Nissan Versa Note. Manual - part 623

PCS-102

< REMOVAL AND INSTALLATION >

[POWER DISTRIBUTION SYSTEM]

BCM (BODY CONTROL MODULE)

REMOVAL AND INSTALLATION

BCM (BODY CONTROL MODULE)

Removal and Installation

INFOID:0000000009579035

For removal and installation of the BCM (Body Control Module), refer to 

BCS-70, "Removal and Installation"

.

PCS

PUSH-BUTTON IGNITION SWITCH

PCS-103

< REMOVAL AND INSTALLATION >

[POWER DISTRIBUTION SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

PUSH-BUTTON IGNITION SWITCH

Removal and Installation

INFOID:0000000009579036

REMOVAL

1. Remove NATS antenna amp. Refer to 

SEC-181, "Removal and Installation"

.

2. Release pawls and remove the push-button ignition switch (1).

: Pawl 

INSTALLATION

Installation is in the reverse order of removal.

ALKIA3180ZZ

PG

PG-1

ELECTRICAL & POWER CONTROL

C

D

E

F

G

H

I

J

K

L

B

SECTION 

PG

A

O

P

N

CONTENTS

POWER SUPPLY, GROUND & CIRCUIT ELEMENTS

PRECAUTION ...............................................

3

PRECAUTIONS ...................................................

3

Precaution for Supplemental Restraint System 
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...................................................................

3

PREPARATION ............................................

4

PREPARATION ...................................................

4

Special Service Tools ................................................

4

Commercial Service Tool  ..........................................

4

DTC/CIRCUIT DIAGNOSIS  ..........................

5

POWER SUPPLY ROUTING CIRCUIT ...............

5

Wiring Diagram — Battery Power Supply — .............

5

Wiring Diagram — Accessory Power Supply —  .....

13

Wiring Diagram — Ignition Power Supply —  ..........

17

Fuse ........................................................................

25

Fusible Link  .............................................................

25

GROUND ............................................................

26

Ground Distribution  .................................................

26

HARNESS ..........................................................

33

Harness Layout  .......................................................

33

ELECTRICAL UNITS LOCATION ......................

49

Electrical Units Location ..........................................

49

HARNESS CONNECTOR ..................................

53

Description ..............................................................

53

STANDARDIZED RELAY  ..................................

56

Description ..............................................................

56

FUSE BLOCK - JUNCTION BOX (J/B)  .............

58

Terminal Arrangement  ............................................

58

FUSE, FUSIBLE LINK AND RELAY BOX .........

59

Terminal Arrangement  ............................................

59

IPDM E/R (INTELLIGENT POWER DISTRI-
BUTION MODULE ENGINE ROOM)  ................

60

IPDM E/R Terminal Arrangement ............................

60

BASIC INSPECTION  ...................................

61

BATTERY ..........................................................

61

How to Handle Battery .............................................

61

Work Flow ................................................................

61

INSPECTION AND ADJUSTMENT  ..................

64

ADDITIONAL SERVICE WHEN REMOVING BAT-
TERY NEGATIVE TERMINAL  ...................................

64

ADDITIONAL SERVICE WHEN REMOVING 
BATTERY NEGATIVE TERMINAL : Special Re-
pair Requirement  .....................................................

64

FUSE INSPECTION  ..........................................

65

How To Check  .........................................................

65

FUSIBLE LINK INSPECTION  ...........................

66

How To Check  .........................................................

66

REMOVAL AND INSTALLATION ...............

67

BATTERY ..........................................................

67

Exploded View .........................................................

67

Removal and Installation (Battery)  ..........................

67

Removal and Installation (Battery Tray)  ..................

68

BATTERY TERMINAL WITH FUSIBLE LINK ...

69

Exploded View .........................................................

69

Removal and Installation  .........................................

69

BATTERY CURRENT SENSOR  .......................

70

Exploded View .........................................................

70

Removal and Installation  .........................................

70

SERVICE DATA AND SPECIFICATIONS 
(SDS) ............................................................

71

PG-2

SERVICE DATA AND SPECIFICATIONS 
(SDS) ..................................................................

71

Battery .....................................................................

71