Nissan Versa Note. Manual - part 71

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-21

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

ACTIVE TEST

Monitor Item [Unit]

Main

Description

REQ SW -DR [On/Off]

×

Indicates condition of door request switch LH.

REQ SW -AS [On/Off]

×

Indicates condition of door request switch RH.

REQ SW -BD/TR [On/Off]

×

Indicates condition of back door request switch.

PUSH SW [On/Off]

Indicates condition of push-button ignition switch.

CLUTCH SW [On/Off]

×

Indicates condition of clutch interlock switch.

BRAKE SW 1 [On/Off]

×

Indicates condition of brake switch.

BRAKE SW 2 [On/Off]

Indicates condition of brake switch.

DETE/CANCL SW [On/Off]

×

Indicates condition of P (park) position.

SFT PN/N SW [On/Off]

×

Indicates condition of P (park) or N (neutral) position.

UNLK SEN -DR [On/Off]

×

Indicates condition of door unlock sensor.

PUSH SW -IPDM [On/Off]

Indicates condition of push-button ignition switch received from IPDM E/R on 
CAN communication line.

IGN RLY1 -F/B [On/Off]

Indicates condition of ignition relay 1 received from IPDM E/R on CAN commu-
nication line.

DETE SW -IPDM [On/Off]

Indicates condition of detent switch received from TCM on CAN communication 
line.

SFT PN -IPDM [On/Off]

Indicates condition of P (park) or N (neutral) position from TCM on CAN com-
munication line.

SFT P -MET [On/Off]

Indicates condition of P (park) position from TCM on CAN communication line.

SFT N -MET [On/Off]

Indicates condition of N (neutral) position from IPDM E/R on CAN communica-
tion line.

ENGINE STATE [Stop/Start/Crank/Run]

×

Indicates condition of engine state from ECM on CAN communication line.

VEH SPEED 1 [mph/km/h]

×

Indicates condition of vehicle speed signal received from ABS on CAN commu-
nication line.

VEH SPEED 2 [mph/km/h]

×

Indicates condition of vehicle speed signal received from combination meter on 
CAN communication line.

DOOR STAT -DR [LOCK/READY/UNLK]

×

Indicates condition of driver side door status.

DOOR STAT -AS [LOCK/READY/UNLK]

×

Indicates condition of passenger side door status.

ID OK FLAG [Set/Reset]

Indicates condition of Intelligent Key ID.

PRMT ENG STRT [Set/Reset]

Indicates condition of engine start possibility.

RKE OPE COUN1 [0-19]

×

When remote keyless entry receiver receives the signal transmitted while oper-
ating on Intelligent Key, the numerical value start changing.

RKE OPE COUN2 [0-19]

×

When remote keyless entry receiver receives the signal transmitted while oper-
ating on Intelligent Key, the numerical value start changing.

RKE-LOCK [On/Off]

Indicates condition of lock signal from Intelligent Key.

RKE-UNLOCK [On/Off]

Indicates condition of unlock signal from Intelligent Key.

RKE-PANIC [On/Off]

Indicates condition of panic signal from Intelligent Key.

RKE-MODE CHG [On/Off]

Indicates condition of mode change signal from Intelligent Key.

Test Item

Description

INSIDE BUZZER

This test is able to check combination meter warning chime operation [Take Out/Knob/Key/
Off].

LCD

This test is able to check combination meter display information [Off/LK WN/OUTKEY/NO 
KY/BATT/INSRT/SFT P/ROTAT/ID NG/B&P I/B&P N].

BATTERY SAVER

This test is able to check battery saver operation [On/Off].

ENGINE SW ILLUMI

This test is able to check push-button ignition switch START indicator operation [On/Off].

BCS-22

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

WORK SUPPORT

PUSH SWITCH INDICATOR

This test is able to check push-button ignition switch indicator operation [On/Off].

INT LAMP

This test is able to check interior room lamp operation [On/Off].

INDICATOR

This test is able to check combination meter warning lamp operation [KEY ON/KEY IND/Off].

FLASHER

This test is able to check hazard lamp operation [LH/RH/Off].

OUTSIDE BUZZER

This test is able to check Intelligent Key warning buzzer operation [On/Off].

HORN

This test is able to check horn operation [On].

P RANGE

This test is able to check CVT shift selector illumination operation [On/Off].

Test Item

Description

Support Item

Setting

Description

LOCK/UNLOCK BY I-KEY

On*

Door lock/unlock function from Intelligent Key ON. 

Off

Door lock/unlock function from Intelligent Key OFF. 

ANTI KEY LOCK IN FUNCTI

On*

Anti lock out setting ON.

Off

Anti lock out setting OFF.

ANS BACK I-KEY UNLOCK

Off

No buzzer reminder when doors are unlocked with request switch.

On*

Buzzer reminder when doors are unlocked with request switch.

ANS BACK I-KEY LOCK

Horn Chirp

Horn chirp reminder when doors are locked with request switch.

Buzzer*

Buzzer reminder when doors are locked with request switch.

Off

No reminder when doors are locked with request switch.

HORN WITH KEYLESS LOCK

Off

Horn chirp reminder when doors are locked with Intelligent Key.

On*

No horn chirp reminder when doors are locked with Intelligent Key.

HAZARD ANSWER BACK

Lock/Unlock*

Hazard warning lamp activation when doors are locked/unlocked 
with Intelligent Key or request switch.

Unlock Only

Hazard warning lamp activation when doors are unlocked with Intel-
ligent Key or request switch.

