Nissan Murano Z51. Manual - part 1169

RF-16

< DTC/CIRCUIT DIAGNOSIS >

SUNROOF SWITCH

YES

>> GO TO 3.

NO

>> Repair or the replace harness.

3.

CHECK SUNROOF SWITCH GROUND CIRCUIT

Check continuity between sunroof switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK SUNROOF SWITCH

Check sunroof switch.
Refer to 

RF-16, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace sunroof switch. Refer to 

RF-116, "Removal and Installation"

.

5.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-39, "Intermittent Incident"

.

>> INSPECTION END

Component Inspection

INFOID:0000000005516837

SUNROOF SWITCH

1.

CHECK SUNROOF SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect sunroof switch connector.

3.

Check continuity sunroof switch terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace sunroof switch. Refer to 

RF-116, "Removal and Installation"

.

Sunroof switch

Ground

Continuity 

 Connector

Terminal

R6

1

Existed

Terminals

Condition

Continuity

2 

1

Sunroof switch is operated 

OPEN (2nd) or CLOSE (2nd)

Existed

Other than above

Not existed

3 

Sunroof switch is operated 

OPEN (1st) or OPEN (2nd)

Existed

Other than above

Not existed

4

Sunroof switch is operated 

CLOSE (1st) or CLOSE (2nd)

Existed

Other than above

Not existed

5

Sunroof switch is operated 

PUSH

Existed

Other than above

Not existed

DOOR SWITCH

RF-17

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

RF

N

O

P

DOOR SWITCH

Description

INFOID:0000000005516838

Detects door open/close condition.

Component Function Check

INFOID:0000000005516839

1.

CHECK FUNCTION

Check door switches (“DOOR SW-DR”, “DOOR SW-AS”) in Data Monitor” mode with CONSULT-III.

Is the inspection result normal?

YES

>> Door switch is OK.

NO

>> Refer to 

RF-17, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000005516840

1.

CHECK DOOR SWITCH INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect malfunctioning door switch connector.

3.

Check signal between malfunctioning door switch harness connector and ground with oscilloscope.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK DOOR SWITCH CIRCUIT 

1.

Disconnect BCM connector.

2.

Check continuity between BCM harness connector and door switch harness connector.

Monitor item

Condition

Status

DOOR SW-DR

 Front door (driver side)

OPEN

ON

CLOSE

OFF

DOOR SW-AS

 Front door (passenger side)

OPEN

ON

CLOSE

OFF

(+)

(–)

Voltage (V)

(Approx.)

Door switch

Connector

Terminal

Driver side

B34

2

Ground

Passenger side

B220

2

JPMIA0011GB

JPMIA0011GB

RF-18

< DTC/CIRCUIT DIAGNOSIS >

DOOR SWITCH

3.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-95, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK DOOR SWITCH 

Refer to 

RF-18, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace malfunctioning door switch. Refer to 

DLK-360, "Removal and Installation"

.

4.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-39, "Intermittent Incident"

.

>> INSPECTION END 

Component Inspection

INFOID:0000000005516841

1.

CHECK DOOR SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect door switch connector.

3.

Check door switch terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace malfunction door switch. Refer to 

DLK-360, "Removal and Installation"

.

BCM

Door switch

Continuity 

Connector

Terminal

Connector

Terminal

M123 (Driver side)

150

B34 (Driver side)

2

Existed

M123 (Passenger side)

124

B220 (Passenger side)

BCM

Ground

Continuity 

Connector

Terminal

M123 (Driver side)

150

Not existed

M123 (Passenger side)

124

Terminal

Condition

Continuity

Door switch

Each door

2

Ground part of door 

switch

Door switch pressed

Not existed

Door switch released

Existed

BCM (BODY CONTROL MODULE)

RF-19

< ECU DIAGNOSIS INFORMATION >

C

D

E

F

G

H

I

J

L

M

A

B

RF

N

O

P

ECU DIAGNOSIS INFORMATION

BCM (BODY CONTROL MODULE)

Reference Value

INFOID:0000000005681518

VALUES ON THE DIAGNOSIS TOOL

CONSULT-III MONITOR ITEM

Monitor Item

Condition

Value/Status

FR WIPER HI

Other than front wiper switch HI

Off

Front wiper switch HI

On

FR WIPER LOW

Other than front wiper switch LO

Off

Front wiper switch LO

On

FR WASHER SW

Front washer switch OFF

Off

Front washer switch ON

On

FR WIPER INT

Other than front wiper switch INT/AUTO

Off

Front wiper switch INT/AUTO

On

FR WIPER STOP

Front wiper is not in STOP position

Off

Front wiper is in STOP position

On

INT VOLUME

Wiper intermittent dial is in a dial position 1 - 7

Wiper intermittent dial 

position

RR WIPER ON

Other than rear wiper switch ON

Off

Rear wiper switch ON

On

RR WIPER INT

Other than rear wiper switch INT

Off

Rear wiper switch INT

On

RR WASHER SW

Rear washer switch OFF

Off

Rear washer switch ON

On

RR WIPER STOP

Rear wiper is in STOP position

Off

Rear wiper is not in STOP position

On

TURN SIGNAL R

Other than turn signal switch RH

Off

Turn signal switch RH

On

TURN SIGNAL L

Other than turn signal switch LH

Off

Turn signal switch LH

On

TAIL LAMP SW

Other than lighting switch 1ST and 2ND

Off

Lighting switch 1ST or 2ND

On

HI BEAM SW

Other than lighting switch HI

Off

Lighting switch HI

On

HEAD LAMP SW 1

Other than lighting switch 2ND

Off

Lighting switch 2ND

On

HEAD LAMP SW 2

Other than lighting switch 2ND

Off

Lighting switch 2ND

On

PASSING SW

Other than lighting switch PASS

Off

Lighting switch PASS

On

AUTO LIGHT SW

Other than lighting switch AUTO

Off

Lighting switch AUTO

On

FR FOG SW

Front fog lamp switch OFF

Off

Front fog lamp switch ON

On