Nissan Versa Note. Manual - part 208

IGN OFF INTERLOCK DOOR UNLOCK FUNCTION DOES NOT OPERATE

DLK-117

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

IGN OFF INTERLOCK DOOR UNLOCK FUNCTION DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000009645254

1.

CHECK AUTOMATIC LOCK/UNLOCK SELECT SETTING IN WORK SUPPORT

1. Select DOOR LOCK of BCM using CONSULT.

2. Select AUTOMATIC LOCK/UNLOCK SELECT in WORK SUPPORT mode.

3. Check AUTOMATIC LOCK/UNLOCK SELECT setting in WORK SUPPORT.

Refer to 

BCS-16, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Set Unlock Only or Lock/Unlock in AUTOMATIC LOCK/UNLOCK SELECT.

2.

CHECK AUTOMATIC DOOR UNLOCK SELECT SETTING IN WORK SUPPORT

1. Select DOOR LOCK of BCM using CONSULT.

2. Select AUTOMATIC DOOR UNLOCK SELECT in WORK SUPPORT mode.

3. Check AUTOMATIC DOOR UNLOCK SELECT setting in WORK SUPPORT.

Refer to 

BCS-16, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Set MODE 1 or MODE 3 in AUTOMATIC DOOR UNLOCK SELECT.

3.

REPLACE BCM

1. Replace BCM. Refer to 

BCS-70, "Removal and Installation"

.

2. Confirm the operation after replacement.
Is the result normal?

YES

>> Inspection End.

NO

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

DLK-118

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

HAZARD AND BUZZER REMINDER DOES NOT OPERATE

HAZARD AND BUZZER REMINDER DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000009645255

1.

CHECK HAZARD ANSWER BACK SETTING IN WORK SUPPORT

1. Select INTELLIGENT KEY of BCM using CONSULT.

2. Select HAZARD ANSWER BACK in WORK SUPPORT mode.

3. Check the HAZARD ANSWER BACK setting in WORK SUPPORT.

Refer to 

BCS-20, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Set the Lock Only, Unlock Only or Lock/Unlock in HAZARD ANSWER BACK.

2.

CHECK ANS BACK I-KEY LOCK SETTING IN WORK SUPPORT

1. Select INTELLIGENT KEY of BCM using CONSULT.

2. Select ANS BACK I-KEY LOCK in WORK SUPPORT mode.

3. Check the ANS BACK I-KEY LOCK setting in WORK SUPPORT.

Refer to 

BCS-20, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Set the Horn Chirp or Buzzer in ANS BACK I-KEY LOCK.

3.

CHECK ANS BACK I-KEY UNLOCK SETTING IN WORK SUPPORT

1. Select INTELLIGENT KEY of BCM using CONSULT.

2. Select ANS BACK I-KEY UNLOCK in WORK SUPPORT mode.

3. Check the ANS BACK I-KEY UNLOCK setting in WORK SUPPORT.

Refer to 

BCS-20, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Set the On in ANS BACK I-KEY UNLOCK.

4.

CHECK HAZARD FUNCTION

Check hazard function.

Refer to 

DLK-98, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace the malfunctioning parts.

5.

CHECK INTELLIGENT KEY WARNING BUZZER

Check Intelligent Key warning buzzer.

Refer to 

DLK-99, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace the malfunctioning parts.

6.

REPLACE BCM

1. Replace BCM. Refer to 

BCS-70, "Removal and Installation"

.

2. Confirm the operation after replacement. 
Is the result normal?

YES

>> Inspection End.

NO

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

KEY REMINDER FUNCTION DOES NOT OPERATE

DLK-119

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

KEY REMINDER FUNCTION DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000009645256

1.

CHECK ANTI KEY LOCK IN FUNCTI SETTING IN WORK SUPPORT

1. Select INTELLIGENT KEY of BCM using CONSULT.

2. Select ANTI KEY LOCK IN FUNCTI in WORK SUPPORT mode.

3. Check ANTI KEY LOCK IN FUNCTI setting in WORK SUPPORT.

Refer to 

BCS-20, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Set On in ANTI KEY LOCK IN FUNCTI.

2.

CHECK DOOR SWITCH

Check door switch.

Refer to 

DLK-95, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CHECK INSIDE KEY ANTENNA

Check inside key antenna.

• Instrument center: Refer to 

DLK-64, "DTC Logic"

.

• Console: Refer to 

DLK-66, "DTC Logic"

.

• Trunk room: Refer to 

DLK-68, "DTC Logic"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the malfunctioning parts.

4.

CHECK UNLOCK SENSOR

Check unlock sensor.

Refer to 

DLK-88, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace the malfunctioning parts.

5.

REPLACE BCM

1. Replace BCM. Refer to 

BCS-70, "Removal and Installation"

.

2. Confirm the operation after replacement. 
Is the result normal?

YES

>> Inspection End.

NO

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

DLK-120

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

OFF POSITION WARNING DOES NOT OPERATE

OFF POSITION WARNING DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000009645257

1.

CHECK DTC WITH BCM

Check that DTC is not detected with BCM
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Perform trouble diagnosis relevant to DTC indicated.

2.

CHECK DTC WITH COMBINATION METER

Check that DTC is not detected with combination meter
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Perform trouble diagnosis relevant to DTC indicated.

3.

CHECK DOOR SWITCH

Check front door switch (driver side).

Refer to 

DLK-95, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the malfunctioning parts.

4.

CHECK COMBINATION METER BUZZER

Check combination meter buzzer.

Refer to 

DLK-77, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace the malfunctioning parts.

5.

CHECK INTELLIGENT KEY WARNING BUZZER

Check Intelligent Key warning buzzer.

Refer to 

DLK-77, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace the malfunctioning parts.

6.

REPLACE BCM

1. Replace BCM. Refer to 

BCS-70, "Removal and Installation"

.

2. Confirm the operation after replacement.
Is the result normal?

YES

>> Inspection End.

NO

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.