Content .. 278 279 280 281 ..

FANUC Series 30i/300i/300is-MODEL A. Machining Center System. User's manual - page 280

A.PARAMETERS

APPENDIX

B-63944EN/03

- 2196 -

#7 #6 #5 #4 #3 #2 #1 #0

11221

MTW

[Input type] Parameter input

[Data type] Bit path

# 0

MTW

Multiple tilted working plane commands are:

0: Not

used.

1: Used.

#7 #6 #5 #4 #3 #2 #1 #0

11222

PDM

CIM

NIM

[Input type] Parameter input

[Data type] Bit path

# 0

NIM

Automatic conversion of a coordinate system by an inch/metric

conversion command (G20 or G21) is:
0: Not

performed.

1: Performed.

# 1

CIM

When an inch/metric conversion command (G20 or G21) is specified,

if the workpiece coordinate system is shifted by the shift amount as
described below:
0: An alarm (PS1298) is issued.
1: Clearing is performed.
If bit 0 (NIM) of parameter No. 11222 is set to 1, or if bit 2 (IRF) of
parameter No. 14000 is set to 1, this parameter clears the following:

•

Manual intervention made when the manual absolute signal is off

•

Issuance of a move command with the machine locked

•

Movement by handle interrupt

•

Operation with a mirror image

•

Shifting of a workpiece coordinate system when a local

coordinate system or workpiece coordinate system is set up

# 7

PDM

When switching between diameter and radius specification is made

with the function for dynamic switching of diameter/radius
specification, coordinates in the machine coordinate system select
command (G53) are:
0: Switched between diameter and radius specification.
1: Set according to the setting of bit 3 (DIAx) of parameter No.

1006.

#7 #6 #5 #4 #3 #2 #1 #0

11240

FAE

[Input type] Parameter input

[Data type] Bit path

# 0

FAE

During positioning when the AI contour control mode is canceled, the

optimum torque acceleration/deceleration is:
0: Disabled.
1: Enabled.

B-63944EN/03

APPENDIX

A.PARAMETERS

- 2197 -

11261

The amount of a retract operation in the tool axis direction during tool retract

and return

[Input type] Setting input

[Data type] Real axis

[Unit of data] mm, inch, degree (input unit)

[Minimum unit of data] Depend on the increment system of the reference axis

[Valid data range] 9 digit of minimum unit of data (refer to standard parameter setting

table (A))
(When the increment system is IS-B, -999999.999 to +999999.999

）

This parameter sets the amount of a retract operation in the tool axis
direction when G10.6 is specified alone during tool retraction and
return (during tool center point control and workpiece setting error
compensation). The retract operation is performed by using the value
set in this parameter in an incremental manner. This data is valid only
when bit 2 (RPS) of parameter No. 7040 is set to 1. If 0 is set in this
parameter, a retract operation in the tool axis direction is not
performed, but a retract operation is performed according to the
setting of parameter No. 7041.

#7 #6 #5 #4 #3 #2 #1 #0

11304

GGD

[Input type] Parameter input

[Data

type]

Bit

NOTE

When this parameter is set, the power must be
turned off before operation is continued..

# 1

GGD

The G code guidance screen is:

0: Not

displayed.

1: Displayed.

11305

Maximum number of simultaneously displayed axes

NOTE

When this parameter is set, the power must be
turned off before operation is continued.

[Input type] Parameter input

[Data type] Byte path

[Valid data range] 0 to 2

By setting this parameter, the maximum number of simultaneously
displayed axes at the current position can be changed. A value set in
this parameter corresponds to the maximum number of simultaneously
displayed axis as follows:

Max. number of simultaneously displayed axes

5 10

Setting 0

A value other than 1 and 2 is assumed to be 0.

A.PARAMETERS

APPENDIX

B-63944EN/03

- 2198 -

11307

Display sequence of the coordinates in current position display

NOTE

When this parameter is set, the power must be
turned off before operation is continued.

[Input type] Parameter input

[Data type] Byte path

[Valid data range] 0 to 5

This parameter sets the display sequence of the coordinates of a
position displayed on the following screens:
10.4- and 15-inch display units

•

Total position display screen

•

Total position display on each screen

7.2- and 8.4-inch display units

•

Total position display screen

When the maximum number of simultaneously displayed axes is set
to 20 (when 2 is set in parameter No. 11305), two sets of coordinates
are displayed simultaneously as the current position display on each
screen.

When the first set is displayed, switching to the second set can be
made by pressing

then pressing the chapter selection soft key

being selected.

