Nissan Teana J32. Manual - part 1026

SEC-92

< COMPONENT DIAGNOSIS >

[INTELLIGENT KEY SYSTEM]

B261A PUSH-BUTTON IGNITION SWITCH

B261A PUSH-BUTTON IGNITION SWITCH

Description

INFOID:0000000003815032

BCM transmits the change in the power supply position with the push-button ignition switch to IPDM E/R via
CAN communication. IPDM E/R transmits the power supply position status via CAN communication to BCM.

DTC Logic

INFOID:0000000003815033

DTC DETECTION LOGIC

NOTE:
• If DTC B261A is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

SEC-28, "BCM : DTC Logic"

.

• If DTC B261A is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

SEC-30, "BCM : DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE 1

1.

Press push-button ignition switch for 1 second under the following condition.

-

Selector lever is in the P or N position.

-

Do not depress brake pedal.

2.

Check “Self diagnostic result” with CONSULT-III.

Is DTC detected?

YES

>> Go to 

SEC-92, "Diagnosis Procedure"

NO

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE 2

1.

Insert Intelligent Key into the key slot.

2.

Press the push-button ignition switch under the following conditions and wait for at least 1 second.

-

Selector lever is in the P or N position.

-

Do not depress brake pedal.

3.

Check “Self diagnostic result” with CONSULT-III.

Is DTC detected?

YES

>> Go to 

SEC-92, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000003815034

1.

INSPECTION START

Check the case in which DTC is detected.
• Case1: It is detected when push-button ignition switch is pressed for 1 second
• Case2: It is detected after Intelligent Key is inserted into key slot and push-button ignition switch is pressed
In which case is DTC detected?

Case1 >> GO TO 2.
Case2 >> GO TO 4.

2.

CHECK PUSH-BUTTON IGNITION SWITCH OUTPUT SIGNAL 1

1.

Turn ignition switch OFF.

DTC No.

Trouble diagnosis 

name

DTC detecting condition

Possible cause

B261A

PUSH-BUTTON 
IGNITION 
SWITCH

BCM detects the difference between the following for 
1 second or more
• Power supply position with push-button ignition 

switch

• Power supply position from IPDM E/R (CAN)

• Harness or connectors

(Push-button ignition switch circuit is 
open or shorted)

• Between BCM and push-button igni-

tion switch

• Between IPDM E/R and push-button 

ignition switch

B261A PUSH-BUTTON IGNITION SWITCH

SEC-93

< COMPONENT DIAGNOSIS >

[INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

2.

Disconnect push-button ignition switch connector and IPDM E/R connector.

3.

Check voltage between push-button ignition switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> GO TO 3.

3.

CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT 1

1.

Disconnect BCM connector.

2.

Check continuity between push-button ignition switch harness connector and BCM harness connector.

3.

Check continuity between push-button ignition switch harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-78, "Removal and Installation"

.

NO

>> Repair or replace harness.

4.

CHECK PUSH-BUTTON IGNITION SWITCH OUTPUT SIGNAL 2

1.

Turn ignition switch OFF.

2.

Disconnect push-button ignition switch connector and BCM connector.

3.

Check voltage between push-button ignition switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> GO TO 5.

5.

CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT 2

1.

Disconnect IPDM E/R connector.

2.

Check continuity between push-button ignition switch harness connector and IPDM E/R harness connec-
tor.

3.

Check continuity between push-button ignition switch harness connector and ground.

(+)

(–)

Voltage (V)

(Approx.)

Push-button ignition switch

Connector

Terminal

M101

4

Ground

Battery voltage

Push-button ignition switch

BCM

Continuity

Connector

Terminal

Connector

Terminal

M101

4

M122

89

Existed

Push-button ignition switch

Ground

Continuity

Connector

Terminal

M101

4

Not existed

(+)

(–)

Voltage (V)

(Approx.)

Push-button ignition switch

Connector

Terminal

M101

4

Ground

Battery voltage

Push-button ignition switch

IPDM E/R

Continuity

Connector

Terminal

Connector

Terminal

M101

4

E10

28

Existed

Push-button ignition switch

Ground

Continuity

Connector

Terminal

M101

4

Not existed

SEC-94

< COMPONENT DIAGNOSIS >

[INTELLIGENT KEY SYSTEM]

B261A PUSH-BUTTON IGNITION SWITCH

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-34, "Removal and Installation"

.

NO

>> Repair or replace harness.

6.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-35, "Intermittent Incident"

.

>> INSPECTION END

B261E VEHICLE TYPE

SEC-95

< COMPONENT DIAGNOSIS >

[INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B261E  VEHICLE TYPE

Description

INFOID:0000000003815035

There are two types of vehicles.
• HEV
• Conventional

DTC Logic

INFOID:0000000003815036

DTC DETECTION LOGIC

NOTE:
• If DTC B261E is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

SEC-28, "BCM : DTC Logic"

.

• If DTC B261E is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

SEC-30, "BCM : DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON.

2.

Check “Self diagnostic result” with CONSULT-III.

Is DTC detected?

YES

>> Go to 

SEC-95, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000003815037

1.

INSPECTION START

1.

Turn ignition switch ON.

2.

Check “Self diagnostic result” with CONSULT-III.

3.

Touch “ERASE”.

4.

Perform DTC Confirmation Procedure.
See 

SEC-95, "DTC Logic"

.

Is the 1st trip DTC B261E displayed again?

YES

>> Replace BCM. Refer to 

BCS-78, "Removal and Installation"

.

NO

>> INSPECTION END

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B261E

VEHICLE TYPE

Difference of BCM configuration

BCM