Nissan Qashqai J11. Manual - part 2214

DAS-270

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C1BBC-00 CONTROL MODULE

C1BBC-00 CONTROL MODULE

DTC Description

INFOID:0000000010417023

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Chassis control module

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1.

Turn the ignition switch OFF to ON.

CAUTION:

Be sure to wait of 10 seconds after turning ignition switch OFF or ON.

2.

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “C1BBC-00” detected?

YES

>> Proceed to 

DAS-270, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-41, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010417024

1.

PERFORM SELF-DIAGNOSIS

With CONSULT

1.

Erase self-diagnosis result for “CHASSIS CONTROL”.

2.

Turn the ignition switch OFF and wait for 10 seconds or more.

3.

Turn the ignition switch ON.

4.

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “C1BBC-00” detected?

YES

>> Replace the chassis control module. Refer to 

DAS-312, "Removal and Installation"

.

NO

>> INSPECTION END

DTC

Display Item

(Trouble diagnosis content)

Malfunction detected condition

C1BBC-00

CONTROL MODULE
(Control module)

When a malfunction is detected in chassis control module.

DAS

C1BBD-00 VARIANT CODING

DAS-271

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

C1BBD-00 VARIANT CODING

DTC Description

INFOID:0000000010417025

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Chassis control module

FAIL-SAFE

The following functions are suspended.
• Active Trace Control function
• Active Ride Control function
• Active Engine Brake function

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1.

Turn the ignition switch OFF to ON.

CAUTION:

Be sure to wait of 10 seconds after turning ignition switch OFF or ON.

2.

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “C1BBD-00” detected?

YES

>> Proceed to 

DAS-271, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-41, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010417026

1.

PERFORM SELF-DIAGNOSIS

With CONSULT

1.

Erase self-diagnosis result for “CHASSIS CONTROL”.

2.

Turn the ignition switch OFF and wait for 10 seconds or more.

3.

Turn the ignition switch ON.

4.

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “C1BBD-00” detected?

YES

>> Perform configuration. Refer to 

DAS-241, "Work Procedure"

.

NO

>> INSPECTION END

DTC

Display Item

(Trouble diagnosis content)

Malfunction detected condition

C1BBD-00

VARIANT CODING
(Variant coding)

When variant coding is incomplete.

DAS-272

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C1BC0-00 FRONT RIGHT WHEEL SENSOR

C1BC0-00 FRONT RIGHT WHEEL SENSOR

DTC Description

INFOID:0000000010417027

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Front right wheel sensor
• Front right sensor rotor
• ABS actuator and electric unit (control unit)
• Chassis control module

FAIL-SAFE

The following functions are suspended.
• Active Trace Control function
• Active Ride Control function

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1.

Start the engine.

2.

Drive the vehicle at approx. 30 km/h (19 MPH) or more for approx. 1 minute.

3.

Stop the vehicle.

4.

Turn the ignition switch OFF to ON.

CAUTION:

Be sure to wait of 10 seconds after turning ignition switch OFF or ON.

5.

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “C1BC0-00” detected?

YES

>> Proceed to 

DAS-272, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-41, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010417028

1.

CHECK FRONT RH WHEEL SENSOR SYSTEM

With CONSULT

Perform self-diagnosis for “ABS”.

Is DTC detected?

YES

>> Check the DTC. Refer to 

BRC-53, "DTC Index"

.

NO

>> GO TO 2.

2.

PERFORM SELF-DIAGNOSIS

With CONSULT

1.

Erase self-diagnosis result for “CHASSIS CONTROL”.

2.

Turn the ignition switch OFF and wait for 10 seconds or more.

3.

Turn the ignition switch ON.

4.

Perform “All DTC Reading”.

DTC

Display Item

(Trouble diagnosis content)

Malfunction detected condition

C1BC0-00

FR WHEEL SENSOR
(Front right wheel sensor)

When a malfunction is detected in front right wheel sensor system.

DAS

C1BC0-00 FRONT RIGHT WHEEL SENSOR

DAS-273

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

Is DTC “C1BC0-00”, “U1000-00” or other DTC detected?

YES (“C1BC0-00”)>>Replace the chassis control module. Refer to 

DAS-312, "Removal and Installation"

.

YES (“U1000-00”)>>Refer to 

DAS-286, "Diagnosis Procedure"

.

YES (other DTC)>>Check the DTC.
NO

>> INSPECTION END