Porshe 911 (997). Manual - part 487

Adjusting sliding-roof panel

2. Adjust the sliding-roof panel according to the front and rear roof contour to -dimension A- up to -1.0 mm

lower, -dimension B- up to +1.0 mm higher. Tighten fastening screws. Tightening torque → Tightening
torque: 4 ftlb.

Moving sliding-roof panel to tilting position

3. Extend sliding-roof panel to tilting position. Carefully pull slide/tilt sunroof trim forward evenly on

the left and right until it is approx. 40 mm in front of the roof edge cut-out. Check whether the left
and right-hand inner side panels -inset- have engaged.

Moving sliding-roof panel to zero position

Diagnostic system: reading out fault memory and activating systems

Installing cover for sliding roof

2105

4. Move sliding-roof panel to zero position (closed).

Engaging slide/tilt sunroof trim

Note

If inner panels are damaged or have become detached from the groove of the sunroof frame, take off
the slide/tilt sunroof trim with the sliding-roof panel removed and replace the inner panels if
necessary. → 708619 Removing and installing slide/tilt sunroof trim

• 

5. Push slide/tilt sunroof trim forward as far as the roof edge cut-out. While doing so, take care not to push

slide/tilt sunroof trim upwards. This could detach or damage the inner panels.

Closing sliding-roof panel

6. Open sliding-roof panel approx. 80 mm. Pull slide/tilt sunroof forward until the left and right-hand

drivers engage. Close sliding-roof panel.

7. Function test:The slide/tilt sunroof trim lies against the rear of the sliding-roof panel in tilting

position. Close sliding-roof panel. The slide/tilt sunroof trim must lie against the clamping frame of
the roof lining on the front, right and left with a slight degree of pre-tension. The slide/tilt sunroof
trim must not lie against the rear cross bar of the roof lining.
A gap of approx. -0,5 mm- (cheque card thickness) must be left. There is no gap at the rear cross
bar and the roof lining in vehicles with a fully coated (flocked) clamping frame.

997110, 997111, 997120, 997121, 997410, 997411, 997430, 997431

Diagnostic system: reading out fault memory and activating systems

Installing cover for sliding roof

2106

WARNUNG

Gefahr des Verlusts der Text-Bild-Zuordnung beim Ausdruck.

Aus technischen Gründen kann derzeit nicht ausgeschlossen werden, dass trotz
einwandfreier Darstellung auf dem Bildschirm beim Ausdruck der
Zusammenhang von Text und zugehörigem Bild verloren geht.

• 

Wird der Fehler nicht bemerkt, besteht die Gefahr, daß Arbeiten nicht korrekt
durchgeführt werden und es dadurch zu Personen- und Sachschäden kommt.

• 

→ Vergleichen Sie deshalb nach dem Druckvorgang unbedingt die Ausdrucke mit der
Bildschirmdarstellung. Korrigieren Sie die Ausdrucke im Fehlerfall so, daß der Inhalt der
Bildschirmdarstellung zutreffend wiedergegeben wird.

WARNING

Danger of losing text-figure correspondence when printing out.

For technical reasons, it can currently not be ruled out that the correspondence
between text and associated figure can be lost when it is printed out, even though
the display on the screen is correct.

• 

If the fault is not noticed, there is the danger that work will not be performed
correctly which can cause injury and damage.

• 

→ Therefore, always compare printouts with the screen display after printing them out. Correct
the printouts if they are faulty so that the content of the screen display matches that on the
printouts.

AVERTISSEMENT

Risque de perte de la correspondance texte-illustration lors de l'impression papier.

Pour des raisons techniques, il ne peut pas être exclu à l'heure actuelle que, même
en cas d'affichage correct à l'écran, la correspondance entre le texte et l'illustration
puisse être erronée sur l'impression papier.

• 

Si l'erreur passe inaperçue, on court le risque d'exécuter certaines opérations de
manière incorrecte pouvant conduire à des dommages corporels et matériels.

• 

→ Comparez impérativement pour cette raison les impressions papier avec l'affichage à l'écran.
Corrigez-les en cas d'erreur de manière à reproduire correctement l'affichage à l'écran.

ATTENZIONE

Pericolo di perdita dell'abbinamento testo-immagine nella stampa.

Per motivi tecnici non è escluso che, nonostante la rappresentazione sullo schermo

• 

Diagnostic system: reading out fault memory and activating systems

Installing cover for sliding roof

2107

risulti perfetta, durante la stampa venga persa la corrispondenza fra testo e
relativa immagine.
Se tale difetto non viene rilevato vi è il pericolo che i lavori non siano eseguiti
correttamente; ciò può avere come conseguenza lesioni e danneggiamenti.

• 

→ Per questo motivo, dopo la stampa è assolutamente necessario confrontare le stampe con la
rappresentazione sullo schermo. In caso di errore si prega di correggere le stampe, così da
garantire la riproduzione esatta della rappresentazione sullo schermo.

ADVERTENCIA

Al imprimir se corre el riesgo de perder la correcta asignación de las figuras al texto.

Por motivos técnicos, por el momento no se puede descartar que, aun siendo
correcta la imagen que aparezca en la pantalla, al imprimir se pierda la
correlación entre el texto y la figura correspondiente.

• 

Si este error pasara desapercibido, existe el riesgo de que los trabajos no se
ejecuten de forma correcta y, por tanto, se produzcan daños personales y
materiales.

• 

→ Por ello le rogamos que tras el proceso de impresión compare siempre las copias impresas con
la imagen de la pantalla. En caso de error, corrija las copias impresas de forma que se
correspondan con el contenido de la imagen de la pantalla.

Diagnostic system: reading out fault memory and activating systems

Installing cover for sliding roof

2108