Volkswagen Golf / Golf GTI / Jetta. Manual - part 907

01-404

 

  

  

Erase DTC memory

 

  

  

Note:  

  

  

The vehicle V.A.G 1552 System tester can be 
used instead of the V.A.G 1551 scan tool, 
however a print-out is not possible. 

  

  

-  Connecting scan tool 

 

Page 01-3

 , initiating On 

Board Diagnostic (OBD) 

 

Page 01-395

 . 

  

  

Prerequisites:  

  

  

 DTCs are repaired 

  

  

 Functional check has been carried out 

  

  

 DTC memory checked again 

Rapid data transfer 

HELP

Select function XX

     Indicated on display:  

-  Press buttons -0- and -5- (the function "Erase 

DTC memory" is entered with 05). 

Rapid data transfer 

Q

05 Erase DTC memory

     Indicated on display:  

-  Confirm entry with the -Q- button. 

Rapid data transfer 

DTC memory is erased!

     Indicated on display:  

-  Press 

button. 

Driver's side seat adjustment, On Board Diagnostic (OBD)

13/2/2005

01-405

 

Rapid data transfer 

HELP

Select function XX

     Indicated on display:  

Note:  

WARNING! 

DTC memory was not checked

    

 If this appears in the display, the 

test sequence is faulty. 

 Adhere strictly to test sequence; 

first of all check DTC memory, 
then erase memory. 

-  Press buttons -0- and -6- to end 

the output. 

Rapid data transfer 

Q

06 End output

     Indicated on display:  

-  Confirm entry with the -Q- button. 

Rapid data transfer 

HELP

Enter address word XX

     Indicated on display:  

-  Switch off ignition. 

-  Disconnect connector to V.A.G 

1551 scan tool. 

Driver's side seat adjustment, On Board Diagnostic (OBD)

13/2/2005

01-406

 

  

  

End Output

 

  

  

-  Press buttons -0- and -6- to end 

the output. 

Rapid data transfer 

Q

06 End output

     Indicated on display:  

-  Confirm entry with the -Q- button. 

Rapid data transfer 

HELP

Enter address word XX

     Indicated on display:  

-  Switch off ignition. 

-  Disconnect connector to V.A.G 

1551 scan tool. 

Driver's side seat adjustment, On Board Diagnostic (OBD)

13/2/2005

01-407

 

  

  

DTC table

 

  

  

Note:  

  

  

 The DTC table is listed according to the 5 digit 

code on the left. 

  

  

 Explanation of the malfunction types (e.g. "open 

circuit/short circuit to Ground"): 

  

  

 Scan tool operating instructions 

  

  

 Before replacing components indicated as 

malfunctioning, check the wiring and 
connectors to these components as well as the 
Ground connections using wiring diagram. This 
is particularly relevant if malfunctions are output 
as "occurring sporadically" (SP). 

  

  

 The malfunctions displayed can be localized 

using the test table. 

  

  

 This malfunction "no communication" can also 

appear with the door control modules. This has 
no influence on the function of the convenience 
system and is therefore of no consequence. 
Erase DTC memory. 

00668 049

Vehicle system voltage terminal 30

Signal too high

     Scan tool print out: The number 049 (e.g.) shown 

here in bold is not relevant.  

Driver's side seat adjustment, On Board Diagnostic (OBD)

13/2/2005