Nissan Qashqai J11. Manual - part 427

ECK-268

< DTC/CIRCUIT DIAGNOSIS >

[K9K]

P0606 ECM

P0606 ECM

DTC Logic

INFOID:0000000010289869

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DIAGNOSIS PROCEDURE

NOTE:
DTC P0606 can not duplicate.

>> Proceed to 

ECK-268, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000010289870

1.

INSPECTION START

1.

Turn ignition switch ON.

2.

Erase DTC.

3.

Turn ignition switch OFF and wait for 20 seconds.

4.

Turn ignition switch ON and perform the self-diagnosis.

Is the DTC P0606 displayed again?

YES

>> GO TO 2.

NO

>> INSPECTION END

2.

REPLACE ECM

Replace ECM. Refer to 

ECK-399, "Removal and Installation"

.

>> INSPECTION END

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

Possible cause

P0606

COMPUTER
(Control module processor)
• 1.DEF: SYSTEM INTERNAL 

FAILURE

Internal error.

ECM

P060A ECM

ECK-269

< DTC/CIRCUIT DIAGNOSIS >

[K9K]

C

D

E

F

G

H

I

J

K

L

M

A

ECK

N

P

O

P060A ECM

DTC Logic

INFOID:0000000010289873

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 1 minute before conducting the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON and wait at least 1 second.

2.

Check DTC.

Is DTC detected?

YES

>> Proceed to 

ECK-269, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000010289874

1.

INSPECTION START

1.

Turn ignition switch ON.

2.

Erase DTC.

3.

Turn ignition switch OFF and wait for 1 minute.

4.

Turn ignition switch ON and wait at least 1 second.

5.

Perform the self-diagnosis.

Is the DTC P060A displayed again?

YES

>> GO TO 2.

NO

>> INSPECTION END

2.

REPLACE ECM

1.

Replace ECM.

2.

Perform 

ECK-131, "Work Procedure"

.

>> INSPECTION END

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

Possible cause

P060A

COMPUTER
(Internal control module monitoring 
processor performance)
• 1.DEF: —
• 2.DEF: JAMMED ACCELERA-

TOR PEDAL DETECTED

• 3.DEF: IMPLAUSIBLE SIGNAL
• 4.DEF: JAMMED ACCELERA-

TOR PEDAL DETECTED

Internal monitoring processor error.

ECM

ECK-270

< DTC/CIRCUIT DIAGNOSIS >

[K9K]

P060B ECM

P060B ECM

DTC Logic

INFOID:0000000010289875

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 1 minute before conducting the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON and wait at least 1 second.

2.

Check DTC.

Is DTC detected?

YES

>> Proceed to 

ECK-270, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000010289876

1.

INSPECTION START

1.

Turn ignition switch ON.

2.

Erase DTC.

3.

Turn ignition switch OFF and wait for 20 seconds.

4.

Turn ignition switch ON and perform the self-diagnosis.

Is the DTC P060B displayed again?

YES

>> GO TO 2.

NO

>> INSPECTION END

2.

REPLACE ECM

1.

Replace ECM. Refer to 

ECK-399, "Removal and Installation"

.

2.

Go to 

ECK-131, "Work Procedure"

.

>> INSPECTION END

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

Possible cause

P060B

COMPUTER
(Internal control module A/D processing 
performance)
• 1.DEF: —

Internal A/D processor error.

• ECM

P061A ECM

ECK-271

< DTC/CIRCUIT DIAGNOSIS >

[K9K]

C

D

E

F

G

H

I

J

K

L

M

A

ECK

N

P

O

P061A ECM

DTC Logic

INFOID:0000000010289877

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM DIAGNOSIS PROCEDURE

NOTE:
DTC P061A can not duplicate.

>> Proceed to 

ECK-271, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000010289878

1.

INSPECTION START

1.

Turn ignition switch ON.

2.

Erase DTC.

3.

Turn ignition switch OFF and wait for 1 minute.

4.

Turn ignition switch ON and wait at least 1 second.

5.

Perform the self-diagnosis.

Is the DTC P061A displayed again?

YES

>> GO TO 2.

NO

>> INSPECTION END

2.

REPLACE ECM

1.

Replace ECM.

2.

Perform 

ECK-131, "Work Procedure"

.

>> INSPECTION END

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

Possible cause

P061A

COMP
(Internal control module torque 
performance)
• 1.DEF: SIGNAL INCOHER-

ENCE

• 2.DEF: —
• 3.DEF: —
• 4.DEF: FAULT ALERTED VIA 

THE CONTROL UNIT

• 5.DEF: —
• 6.DEF: —

ECM detects internal error.

ECM