Nissan Murano Z51. Manual - part 1356

SRC-194

< DTC/CIRCUIT DIAGNOSIS >

[FOR MEXICO]

B1011, B1012, B1013, B1014, B1015 DIAGNOSIS SENSOR UNIT

B1011, B1012, B1013, B1014, B1015 DIAGNOSIS SENSOR UNIT

Description

INFOID:0000000005513712

DTC B1011, B1012, B1013, B1014, B1015 DIAGNOSIS SENSOR UNIT

Detects the whole SRS electrical system and displays the malfunction either by illuminating or blinking the air
bag warning lamp in the combination meter. Malfunctioning part can be detected by on board self-diagnosis
system and electro-diagnosis tester CONSULT-III.

OPERATION

It detects a shock that exceeds specified level and monitors such systems as the driver and passenger air
bag, front side air bag, side curtain air bag, pre-tensioner seat belts operate properly. 

STRUCTURE

It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.

INSTALLATION

Air bag diagnosis sensor unit is installed under the center console with fixed bolts.

DTC Logic

INFOID:0000000005513713

DTC DETECTION LOGIC

With CONSULT-III

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (With CONSULT-III)

1.

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

2.

CHECK SELF-DIAG RESULT

Check the screen of CONSULT-III.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-195, "Diagnosis Procedure"

.

NO

>> INSPECTION END.

DTC CONFIRMATION PROCEDURE (Without CONSULT-III)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

1.

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1011

B1012
B1013
B1014
B1015

CONTROL UNIT 

Air bag diagnosis sensor unit is out of 
order or mis-match

• Internal breakdown in air bag diag-

nosis sensor unit

• Mis-match between specification on 

vehicle and configuration in air bag 
diagnosis sensor unit

B1011, B1012, B1013, B1014, B1015 DIAGNOSIS SENSOR UNIT

SRC-195

< DTC/CIRCUIT DIAGNOSIS >

[FOR MEXICO]

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

2.

CHECK AIR BAG WARNING LAMP

Check the warning lamp status.
Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart.

SRC-314

.

NO

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000005513714

With CONSULT-III

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device. 

DIAGNOSTIC PROCEDURE

1.

CHECK HARNESS CONNECTOR

Check the connection of harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace harness connectors.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace wiring harness.

3.

CHECK AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit.

2.

Check the screen of CONSULT-III.

Is the inspection result normal?

YES

>> INSPECTION END.

NO

>> Check the intermittent incident. Refer to 

GI-39, "Intermittent Incident"

.

SRC-196

< DTC/CIRCUIT DIAGNOSIS >

[FOR MEXICO]

B1026, B1027, B1028, B1029, B1030, B1031 DIAGNOSIS SENSOR UNIT

B1026, B1027, B1028, B1029, B1030, B1031 DIAGNOSIS SENSOR UNIT

Description

INFOID:0000000005513715

DTC B1026, B1027, B1028, B1029, B1030, B1031 DIAGNOSIS SENSOR UNIT

Detects the whole SRS electrical system and displays the malfunction either by illuminating or blinking the air
bag warning lamp in the combination meter. Malfunctioning part can be detected by on board self-diagnosis
system and electro-diagnosis tester CONSULT-III.

OPERATION

It detects a shock that exceeds specified level and monitors such systems as the driver and passenger air
bag, front side air bag, side curtain air bag, pre-tensioner seat belts operate properly. 

STRUCTURE

It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.

INSTALLATION

Air bag diagnosis sensor unit is installed under the center console with fixed bolts.

DTC Logic

INFOID:0000000005513716

DTC DETECTION LOGIC

With CONSULT-III

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (With CONSULT-III)

1.

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

2.

CHECK SELF-DIAG RESULT

Check the screen of CONSULT-III.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-197, "Diagnosis Procedure"

.

NO

>> INSPECTION END.

DTC CONFIRMATION PROCEDURE (Without CONSULT-III)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

1.

INSPECTION START

Turn ignition switch ON.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1026
B1027
B1028
B1029
B1030
B1031

CONTROL UNIT 

Air bag diagnosis sensor unit is out of 
order or mis-match

• Internal breakdown in air bag diag-

nosis sensor unit

• Mis-match between specification on 

vehicle and configuration in air bag 
diagnosis sensor unit

B1026, B1027, B1028, B1029, B1030, B1031 DIAGNOSIS SENSOR UNIT

SRC-197

< DTC/CIRCUIT DIAGNOSIS >

[FOR MEXICO]

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

>> GO TO 2.

2.

CHECK AIR BAG WARNING LAMP

Check the warning lamp status.

Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart.

SRC-314

.

NO

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000005513717

With CONSULT-III

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device. 

DIAGNOSTIC PROCEDURE

1.

CHECK HARNESS CONNECTOR

Check the connection of harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace harness connectors.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

CHECK AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit.

2.

Check the screen of CONSULT-III.

Is the inspection result normal?

YES

>> INSPECTION END.

NO

>> Check the intermittent incident. Refer to 

GI-39, "Intermittent Incident"

.