Volkswagen Golf / Golf GTI / Jetta. Manual - part 1199

91-96

 

  

  

-  Where applicable, carefully record the 8 

character Station Identification (STID) number 
and Electronic Serial Number (ESN) from labels 
on replacement module. 

  

  

-  Connect VAS 5051 with adapter cable to Data 

Link Connector (DLC) and select mode "Guided 
Fault Finding" 

  

  

-  Enter appropriate model, equipment and model 

year information and press ">" to confirm. 

  

   After all Control Modules have been registered 

and DTC memories checked, see "Continued for 
all" 

 

Page 91-96

 .  

  

   If the STID number and ESN DO NOT appear 

on labels on the new control module, proceed 
as follows: 

  

  

-  Select "Go to" 

  

  

-  Select "Function / Component Selection" 

  

  

-  Select "Body (Repair Group 01; 27; 50 to 97"  

  

  

-  Select "Electrical System (Repair Group 27; 90 

to 97) 

  

  

-  Select "01-Systems capable of self-diagnosis" 

  

  

-  Select "Telematics NAR" 

  

  

-  Select "Functions - Telematics NAR" and press 

">" to confirm. 

  

  

-  Select "Check control module versions - 

Telematics NAR". 

  

  

-  Record ESN and STID number from appropriate 

display fields. 

Telematics

13/2/2005

91-97

 

  

   Continued for all:  

  

  

-  Select "Go to" 

  

  

-  Select "Function / Component Selection" 

  

  

-  Select "Body (Repair Group 01; 27; 50 to 97"  

  

  

-  Select "Electrical System (Repair Group 27; 90 

to 97) 

  

  

-  Select "01-Systems capable of self-diagnosis" 

  

  

-  Select "Telematics NAR" 

  

  

-  Select "Functions - Telematics NAR" and press 

">" to confirm. 

  

  

-  Select "check/erase DTC memory Telematics 

NAR" 

  

  

-  Switch off ignition and wait a few moments. 

  

  

-  Switch on ignition. 

  

  

-  Enter address word 75 - "Telematics" 

  

  

-  Select "Go to" 

  

  

-  Select "Function / Component Selection" 

  

  

-  Select "Body (Repair Group 01; 27; 50 to 97"  

  

  

-  Select "Electrical System (Repair Group 27; 90 

to 97) 

  

  

-  Select "01-Systems capable of self-diagnosis" 

Telematics

13/2/2005

91-98

 

  

  

-  Select "Telematics NAR" 

  

  

-  Select "Functions - Telematics NAR" and press 

">" to confirm. 

  

  

-  Select "check DTC memory - Telematics 

NAR". 

  

   No DTCs must be present.  

  

  

-  Check and confirm the green telematics 

indicator lamp in Telematics Control Head is on. 

  

  

-  Exit operating mode "Guided Fault Finding".  

  

  

-  Disconnect VAS 5051 from DLC. 

  

   Reconfiguration  

  

  

-  Drive vehicle outside to area away from tall 

buildings, and with no overhead obstructions 
(trees, bridges, etc.). 

  

  

- 

Press the blue OnStar

 ("On

") button. A 

recorded introduction will be heard. 

  

  

- 

Press the "On

" button again at any time 

during the recording (it is not necessary to wait 
for the recording to finish). 

  

  

-  When an OnStar

call center advisor answers, 

identify yourself as an Volkswagen Technician, 
and that you have replaced the "Vehicle 
Communications Interface Unit (VCIM)". 

  

  

-  Supply advisor with STID number and ESN from 

new module. Supply the VIN and customer 
details if necessary. The advisor will guide you 
through the system reconfiguration and update 
of the customer's account. 

Telematics

13/2/2005

91-99

 

  

  

-  When reconfiguration is complete, end call by 

pressing the Communications ("DOT") button. 

  

  

- 

Wait ten minutes and press the "On

" button 

again to verify system operation. Inform call 
center advisor you are an Volkswagen 
Technician performing a quality check after 
VCIM replacement/system reconfiguration. 

  

  

-  End call by pressing the Communications 

("DOT") button. 

  

   Notes:  

  

  

 Normal connection time is 10 - 15 seconds. 

However, depending on local cellular/GPS 
conditions, making a connection could take up 
to three minutes. Be patient. 

  

  

 If the message: "unable to contact OnStar" is 

heard, try relocating vehicle to a more elevated 
or open area and repeat connection attempts. 
Depending on the local cellular/GPS traffic 
conditions, several connection attempts may be 
necessary (and are normal). 

  

  

 If the message: "OnStar request ended" is 

heard, the cellular connection was interrupted 
before the connection was completed. Wait for 
a short period of time before repeating 
connection attempt. 

  

  

 If you are still unable to connect, call OnStar

Customer Care at 1-888-390-4050. The 

advisor will verify the customer's OnStar

 

account is active. 

Telematics

13/2/2005