Nissan Versa Note. Manual - part 833

TM-212

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

P285A CLUTCH B PRESSURE

4. Stop the vehicle.

5. Check the first trip DTC.
Is “P285A” detected?

YES

>> Go to 

TM-212, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009019754

1.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-41, "Intermittent Incident"

. 

Is the inspection result normal?

YES 

>> Replace transaxle assembly. Refer to 

TM-252, "Removal and Installation"

.

NO

>> Repair or replace malfunctioning parts.

Selector lever

: “L” POSITION

Accelerator pedal position

: 0.7/8 or more

Vehicle speed

: 10 km/h (6 MPH) or more

MAIN POWER SUPPLY AND GROUND CIRCUIT

TM-213

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

MAIN POWER SUPPLY AND GROUND CIRCUIT

Diagnosis Procedure

INFOID:0000000009019755

1.

CHECK TCM POWER CIRCUIT (PART 1)

1. Turn ignition switch OFF.

2. Disconnect TCM connector.

3. Check voltage between TCM harness connector terminals and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> GO TO 4.

2.

CHECK TCM POWER CIRCUIT (PART 2)

Check voltage between TCM harness connector terminals and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 5.

3.

CHECK TCM GROUND CIRCUIT

Check continuity between TCM harness connector terminals and ground.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

NO

>> Repair or replace malfunctioning parts.

4.

DETECT MALFUNCTION ITEMS (PART 1)

Check the following items:

• Open circuit or short circuit in harness between battery positive terminal and TCM connectors terminals 45,

and 46.

• 10A fuse (No.33, fuse and fusible link block). Refer to 

PG-59, "Terminal Arrangement"

.

Is the inspection result normal?

YES 

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

NO

>> Repair or replace malfunctioning parts.

+

−

Voltage

TCM

Connector

Terminal

F44

45

Ground

10 – 16 V

46

+

−

Condition

Voltage

TCM

Connector

Terminal

F44

47

Ground

Ignition switch ON

10 – 16 V

Ignition switch OFF

Approx. 0 V

48

Ignition switch ON

10 – 16 V

Ignition switch OFF

Approx. 0 V

TCM

—

Continuity

Connector

Terminal

F44

41

Ground

Existed

42

TM-214

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

MAIN POWER SUPPLY AND GROUND CIRCUIT

5.

CHECK CIRCUIT BETWEEN IPDM E/R AND TCM

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R connector.

3. Check continuity between IPDM E/R harness connector terminal and TCM harness connector terminals.

Is the check result normal?

YES

>> GO TO 6.

NO

>> Repair or replace malfunctioning parts.

6.

DETECT MALFUNCTIONING ITEMS (PART 2)

Check the following items:

• Open circuit or short circuit in harness between ignition switch and IPDM E/R. Refer to 

PG-17, "Wiring Dia-

gram — Ignition Power Supply —"

.

• Short circuit in harness between IPDM E/R harness connector terminal 21 and TCM harness connector ter-

minal 47, and 48.

• 10A fuse (No.49, IPDM E/R). Refer to 

PG-60, "IPDM E/R Terminal Arrangement"

.

• IPDM E/R
Is the check result normal?

YES

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

NO

>> Repair or replace malfunctioning parts.

IPDM E/R

TCM

Continuity

Connector

Terminal

Connector

Terminal

E45

21

F44

47

Existed

48

OVERDRIVE CONTROL SWITCH

TM-215

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

OVERDRIVE CONTROL SWITCH

Component Function Check

INFOID:0000000009019756

1.

CHECK OD OFF INDICATOR LAMP FUNCTION

Check OD OFF indicator lamp turns ON for approx. 2 seconds when ignition switch turns ON.
Is the inspection results normal?

YES

>> GO TO 2.

NO

>> Go to 

TM-217, "Diagnosis Procedure"

.

2.

CHECK OVERDRIVE CONTROL SWITCH FUNCTION

1. Shift the selector lever to “D” position.

2. Check that OD OFF indicator lamp turns ON/OFF when overdrive control switch is operated.
Is the inspection results normal?

YES

>> INSPECTION END

NO

>> Go to 

TM-215, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009019757

1.

CHECK OVERDRIVE CONTROL SWITCH CIRCUIT 

1. Turn ignition switch OFF.

2. Disconnect CVT shift selector connector.

3. Turn ignition switch ON.

4. Check voltage between CVT shift selector harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> GO TO 4.

2.

CHECK OVERDRIVE CONTROL SWITCH

Check overdrive control switch. Refer to 

TM-216, "Component Inspection (Overdrive Control Switch)"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace malfunctioning parts.

3.

CHECK GROUND CIRCUIT

Check continuity between CVT shift selector harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace malfunctioning parts.

4.

CHECK CIRCUIT BETWEEN COMBINATION METER AND CVT SHIFT SELECTOR (PART 1)

1. Turn ignition switch OFF.

2. Disconnect combination meter connector.

3. Check continuity between combination meter harness connector terminal and CVT shift selector harness

connector terminal.

CVT shift selector

Voltage

(Approx.)

Connector

+

−

Terminal

M38

1

2

5 V

CVT shift selector

—

Continuity

Connector

Terminal

M38

2

Ground

Existed