Nissan Quest E52. Manual - part 411

 

  Index      Nissan     Nissan Quest E52 (2011-2014 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

  

 

Content   ..  409  410  411  412   ..

 

 

Nissan Quest E52. Manual - part 411

 

 

DLK-358

< DTC/CIRCUIT DIAGNOSIS >

AUTOMATIC SLIDING DOOR MOTOR

AUTOMATIC SLIDING DOOR MOTOR

SLIDING DOOR LH

SLIDING DOOR LH : Diagnosis Procedure

INFOID:0000000009649311

1.

CHECK AUTOMATIC SLIDING DOOR MOTOR INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect sliding door control unit LH connector.

3.

Check voltage between sliding door control unit LH harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace sliding door control unit LH. Refer to 

DLK-500, "LH : Removal and Installation"

.

2.

CHECK AUTOMATIC SLIDING DOOR MOTOR CIRCUIT

1.

Disconnect automatic sliding door unit LH connector.

2.

Check continuity between sliding door control unit LH harness connector and automatic sliding door unit
LH harness connector.

3.

Check continuity between sliding door control unit LH harness connector and ground.

Is the inspection result normal?

YES

>> Replace automatic sliding door unit LH.

NO

>> Repair or replace harness.

SLIDING DOOR RH

SLIDING DOOR RH : Diagnosis Procedure

INFOID:0000000009649312

1.

CHECK AUTOMATIC SLIDING DOOR MOTOR INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect sliding door control unit RH connector.

3.

Check voltage between sliding door control unit RH harness connector and ground.

(+)

(–)

Condition

Voltage

Sliding door control unit LH

 Connector

Terminal

B47

43

Ground

Sliding door LH

Open operate

9 – 16 V

46

Close operate

Sliding door control unit LH

Automatic sliding door unit LH

Continuity 

 Connector

Terminal

 Connector

Terminal

B47

43

B33

3

Existed

46

4

Sliding door control unit LH

Ground

Continuity 

 Connector

Terminal

B47

43

Not existed

46

(+)

(–)

Condition

Voltage

Sliding door control unit RH

 Connector

Terminal

B249

43

Ground

Sliding door RH

Open operate

9 – 16 V

46

Close operate

AUTOMATIC SLIDING DOOR MOTOR

DLK-359

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace sliding door control unit RH. Refer to 

DLK-500, "LH : Removal and Installation"

.

2.

CHECK AUTOMATIC SLIDING DOOR MOTOR CIRCUIT

1.

Disconnect automatic sliding door unit RH connector.

2.

Check continuity between sliding door control unit RH harness connector and automatic sliding door unit
RH harness connector.

3.

Check continuity between sliding door control unit RH harness connector and ground.

Is the inspection result normal?

YES

>> Replace automatic sliding door unit RH.

NO

>> Repair or replace harness.

Sliding door control unit RH

Automatic sliding door unit RH

Continuity 

 Connector

Terminal

 Connector

Terminal

B249

43

B245

4

Existed

46

3

Sliding door control unit RH

Ground

Continuity 

 Connector

Terminal

B249

43

Not existed

46

DLK-360

< DTC/CIRCUIT DIAGNOSIS >

SLIDING DOOR LOCK RELEASE ACTUATOR

SLIDING DOOR LOCK RELEASE ACTUATOR

SLIDING DOOR LH

SLIDING DOOR LH : Diagnosis Procedure

INFOID:0000000009649313

1.

CHECK SLIDING DOOR LOCK RELEASE ACTUATOR INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect sliding door lock release actuator LH connector.

3.

Check voltage between sliding door lock release actuator LH harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> GO TO 4.

2.

CHECK SLIDING DOOR LOCK RELEASE ACTUATOR CIRCUIT

1.

Disconnect sliding door control unit LH connector.

2.

Check continuity between sliding door control unit LH harness connector and sliding door lock release
actuator LH harness connector.

3.

Check continuity between sliding door control unit LH harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK SLIDING DOOR LOCK RELEASE ACTUATOR CIRCUIT 2

1.

Connect sliding door control unit LH connector and sliding door lock release actuator LH connector.

2.

Check voltage between sliding door control unit LH harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace sliding door control unit LH. Refer to 

DLK-500, "LH : Removal and Installation"

.

4.

CHECK SLIDING DOOR LOCK RELEASE ACTUATOR GROUND CIRCUIT

1.

Disconnect sliding door control unit LH connector.

2.

Check continuity between sliding door control unit LH harness connector and sliding door lock release
actuator LH harness connector.

(+)

(–)

Voltage

Sliding door lock release actuator LH

 Connector

Terminal

D121

1

Ground

9 – 16 V

Sliding door control unit LH

Sliding door lock release actuator LH

Continuity 

 Connector

Terminal

 Connector

Terminal

B46

39

D121

2

Existed

Sliding door control unit LH

Ground

Continuity 

 Connector

Terminal

B46

39

Not existed

(+)

(–)

Voltage

Sliding door control unit LH

 Connector

Terminal

B46

39

Ground

0 V

SLIDING DOOR LOCK RELEASE ACTUATOR

DLK-361

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

3.

Check continuity between sliding door control unit LH harness connector and ground.

Is the inspection result normal?

YES

>> Replace sliding door control unit LH. Refer to 

DLK-500, "LH : Removal and Installation"

.

NO

>> Repair or replace harness.

5.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-42, "Intermittent Incident"

.

>> INSPECTION END

SLIDING DOOR RH

SLIDING DOOR RH : Diagnosis Procedure

INFOID:0000000009649314

1.

CHECK SLIDING DOOR LOCK RELEASE ACTUATOR INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect sliding door lock release actuator RH connector.

3.

Check voltage between sliding door lock release actuator RH harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> GO TO 4.

2.

CHECK SLIDING DOOR LOCK RELEASE ACTUATOR CIRCUIT

1.

Disconnect sliding door control unit RH connector.

2.

Check continuity between sliding door control unit RH harness connector and sliding door lock release
actuator RH harness connector.

3.

Check continuity between sliding door control unit RH harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK SLIDING DOOR LOCK RELEASE ACTUATOR CIRCUIT 2

1.

Connect sliding door control unit RH connector and sliding door lock release actuator RH connector.

Sliding door control unit LH

Sliding door lock release actuator LH

Continuity 

 Connector

Terminal

 Connector

Terminal

B46

40

D121

1

Existed

Sliding door control unit LH

Ground

Continuity 

 Connector

Terminal

B46

40

Not existed

(+)

(–)

Voltage

Sliding door lock release actuator RH

 Connector

Terminal

D122

1

Ground

9 – 16 V

Sliding door control unit RH

Sliding door lock release actuator RH

Continuity 

 Connector

Terminal

 Connector

Terminal

B248

39

D122

2

Existed

Sliding door control unit RH

Ground

Continuity 

 Connector

Terminal

B248

39

Not existed

 

 

 

 

 

 

 

Content   ..  409  410  411  412   ..