When the above operation is performed again, the displayed set
changes to the first set.
The display sequence of coordinates corresponds to the parameter
setting as follows:

Display sequence of

coordinates

Setting

1 2 3 4

Relative

coordinates

Absolute

coordinates

Machine

coordinates

Remaining travel

distance

Relative

coordinates

Machine

coordinates

Absolute

coordinates

Remaining travel

distance

Relative

coordinates

Remaining travel

distance

Absolute

coordinates

Machine

coordinates

Absolute

coordinates

Machine

coordinates

Relative

coordinates

Remaining travel

distance

Absolute

coordinates

Remaining travel

distance

Relative

coordinates

Machine

coordinates

Machine

coordinates

Remaining travel

distance

Relative

coordinates

Absolute

coordinates

If the setting is beyond the valid data range, 0 is assumed.
When the multipath simultaneous display function is enabled
(parameter No. 13131 is set to a nonzero value, and parameter No.
13132 is set to 1 or a greater value), this parameter becomes invalid.

B-63944EN/03

APPENDIX

A.PARAMETERS

- 2199 -

#7 #6 #5 #4 #3 #2 #1 #0

11308

COW

[Input type] parameter input

[Data

type]

Bit

#1 COW

When the file of specified name already exists on memory card,

0: It is not overwritten

Alarm (SR1973 FILE ALREADY EXIST) is generated.

1: It is overwritten.
Because the confirmation message is displayed before

overwriting even if COW is 1, overwriting can be canceled.

NOTE

When the overwritten file is read only attribute, it is
not possible to overwrite even if parameter COW
(No.11308#1)=1.

#7 #6 #5 #4 #3 #2 #1 #0

11329

GST

BGM

[Input type] Parameter input

[Data type] Bit path

BGM

Coordinates used by the dynamic graphic display function are:

0: Absolute

coordinates.

1: Machine

coordinates.

GST

When drawing cannot be performed for a command with the dynamic

graphic display function:
0: The command is ignored, and drawing continues without

stopping drawing.

1: Drawing

stops.

11343

Blank figure in dynamic graphic display

[Input type] Parameter input

[Data type] Byte path

[Valid data range] 0 to 1

This parameter sets the type of a blank figure in dynamic graphic
display.

Setting Figure

Cylinder or hollow cylinder (parallel to the Z-axis)

1 Rectangular

parallelepiped

A.PARAMETERS

APPENDIX

B-63944EN/03

- 2200 -

11344

Blank reference position in dynamic graphic display

[Input type] Parameter input

[Data type] Real axis

[Unit of data] mm,inch (input unit)

[Minimum unit of data] Depend on the increment system of the applied axis

[Valid data range] 9 digit of minimum unit of data (refer to standard parameter setting

table (A))
(When the increment system is IS-B, -999999.999 to +999999.999

）

This parameter sets the reference position of a blank in the dynamic
graphic display function by using coordinate values in the workpiece
coordinate system.

NOTE

If bit 3 (BGM) of parameter No. 11329 is set to 1,
set coordinate values in the machine coordinate
system.

11345

Blank dimension I in dynamic graphic display

11346

Blank dimension J in dynamic graphic display

11347

Blank dimension K in dynamic graphic display

[Input type] Parameter input

[Data type] Real axis

[Unit of data] mm,inch (input unit)

[Minimum unit of data] Depend on the increment system of the reference axis

[Valid data range] 0 or positive 9 digit of minimum unit of data (refer to the standard

parameter setting table (B))
(When the increment system is IS-B, 0.000 to +999999.999

）

These parameters set the dimensions of a blank in the dynamic graphic
display function according to the blank figure as follows:

Blank type

Dimension I

Dimension

Ｊ

Dimension

Ｋ

Cylinder

Column diameter

Column length

Hollow

cylinder

Diameter of outer

circle of cylinder

Diameter of inner

circle of cylinder

Cylinder length

Rectangular

prism

Length in X-axis

direction

Length in Y-axis

direction

Length in Z-axis

direction

B-63944EN/03

APPENDIX

A.PARAMETERS

- 2201 -

#7 #6 #5 #4 #3 #2 #1 #0

11349

WNS

ABC

[Input type] Parameter input

[Data

type]

Bit

# 1

ABC

In animated simulation in the dynamic graphic display function, when

a fine boring cycle or back boring cycle, which is a hole machining
canned cycle, is performed, the movement for a shift at the hole
bottom is:
0: Not

drawn.

1: Drawn.

# 3

WNS

In the dynamic graphic display function, P-CODE workpiece number

search is:
0: Disabled.
1: Enabled.

NOTE

A macro executor option, or a macro executor and C
executor options are required.

#7 #6 #5 #4 #3 #2 #1 #0

11353

SEK

[Input type] Parameter input

[Data

type]

Bit

SEK

When the power is turned on, or when the clear state is present,

sequence numbers are:
0: Not

maintained.

