Nissan Murano Z51. Manual - part 1523

WT-30

< DTC/CIRCUIT DIAGNOSIS >

C1716, C1717, C1718, C1719 TRANSMITTER

C1716, C1717, C1718, C1719 TRANSMITTER

DTC Logic

INFOID:0000000005575990

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

DTC REPRODUCTION PROCEDURE

With CONSULT-III

1.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

2.

Check the tire pressure for all wheels and adjust to the specified value. Refer to 

WT-60, "Tire Air Pres-

sure"

. 

3.

Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.

Is DTC “C1716”, “C1717”, “C1718”, “C1719” detected?

YES

>> Perform trouble diagnosis. Refer to 

WT-30, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000005575991

1.

CHECK TIRE PRESSURE

Check the internal pressure of all wheels. Refer to 

WT-60, "Tire Air Pressure"

. 

Is the inspection result normal?

YES

>> Replace the DTC-detected malfunctioning transmitter. Refer to 

WT-57, "Exploded View"

.

NO

>> After adjusting the tire pressure, GO TO 2.

2.

CHECK TIRE PRESSURE SIGNAL

With CONSULT-III

1.

Check and adjust the tire pressure for all wheels. Refer to 

WT-60, "Tire Air Pressure"

. 

2.

Perform transmitter ID registration for all wheels. Refer to 

WT-22, "ID REGISTRATION PROCEDURE :

Special Repair Requirement"

. 

3.

Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.

4.

Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.

5.

Select “BCM” in “DATA MONITOR”, and check that the tire pressures match the standard value.

CAUTION:

Stop the vehicle and within 15 minutes, use CONSULT-III “DATA MONITOR” to display the tire
pressure for all wheels.

6.

Check that “DATA MONITOR” displays tire pressure of 438.60 kPa (4.47 kg/cm

2

, 63.60 Psi).

Is the inspection 438.60 kPa (4.47 kg/cm

2

, 63.60 Psi)?

YES

>> Replace transmitter the tire pressure 438.60 kPa (4.386 bar, 4.47 kg/cm

2

, 63.60 Psi) displayed.

Refer to 

WT-57, "Exploded View"

.

NO

>> GO TO 1.

DTC

Display item

Malfunction detected condition

Possible case

C1716

[PRESSDATA ERR] FL

Malfunction in the tire pressure data from the front left 
wheel transmitter.

• ID registration is not fin-

ished

• Transmitter malfunction

C1717

[PRESSDATA ERR] FR

Malfunction in the tire pressure data from the front right 
wheel transmitter.

C1718

[PRESSDATA ERR] RR

Malfunction in the tire pressure data from the rear right 
wheel transmitter.

C1719

[PRESSDATA ERR] RL

Malfunction in the tire pressure data from the rear left 
wheel transmitter.

C1716, C1717, C1718, C1719 TRANSMITTER

WT-31

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

Special Repair Requirement

INFOID:0000000005575992

1.

CHECK TIRE PRESSURE

Check all tires for tire pressures. Refer to 

WT-60, "Tire Air Pressure"

.

Does all tire pressure data meet the specification?

YES

>> GO TO 2.

NO

>> Inspect or repair the tires or wheels and adjust the tire pressure to the specification.

2.

PERFORM ID REGISTRATION

Perform ID registration. Refer to 

WT-22, "ID REGISTRATION PROCEDURE : Special Repair Requirement"

.

>> END

WT-32

< DTC/CIRCUIT DIAGNOSIS >

C1729 VEHICLE SPEED SIGNAL

C1729 VEHICLE SPEED SIGNAL

Description

INFOID:0000000005575993

BCM detects no vehicle speed signal.

DTC Logic

INFOID:0000000005575994

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

DTC REPRODUCTION PROCEDURE

With CONSULT-III

1.

Drive for several minutes at a speed of 40 km/h (25 MPH) or more, then stop the vehicle.

2.

Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.

Is DTC “C1729” detected?

YES

>> Perform trouble diagnosis. Refer to 

WT-32, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000005575995

1.

PERFORM UNIFIED METER AND A/C AMP. SELF-DIAGNOSIS

With CONSULT-III

Perform “SELF-DIAG RESULTS” of “METER/M&A”.

Is any DTC detected?

YES

>> Check the DTC. Refer to 

MWI-76, "DTC Index"

.

NO

>> GO TO 2.

2.

PERFORM SELF-DIAGNOSIS

With CONSULT-III

Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.

Is DTC “C1729” detected?

YES

>> Replace BCM. Refer to 

WT-11, "COMMON ITEM : CONSULT-III Function (BCM - COMMON

ITEM)"

.

NO

>> GO TO 3.

3.

CHECK INFORMATION

With CONSULT-III

1.

Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.

2.

Select “BCM” in “DATA MONITOR”, and check the input/output values. Refer to 

BCS-47, "Reference

Value"

. 

Is the inspection result normal?

YES

>> Check pin terminal and connection of each harness connector for malfunctioning conditions. 

NO

>> Replace BCM. Refer to 

BCS-95, "Exploded View"

. 

Special Repair Requirement

INFOID:0000000005575996

1.

CHECK TIRE PRESSURE

Check all tires for tire pressures. Refer to 

WT-60, "Tire Air Pressure"

.

Does all tire pressure data meet the specification?

DTC 

number

Trouble diagnosis name

DTC detecting condition

Possible case

C1729

VHCL SPEED SIG ERR

Vehicle speed signal not detected.

• CAN communication error
• Unified meter and A/C amp. mal-

function

C1729 VEHICLE SPEED SIGNAL

WT-33

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

YES

>> GO TO 2.

NO

>> Inspect or repair the tires or wheels and adjust the tire pressure to the specification.

2.

PERFORM ID REGISTRATION

Perform ID registration. Refer to 

WT-22, "ID REGISTRATION PROCEDURE : Special Repair Requirement"

.

>> END