  X  74  t 
23 # 40 @ 59 Y 75 u 
26 & 41 A 5a Z 76 v 
28 ( 42 B 5b [ 77 w 
29 ) 43 C 5d ] 78 x 
2a * 44 D 5f _ 79 y 
2b + 45 E 61 a 7a z 
2c , 46 F 62 b     
2d - 47 G 63 c     
2e . 48 H 64 d     

2f  / 49 I 65 e     

30 0 4a J 66 f     
31 1 4b K 67 g     
32 2 4c L 68 h     
33  3  4d M 69  i     
34 4 4e N 6a  j     
35 5 4f O 6b k     
36 6 50 P 6c  l     
37 7 51 Q 6d m     
38 8 52 R 6e n     
39 9 53 S 6f  o     
3a : 54 T 70 p     
3c < 55 U 71 q     
3d = 56 V 72  r     
3e > 57 W 73 s     

 

NOTE 

 

In the Control-in, "O", ":", and "<" can not be used 
at top of the line except for the 1

st

 line. 

 

B-63944EN/03

 APPENDIX 

 

 

- 2405 - 

I.PC TOOL FOR MEMORY CARD

PROGRAM OPERATION/EDITING

  - Usable characters in Control-out(characters in parentheses)

 

 

List of ANSI(ASCII) codes of usable characters(hexadecimal form)

 

Code Character Code Character Code Character Code Character 

0a LF 3c  <  55  U  71  q 
20 

SPC 

3d = 56 V 72  r 

22  “  3e > 57 W 73 s 
23 #  3f  ? 58 X 74  t 
24 $ 40 @ 59 Y 75 u 
26 & 41 A 5a Z 76 v 
27 ‘ 42 B 5b [ 77 w 
2a  *  43 C 5d  ]  78 x 
2b + 44 D 5f  _ 79 y 
2c  ,  45 E 61 a 7a z 
2d  -  46 F 62 b     
2e . 47 G 63 c     

2f  /  48 H 64 d     

30 0 49  I  65 e     
31 1 4a J 66  f     
32 2 4b K 67 g     
33 3 4c L 68 h     
34 4 4d M 69  i     
35 5 4e N 6a  j     
36 6 4f O 6b k     
37 7 50 P 6c  l     
38 8 51 Q 6d m     
39 9 52 R 6e n     
3a : 53 S 6f o     
3b ; 54 T 70 p     

 

 APPENDIX 

B-63944EN/03

 

 

- 2406 - 

I. PC TOOL FOR MEMORY CARD 

PROGRAM OPERATION/EDITING 

I.4 

ERROR MESSAGE AND NOTE 

 
Error may occur when using this application, hereafter explains the 
error messages and gives relative instructions. 

 

I.4.1 

List of Error Message 

 
When an error occurred, the error message box is displayed as 
follows.

 

 

Message

 

Remarks

 

Failed to open the file you specified. 

If failed to open once again, the file may be broken. 

Failed to read or write to the specified file.

 

There is insufficient disk space. 

There is no enough free space to create a new memory card 
program file or to put drop out files to work folder. In the latter 
case, please refer to chapter "Menu" [Change Work Folder] 

File name is not correct. 

Please refer to the chapter "Naming rules of Program file". 

Input name is already exists. 

Please input another name. 

File name is already exists. 

Please input another name. 

Input name is not correct. 

Please refer to the chapter "Naming rules". 

Please input an integer between 2 and 
2048 

The size of the memory card program file is available from 
2Mbyte to 2048Mbyte. 

An illegal character is included in the 
specified file. 

Please refer to the chapter "Rules of characters in Program file".

Last update time of the specified file is 
unsupported. 

The updating time of program file is available from 1997 to 2037.

The memory card program file you 
specified cannot be identified. 

The specified file format is not the memory card program file   

There is insufficient free folder. 

Please delete unnecessary program files or folders. 

There is insufficient free program space. 

Please delete unnecessary program files. 

Folder deeper than 7 cannot be created. 

 

Root folder cannot be deleted. 

 

Root folder cannot be renamed. 

 

Failed to create work folder. 

Please check whether the [temp] work folder is able to create or 
not. 
In default, the [temp] work folder is created on the same place of 
this PC tool "FPRG_30i.exe". 

Process has been cancelled. 

 

The specified work folder is not found. 

The Drop-out cannot be executed.   
Terminate this PC tool. And check the setting of Work Folder on 
the Option dialogue window. 

Only one instance of this application can 
be executed. 

Double activation of this PC tool cannot be executed. 

 

I.4.2 

Note 

 

  - Folder and Program Numbers 

Folder and Program Numbers can be selected among 63 / 500 / 1000. 
For selecting the Numbers of 500 or 1000, t

he option 

"Registered 

programs expan. On the memory card"

 is needed in CNC side.