Lock Only

Hazard warning lamp activation when doors are locked with Intelli-
gent Key or request switch.

Off

No hazard warning lamp activation when doors are locked/unlocked 
with Intelligent Key or request switch.

INSIDE ANT DIAGNOSIS

—

This function allows inside key antenna self-diagnosis.

CONFIRM KEY FOB ID

—

Intelligent Key ID code can be checked.

SHORT CRANKING OUTPUT

Start

70 msec

Starter motor operation duration time setting.

100 msec

200 msec

End

—

PANIC ALARM SET

MODE 3

1.5 sec

Intelligent Key panic alarm button setting.

MODE 2

OFF

MODE 1*

0.5 sec

LO- BATT OF KEY FOB WARN

On*

Intelligent Key low battery warning ON. 

Off

Intelligent Key low battery warning OFF. 

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-23

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

*: Initial Setting

COMB SW
COMB SW : CONSULT Function (BCM - COMB SW)

INFOID:0000000009693573

DATA MONITOR

BCM
BCM : CONSULT Function (BCM - BCM)

INFOID:0000000009693574

ECU IDENTIFICATION

The BCM part number is displayed.

SELF DIAGNOSTIC RESULT

Refer to 

BCS-48, "DTC Index"

.

WORK SUPPORT

CONFIGURATION

Refer to 

BCS-58, "Description"

.

AUTO LOCK SET

MODE7

5 min

Auto door lock time setting.

MODE6

4 min

MODE5

3 min

MODE4

2 min

MODE3*

1 min

MODE2

30 sec

MODE1

Off

Support Item

Setting

Description

Monitor Item [Unit]

Description

FR WIPER HI [On/Off]

Indicates condition of wiper operation of combination switch.

FR WIPER LOW [On/Off]

FR WASHER SW [On/Off]

FR WIPER INT [On/Off]

INT VOLUME [1 - 7]

Indicates condition of intermittent wiper operation of combination switch.

RR WIPER ON [On/Off]

Indicates condition of rear wiper operation of combination switch.

RR WIPER INT [On/Off]

RR WASHER SW [On/Off]

TURN SIGNAL R [On/Off]

Indicates condition of right turn signal operation of combination switch.

TURN SIGNAL L [On/Off]

Indicates condition of left turn signal operation of combination switch.

TAIL LAMP SW [On/Off]

Indicates condition of tail lamp switch operation of combination switch.

HI BEAM SW [On/Off]

Indicates condition of Hi beam switch operation of combination switch.

HEAD LAMP SW 1 [On/Off]

Indicates condition of head lamp switch 1 operation of combination switch.

HEAD LAMP SW 2 [On/Off]

Indicates condition of head lamp switch 2 operation of combination switch.

PASSING SW [On/Off]

Indicates condition of passing switch operation of combination switch.

FR FOG SW [On/Off]

Indicates condition of front fog lamp switch operation of combination switch.

Support Item

Setting

Description

RESET SETTING VALUE

Reset

Returns BCM to initial value in factory shipment.

Cancel

Cancels the reset function.

BCS-24

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

CAN DIAG SUPPORT MNTR

Refer to 

LAN-12, "CAN Diagnostic Support Monitor"

.

IMMU
IMMU : CONSULT Function (BCM - IMMU)

INFOID:0000000009693575

SELF DIAGNOSTIC RESULT

Refer to 

BCS-48, "DTC Index"

.

DATA MONITOR

ACTIVE TEST

WORK SUPPORT

BATTERY SAVER
BATTERY SAVER : CONSULT Function (BCM - BATTERY SAVER)

INFOID:0000000009693576

DATA MONITOR

Monitor Item [Unit]

Description

CONFRM ID ALL [Yet/DONE]

Switches to DONE when an Intelligent Key is registered.

CONFIRM ID4 [Yet/DONE]

CONFIRM ID3 [Yet/DONE]

CONFIRM ID2 [Yet/DONE]

CONFIRM ID1 [Yet/DONE]

TP 4 [Yet/DONE]

DONE indicates the number of Intelligent Key ID which has been registered.

TP 3 [Yet/DONE]

TP 2 [Yet/DONE]

TP 1 [Yet/DONE]

PUSH SW [On/Off]

Indicates condition of push-button ignition switch.

Test Item

Description

THEFT IND

This test is able to check security indicator operation [On/Off]. 

Support Item

Setting

Description

CONFIRM DONGLE ID

—

Dongle ID code can be read.

Monitor Item [Unit]

Description

REQ SW -DR [On/Off]

Indicates condition of door request switch LH.

REQ SW -AS [On/Off]

Indicates condition of door request switch RH.

PUSH SW [On/Off]

Indicates condition push-button ignition switch.

UNLK SEN -DR [On/Off]

Indicates condition of door unlock sensor.

DOOR SW-DR [On/Off]

Indicates condition of front door switch LH.

DOOR SW-AS [On/Off]

Indicates condition of front door switch RH.

DOOR SW-RR [On/Off]

Indicates condition of rear door switch RH.

DOOR SW-RL [On/Off]

Indicates condition of rear door switch LH.

DOOR SW-BK [On/Off]

Indicates condition of back door switch.

CDL LOCK SW [On/Off]

Indicates condition of lock signal from door lock and unlock switch.

CDL UNLOCK SW [On/Off]

Indicates condition of unlock signal from door lock and unlock switch.

KEY CYL LK-SW [On/Off]

Indicates condition of lock signal from door key cylinder switch.