1: Maintained.

NOTE

During a subprogram call, the sequence number of
the subprogram is maintained.

#7 #6 #5 #4 #3 #2 #1 #0

11630

FRD

[Data type] Bit path

# 0

FRD

The minimum command unit of the rotation angles of coordinate

rotation and three-dimensional coordinate system conversion is:
0: 0.001

degree.

1: 0.00001 degree. (1/100,000)

A.PARAMETERS

APPENDIX

B-63944EN/03

- 2202 -

12310

States of the manual handle feed axis selection signals when tool axis

direction handle feed/interrupt and table-based vertical direction handle

feed/interrupt are performed

[Input type] Parameter input

[Data type] Byte path

[Valid data range] 1 to 24

This parameter sets the states of the manual handle feed axis selection
signal (HS1A to HS1E for the first manual handle) or the manual
handle interrupt axis selection signal (HS1IA to HS1IE for the first
manual handle) to perform tool axis direction handle feed/interrupt
and table-based vertical direction handle feed/interrupt.
The handle for which the signal states are set is determined by
parameter No. 12323.

If parameter No. 12323 is set to 1, the states of the manual handle feed
axis selection signals or manual handle interrupt axis selection signals
for the first manual handle in the three-dimensional manual feed
(handle feed) mode and corresponding parameter settings are listed in
the table below. When the first manual handle pulse generator is
turned after setting the signals corresponding to the value set in the
parameter, operation is performed in the specified mode.

HS1E

(HS1IE)

HS1D

(HS1ID)

HS1C

(HS1IC)

HS1B

(HS1IB)

HS1A

(HS1IA)

Parameter

(No.12310)

0 0 0 0 1  1
0 0 0 1 0  2
0 0 0 1 1  3
0 0 1 0 0  4
0 0 1 0 1  5
0 0 1 1 0  6
0 0 1 1 1  7
0 1 0 0 0  8
0 1 0 0 1  9
0 1 0 1 0  10
0 1 0 1 1  11
0 1 1 0 0  12
0 1 1 0 1  13
0 1 1 1 0  14
0 1 1 1 1  15
1 0 0 0 0  16
1 0 0 0 1  17
1 0 0 1 0  18
1 0 0 1 1  19
1 0 1 0 0  20
1 0 1 0 1  21
1 0 1 1 0  22
1 0 1 1 1  23
1 1 0 0 0  24

If parameter No. 12323 is set to 2 to 5, replace "1" in HS1A to HS1E
and HS1IA to HS1IE above with 2 to 5.

B-63944EN/03

APPENDIX

A.PARAMETERS

- 2203 -

12311

States of the manual handle feed axis selection signals when a movement is

made in the first axis direction in tool axis normal direction handle

feed/interrupt and table-based horizontal direction handle feed/interrupt

[Input type] Parameter input

[Data type] Byte path

[Valid data range] 1 to 24

This parameter sets the states of the manual handle feed axis selection
signals (HS1A to HS1E for the first manual handle) or the manual
handle interrupt axis selection signal (HS1IA to HS1IE for the first
manual handle) when a movement is made in the first axis direction.
(For settings, see "Table of correspondence with the manual handle
feed axis selection signals" in the description of parameter No.
12310.)
The handle for which the signal states are set is determined by
parameter No. 12323.

The table below indicates the relationships of tool axis directions, first
axis directions, and second axis directions.

Parameter

No.19697

Tool axis

directions

First axis

directions

Second axis

directions

1 X Y Z
2 Y Z X
3 Z X Y

Note, however, that the table above indicates the directions applicable
when the angles of all rotation axes are set to 0.
In tool axis direction/tool axis normal direction feed (not table-based),
the directions indicated above assume that 0 is set in parameter No.
19698 and No. 19699. When a rotation axis has made a turn or a
nonzero value is set in these parameters in tool axis direction/tool axis
normal direction feed, the relevant directions are inclined accordingly.

12312

States of the manual handle feed axis selection signals when a movement is

made in the second axis direction in tool axis normal direction handle

feed/interrupt and table-based horizontal direction handle feed/interrupt

[Input type] Parameter input

[Data type] Byte path

[Valid data range] 1 to 24

This parameter sets the states of the manual handle feed axis selection
signals (HS1A to HS1E for the first manual handle) or the manual
handle interrupt axis selection signals (HS1IA to HS1IE for the first
manual handle) when a movement is made in the second axis direction.
(For settings, see "Table of correspondence with the manual handle
feed axis selection signals" in the description of parameter No.
12310.)
The handle for which the signal states are set is determined by
parameter No. 12323.

Content .. 278 279 280 281 ..