Nissan Murano Z51. Manual - part 1439

SHIFT LOCK SYSTEM

TM-107

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F09B]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

5.

CHECK HARNESS BETWEEN STOP LAMP SWITCH AND CVT SHIFT SELECTOR (PART 1)

1.

Disconnect CVT shift selector connector.

2.

Check continuity between stop lamp switch vehicle side harness connector terminal and CVT shift selec-
tor vehicle side harness connector terminal.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace damaged parts.

6.

CHECK HARNESS BETWEEN STOP LAMP SWITCH AND CVT SHIFT SELECTOR (PART 2)

Check continuity between control vehicle side harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace damaged parts.

7.

CHECK GROUND CIRCUIT

Check continuity between CVT shift selector vehicle side harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> Repair or replace damaged parts.

8.

CHECK CVT SHIFT SELECTOR

1.

Shift selector lever to “P” position.

2.

Check continuity between CVT shift selector connector terminals.

Is the inspection result normal?

YES

>> GO TO 9.

NO

>> Replace CVT shift selector. Refer to 

TM-162, "Exploded View"

.

9.

CHECK SHIFT LOCK SOLENOID

1.

Remove shift lock unit. Refer to 

TM-162, "Exploded View"

.

2.

Check shift lock solenoid. Refer to 

TM-108, "Component Inspection (Shift Lock Solenoid)"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair or replace damaged parts.

Stop lamp switch vehicle side harness connector

CVT shift selector vehicle side harness connec-

tor

Continuity

Connector

Terminal

Connector

Terminal

E116

4

M57

6

Existed

CVT shift selector vehicle side harness connector

Ground

Continuity

Connector

Terminal

M57

6

Not existed

CVT shift selector vehicle side harness connector

Ground

Continuity

Connector

Terminal

M57

7

Existed

CVT shift selector connector

Continuity

Connector

Terminal

M57

6

7

Existed

TM-108

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F09B]

SHIFT LOCK SYSTEM

Component Inspection (Stop Lamp Switch)

INFOID:0000000005514070

1.

CHECK STOP LAMP SWITCH

Check continuity between stop lamp switch connector terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace stop lamp switch. Refer to 

BR-20, "Exploded View"

.

Component Inspection (Shift Lock relay)

INFOID:0000000005514071

1.

CHECK SHIFT LOCK RELAY

Apply voltage to terminals of shift lock relay connector to check the continuity.

CAUTION:

Connect the fuse between the terminals when applying the voltage.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace shift lock relay.

Component Inspection (Shift Lock Solenoid)

INFOID:0000000005514072

1.

CHECK SHIFT LOCK SOLENOID

Apply voltage to CVT shift selector connector terminals and then check that shift lock solenoid is activated.

CAUTION:

Connect the fuse between the terminals when applying the voltage.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace shift lock unit. Refer to 

TM-162, "Exploded View"

.

Stop lamp switch connector

Condition

Continuity

Connector

Terminal

E116

3

4

Depressed brake pedal

Existed

Released brake pedal

Not existed

Shift lock relay connector

Condition

Continuity

Connector

Terminal

E53

5

3

Apply 12 V direct voltage between terminals 2 and 1.

Existed

(+) (fuse)

(

−

)

Condition

Status

CVT shift selector connector

Connector

Terminal

M57

6

7

• Park switch: ON
• Apply 12 V direct current be-

tween terminals 6 and 7.

Shift lock solenoid operates

OVERDRIVE CONTROL SWITCH

TM-109

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F09B]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

OVERDRIVE CONTROL SWITCH

Description

INFOID:0000000005514073

• The Overdrive control switch is installed to the selector lever knob.
• When pushing the Overdrive control switch (OD OFF indicator lamp turns ON), the driving condition

becomes Overdrive OFF. When pushing again the Overdrive control switch (OD OFF indicator lamp turns
OFF), the driving condition changes to D range.

Component Function Check

INFOID:0000000005514074

1.

CHECK OVERDRIVE CONTROL SWITCH SIGNAL

1.

Turn ignition switch ON.

2.

Select “Data Monitor” in “TRANSMISSION”.

3.

Check the ON/OFF operations of monitor item.

Is the inspection result normal?

YES

>> INSPECTION END.

NO

>> Go to 

TM-109, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000005514075

1.

 CHECK CAN COMMUNICATION CIRCUIT

Perform “Self Diagnostic Results” in “TRANSMISSION”.

Is “U1000” indicated?

YES

>> Check CAN communication line. Refer to 

TM-40, "Description"

.

NO

>> GO TO 2.

2.

CHECK COMBINATION METER

Perform “Self Diagnostic Results” in “METER/M&A”.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Check DTC detected item. Refer to 

MWI-76, "DTC Index"

.

3.

CHECK OVERDRIVE CONTROL SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect CVT shift selector connector.

3.

Check continuity overdrive control switch.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace damaged parts.

4.

CHECK GROUND CIRCUIT (PART 1)

Check continuity between CVT shift selector vehicle side harness connector terminal and ground.

Monitor item

Condition

Status

SPORT MODE SW

While pushing overdrive control switch

On

Other conditions

Off

CVT shift selector connector

Condition

Continuity

Connector

Terminal

M57

1

4

While pushing overdrive control switch

Existed

Other condition

Not existed

TM-110

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F09B]

OVERDRIVE CONTROL SWITCH

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace damaged parts.

5.

CHECK HARNESS BETWEEN CVT SHIFT SELECTOR AND COMBINATION METER (PART 1)

1.

Disconnect combination meter connector.

2.

Check continuity between CVT shift selector vehicle side harness connector terminal and combination
meter vehicle side harness connector terminal.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace damaged parts.

6.

CHECK HARNESS BETWEEN CVT SHIFT SELECTOR AND COMBINATION METER (STEP 2)

Check continuity between CVT shift selector vehicle side harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace damaged parts.

7.

DETECT MALFUNCTIONING ITEMS

Check TCM connector pin terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES

>> Replace TCM. Refer to 

TM-160, "Exploded View"

.

NO

>> Repair or replace damaged parts.

CVT shift selector vehicle side harness connector

Ground

Continuity

Connector

Terminal

M57

4

Existed

CVT shift selector vehicle side harness connector

Combination meter vehicle side harness connector

Continuity

Connector

Terminal

Connector

Terminal

M57

1

M34

32

Existed

CVT shift selector vehicle side harness connector

Ground

Continuity

Connector

Terminal

M57

1

Not existed