Nissan X-Trail 32. Manual - part 468

SPINDLE MOTOR

DLK-213

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 1]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

NO

>> Repair or replace harness.

DLK-214

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 1]

SUPER LOCK ACTUATOR

SUPER LOCK ACTUATOR

DRIVER SIDE

DRIVER SIDE : Component Function Check

INFOID:0000000010735190

1.

CHECK FUNCTION

1.

Select “DOOR LOCK” of “BCM” using CONSULT.

2.

Select “SUPER LOCK” in “ACTIVE TEST” mode.

3.

Touch “LOCK” or “UNLOCK” to check that it works normally.

Is the inspection result normal?

YES

>> Super lock actuator is OK.

NO

>> Refer to 

DLK-214, "DRIVER SIDE : Diagnosis Procedure"

.

DRIVER SIDE : Diagnosis Procedure

INFOID:0000000010735191

1.

CHECK SUPER LOCK ACTUATOR SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect front door lock assembly (driver side) connector.

3.

Check voltage between front door lock assembly (driver side) harness connector and ground.

Is the inspection result normal?

YES

>> Replace front door lock assembly (driver side).

NO

>> GO TO 2.

2.

CHECK SUPER LOCK ACTUATOR CIRCUIT

1.

Disconnect BCM and each door lock assembly.

2.

Check continuity between BCM harness connector and front door lock assembly (driver side) harness
connector. 

3.

Check continuity between BCM connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK BCM OUTPUT SIGNAL

1.

Connect BCM connector.

2.

Check voltage between BCM harness connector and ground.

(+)

(–)

Condition

Voltage

Front door lock assembly (driver side)

Connector

Terminal

D35

5

Ground

Super lock

Release

9 – 16 V

6

Set

BCM

Front door lock assembly (driver side)

Continuity 

Connector

Terminal

Connector

Terminal

M85

148

D35

5

Existed

149

6

BCM

Ground

Continuity 

Connector

Terminal

M85

148

Not existed

149

SUPER LOCK ACTUATOR

DLK-215

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 1]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

Is the inspection result normal?

YES

>> Check for internal short of each door lock actuator.

NO

>> Replace BCM. Refer to 

BCS-121, "Removal and Installation"

.

PASSENGER SIDE

PASSENGER SIDE : Component Function Check

INFOID:0000000010735192

1.

CHECK FUNCTION

1.

Select “DOOR LOCK” of “BCM” using CONSULT.

2.

Select “SUPER LOCK” in “ACTIVE TEST” mode.

3.

Touch “LOCK” or “UNLOCK” to check that it works normally.

Is the inspection result normal?

YES

>> Super lock actuator is OK.

NO

>> Refer to 

DLK-215, "PASSENGER SIDE : Diagnosis Procedure"

.

PASSENGER SIDE : Diagnosis Procedure

INFOID:0000000010735193

1.

CHECK SUPER LOCK ACTUATOR SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect front door lock assembly (passenger side) connector.

3.

Check voltage between front door lock assembly (passenger side) harness connector and ground.

Is the inspection result normal?

YES

>> Replace front door lock assembly (passenger side).

NO

>> GO TO 2.

2.

CHECK SUPER LOCK ACTUATOR CIRCUIT

1.

Disconnect BCM and each door lock assembly.

2.

Check continuity between BCM harness connector and front door lock assembly (passenger side) har-
ness connector. 

3.

Check continuity between BCM connector and ground.

(+)

(–)

Condition

Voltage

BCM

Connector

Terminal

M85

148

Ground

Super lock

Release

9 – 16 V

149

Set

(+)

(–)

Condition

Voltage

Front door lock assembly (passenger side)

Connector

Terminal

D73

1

Ground

Super lock

Set

9 – 16 V

2

Release

BCM 

Front door lock assembly (passenger side)

Continuity 

Connector

Terminal

Connector

Terminal

M85

139

D73

2

Existed

149

1

BCM

Ground

Continuity 

Connector

Terminal

M85

139

Not existed

149

DLK-216

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 1]

SUPER LOCK ACTUATOR

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK BCM OUTPUT SIGNAL

1.

Connect BCM connector.

2.

Check voltage between BCM harness connector and ground.

Is the inspection result normal?

YES

>> Check for internal short of each door lock actuator.

NO

>> Replace BCM. Refer to 

BCS-121, "Removal and Installation"

.

REAR LH

REAR LH : Component Function Check

INFOID:0000000010735194

1.

CHECK FUNCTION

1.

Select “DOOR LOCK” of “BCM” using CONSULT.

2.

Select “SUPER LOCK” in “ACTIVE TEST” mode.

3.

Touch “LOCK” or “UNLOCK” to check that it works normally.

Is the inspection result normal?

YES

>> Super lock actuator is OK.

NO

>> Refer to 

DLK-216, "REAR LH : Diagnosis Procedure"

.

REAR LH : Diagnosis Procedure

INFOID:0000000010735195

1.

CHECK SUPER LOCK ACTUATOR OUTPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect rear door lock assembly LH.

3.

Check voltage between rear door lock assembly LH harness connector and ground.

Is the inspection result normal?

YES

>> Replace rear door lock assembly LH.

NO

>> GO TO 2.

2.

CHECK SUPER LOCK ACTUATOR CIRCUIT

1.

Disconnect BCM, each door lock actuator and fuel filler lid lock actuator connector. 

2.

Check continuity between BCM harness connector and rear door lock assembly LH harness connector. 

3.

Check continuity between BCM harness connector and ground.

(+)

(–)

Condition

Voltage

BCM

Connector

Terminal

M85

139

Ground

Super lock

Release

9 – 16 V

149

Set

(+)

(–)

Condition

Voltage

Rear door lock assembly LH

Connector

Terminal

D118

1

Ground

Super lock

Set

9 – 16 V

2

Release

BCM

Rear door lock assembly LH

Continuity 

Connector

Terminal

Connector

Terminal

B46

124

D118

2

Existed

131

1