Nissan Versa Note. Manual - part 709

 

  Index      Nissan     Nissan Versa Note (2014 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

  

 

Content   ..  707  708  709  710   ..

 

 

Nissan Versa Note. Manual - part 709

 

 

B210C STARTER CONTROL RELAY

SEC-115

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

3.

CHECK STARTER CONTROL RELAY CONTROL CIRCUIT CONTINUITY

1. Disconnect IPDM E/R connector E44 and clutch interlock switch connector E34.

2. Check continuity between IPDM E/R connector E44 and clutch interlock switch connector E34.

3. Disconnect BCM connector M98.

4. Check continuity between IPDM E/R connector E44 and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-70, "Removal and Installation"

.

NO

>> Repair or replace harness or connectors.

4.

CHECK STARTER CONTROL RELAY CONTROL CIRCUIT CONTINUITY

1. Disconnect IPDM E/R connector F42 and transmission range switch connector F52.

2. Check continuity between IPDM E/R connector F42 and transmission range switch connector F52.

3. Disconnect BCM connector M98.

4. Check continuity between IPDM E/R connector F42 and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-70, "Removal and Installation"

.

NO

>> Repair or replace harness or connectors.

IPDM E/R

Clutch interlock switch

Continuity

Connector

Terminal

Connector

Terminal

E44

13

E34

2

Yes

IPDM E/R

Ground

Continuity

Connector

Terminal

E44

13

—

No

IPDM E/R

Transmission range switch

Continuity

Connector

Terminal

Connector

Terminal

F42

40

F52

10

Yes

IPDM E/R

Ground

Continuity

Connector

Terminal

F42

40

—

No

SEC-116

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B210D STARTER RELAY

B210D STARTER RELAY

DTC Logic

INFOID:0000000009705928

DTC DETECTION LOGIC

NOTE:

If DTC B210D is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to 

BCS-

60, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION

1. Turn ignition switch ON.

2. Turn ignition switch OFF and wait 1 second or more.

3. Turn ignition switch ON.

4. Perform Self Diagnostic Result of IPDM E/R using CONSULT.
Is DTC B210D displayed?

YES

>> Refer to 

SEC-116, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000009705929

Regarding Wiring Diagram information, refer to 

SEC-40, "Wiring Diagram"

.

1.

 PERFORM SELF DIAGNOSTIC RESULT

Perform Self Diagnostic Result of IPDM E/R using CONSULT.
Is display history of DTC B210D CRNT?

YES

>> GO TO 2.

NO

>> Refer to 

GI-41, "Intermittent Incident"

.

2.

CHECK STARTER CONTROL RELAY CONTROL CIRCUITS VOLTAGE

Check voltage between IPDM E/R connectors and ground.

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-31, "Removal and Installation"

.

NO (WITH M/T)>>GO TO 3.

NO (WITH CVT)>>GO TO 4.

3.

CHECK STARTER CONTROL RELAY CONTROL CIRCUIT CONTINUITY

1. Disconnect IPDM E/R connectors E44, BCM connector M98, clutch interlock switch connector E34.

CONSULT Display

DTC Detection Condition

Possible Cause

STARTER RLY ON CIRC
[B210D]

When comparing the following items, IPDM E/R 
detects that starter control relay is stuck in the 
ON position for 5 second or more.
• Starter control relay signal (CAN) from BCM
• Starter relay status signal (CAN) from BCM
• Starter control relay and starter relay status 

signal (IPDM E/R input)

• Starter control relay control signal (IPDM E/R 

output)

• Harness or connectors (starter motor relay 

control circuit open or short)

• IPDM E/R
• BCM

IPDM E/R

Ground

Voltage

(Approx.)

Connector

Terminal

E44

13

—

Battery voltage

F42

40

B210D STARTER RELAY

SEC-117

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

2. Check continuity between IPDM E/R connector E44 and ground.

Is the inspection result normal?

YES

>> Refer to 

SEC-96, "Diagnosis Procedure"

.

NO

>> Repair or replace harness or connectors.

4.

CHECK STARTER CONTROL RELAY CONTROL CIRCUIT CONTINUITY

1. Disconnect IPDM E/R connectors F42, BCM connector M98, transmission range switch connector F52.

2. Check continuity between IPDM E/R connector F42 and ground.

Is the inspection result normal?

YES

>> Refer to 

SEC-96, "Diagnosis Procedure"

.

NO

>> Repair or replace harness or connectors.

IPDM E/R

Ground

Continuity

Connector

Terminal

E44

13

—

No

IPDM E/R

Ground

Continuity

Connector

Terminal

F42

40

—

No

SEC-118

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B210E STARTER RELAY

B210E STARTER RELAY

DTC Logic

INFOID:0000000009705930

DTC DETECTION LOGIC

NOTE:

• If DTC B210E is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

BCS-60, "DTC Logic"

.

• If DTC B210E is displayed with DTC B2605, first perform the trouble diagnosis for DTC B2605. Refer to

SEC-94, "DTC Logic"

.

• When IPDM E/R power supply voltage is low (Approx. 7 - 8 V for about 1 second), the DTC B210F may be

detected.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION

1. Turn ignition switch ON.

2. Turn ignition switch OFF and wait 1 second or more.

3. Turn ignition switch ON.

4. Perform Self Diagnostic Result of IPDM E/R using CONSULT.
Is DTC B210E displayed?

YES

>> Refer to 

SEC-118, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000009705931

Regarding Wiring Diagram information, refer to 

SEC-40, "Wiring Diagram"

.

1.

 PERFORM SELF DIAGNOSTIC RESULT

Perform Self Diagnostic Result of IPDM E/R using CONSULT.
Is display history of DTC B210E CRNT?

YES

>> GO TO 2.

NO

>> Refer to 

GI-41, "Intermittent Incident"

.

2.

CHECK STARTER CONTROL RELAY CONTROL CIRCUITS VOLTAGE

Check voltage between IPDM E/R connectors and ground.

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-31, "Removal and Installation"

.

NO (WITH M/T)>>GO TO 3.

CONSULT Display

DTC Detection Condition

Possible Cause

STARTER RELAY OFF
[B210E]

When comparing the following items, IPDM E/R 
detects that starter control relay is stuck in the 
OFF position for 5 second or more.
• Starter control relay signal (CAN) from BCM
• Starter relay status signal (CAN) from BCM
• Starter control relay and starter relay status 

signal (IPDM E/R input)

• Starter control relay control signal (IPDM E/R 

output)

• IPDM E/R
• BCM
• Battery

IPDM E/R

Ground

Voltage

(Approx.)

Connector

Terminal

E44

13

—

Battery voltage

F42

40

 

 

 

 

 

 

 

Content   ..  707  708  709  710   ..