Nissan Frontier D40. Manual - part 943

 

  Index      Nissan     Nissan Frontier D40 (2010 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  941  942  943  944   ..

 

 

Nissan Frontier D40. Manual - part 943

 

 

RF-56

< ON-VEHICLE REPAIR >

SUNROOF SYSTEM

1.

Remove the headlining. Refer to 

INT-24, "Removal and Installation"

.

2.

Visually check the drain hoses for proper connections, damage or deterioration.

3.

Remove each drain hose and check visually for damage, cracks or deterioration.

4.

Pour water through the drain hose to check for damage.

• If any damage is found, replace the drain hose.

Installation

Installation is in the reverse order of removal.

WEATHERSTRIP

Visually check weatherstrip for any damage, deterioration, or flattening. 
• In the case of wind or water leakage around glass lid area, close glass lid and pour water around it to find the

damaged or gaped portion.

• If any damage is found, inspect and repair the body sealing surface, replace sunroof lid seal, or replace

glass lid assembly. Refer to GLASS LID in this section.

CAUTION:

Do not remove weatherstrip from glass lid.

LINK AND WIRE ASSEMBLY

NOTE:
Before replacing any suspect part, be sure it is the source of the noise.
1.

Visually check to determine if a sufficient amount of petroleum jelly has been applied to the wire or rail
groove. If not, add petroleum jelly as required.

2.

Check wire for any damage or deterioration. If any damage is found, remove rear guide, then replace
wire.

LIIA0272E

RSU-1

SUSPENSION

C

D

F

G

H

I

J

K

L

M

SECTION 

RSU

A

B

RSU

N

O

P

CONTENTS

REAR SUSPENSION

PRECAUTION ...............................................

2

PRECAUTIONS ...................................................

2

Precaution for Supplemental Restraint System 
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" .................................................................
..

2

Precaution for Rear Suspension  ...............................

2

PREPARATION ............................................

3

PREPARATION ...................................................

3

Commercial Service Tool  ..........................................

3

SYMPTOM DIAGNOSIS  ...............................

4

NOISE, VIBRATION, AND HARSHNESS 
(NVH) TROUBLESHOOTING  .............................

4

NVH Troubleshooting Chart  ......................................

4

ON-VEHICLE MAINTENANCE .....................

5

REAR SUSPENSION ASSEMBLY  .....................

5

On-Vehicle Inspection and Service  ...........................

5

ON-VEHICLE REPAIR ..................................

6

REAR SUSPENSION ASSEMBLY ....................

6

Component ...............................................................

6

REMOVAL AND INSTALLATION  ................

8

SHOCK ABSORBER  .........................................

8

Removal and Installation  ..........................................

8

Disposal ....................................................................

8

LEAF SPRING ....................................................

9

Removal and Installation  ..........................................

9

SERVICE DATA AND SPECIFICATIONS 
(SDS) ............................................................

12

SERVICE DATA AND SPECIFICATIONS 
(SDS) .................................................................

12

General Specification (Rear)  ...................................

12

Wheelarch Height (Unladen*1) ................................

12

RSU-2

< PRECAUTION >

PRECAUTIONS

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT 
PRE-TENSIONER"

INFOID:0000000005549829

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.

WARNING:

• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.

• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this

Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-

tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.

• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the

battery, and wait at least 3 minutes before performing any service.

Precaution for Rear Suspension

INFOID:0000000005275395

• When installing the rubber bushings, the final tightening must be done under unladen condition and with the

tires on level ground. Oil will shorten the life of the rubber bushings, so wipe off any spilled oil immediately.

• Unladen condition means the fuel tank, engine coolant and lubricants are at the full specification. The spare

tire, jack, hand tools, and mats are in their designated positions. There are no passengers in the vehicle.

• After installing suspension components, check the wheel alignment.
• Caulking nuts are not reusable. Always use new caulking nuts for installation. New caulking nuts are pre-

oiled, do not apply any additional lubrication.

PREPARATION

RSU-3

< PREPARATION >

C

D

F

G

H

I

J

K

L

M

A

B

RSU

N

O

P

PREPARATION

PREPARATION

Commercial Service Tool

INFOID:0000000005275396

Tool name

Description

Power tool

Removing bolts and nuts

PBIC0190E

 

 

 

 

 

 

 

Content   ..  941  942  943  944   ..