Nissan Qashqai J11. Manual - part 2208

DAS-246

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C1B93-00 ENGINE/HEV SYSTEM

YES (“C1B93-00”)>>Replace the chassis control module. Refer to 

DAS-312, "Removal and Installation"

.

YES (“U1000-00”)>>Refer to 

DAS-286, "Diagnosis Procedure"

.

YES (other DTC)>>Check the DTC.
NO

>> INSPECTION END

DAS

C1B94-00 TRANSMISSION SYSTEM

DAS-247

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

C1B94-00 TRANSMISSION SYSTEM

DTC Description

INFOID:0000000010416989

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Transmission system
• TCM
• Chassis control module

FAIL-SAFE

The following functions are suspended.
• Active Ride Control (engine) function
• Active Trace Control function

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1.

Turn the ignition switch OFF to ON.

CAUTION:

Be sure to wait of 10 seconds after turning ignition switch OFF or ON.

2.

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “C1B94-00” detected?

YES

>> Proceed to 

DAS-247, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-41, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010416990

1.

CHECK TRANSMISSION SYSTEM

With CONSULT

Perform self-diagnosis for “TRANSMISSION”.

Is DTC detected?

YES

>> Check the DTC. Refer to 

TM-267, "DTC Index"

 (RE0F10D) or 

TM-485, "DTC Index"

 (RE0F10G).

NO

>> GO TO 2.

2.

PERFORM SELF-DIAGNOSIS

With CONSULT

1.

Erase self-diagnosis result for “CHASSIS CONTROL”.

2.

Turn the ignition switch OFF and wait for 10 seconds or more.

3.

Turn the ignition switch ON.

4.

Perform “All DTC Reading”.

Is DTC “C1B94-00”, “U1000-00” or other DTC detected?

YES (“C1B94-00”)>>Replace the chassis control module. Refer to 

DAS-312, "Removal and Installation"

.

YES (“U1000-00”)>>Refer to 

DAS-286, "Diagnosis Procedure"

.

DTC

Display Item

(Trouble diagnosis content)

Malfunction detected condition

C1B94-00

TM SYSTEM
(Transmission system)

When a malfunction is detected in transmission system.

DAS-248

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C1B94-00 TRANSMISSION SYSTEM

YES (other DTC)>>Check the DTC.
NO

>> INSPECTION END

DAS

C1B95-00 CONTROL MODULE

DAS-249

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

C1B95-00 CONTROL MODULE

DTC Description

INFOID:0000000010416991

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Chassis control module

FAIL-SAFE

The following functions are suspended.
• Active Trace Control function
• Active Ride Control (brake) function

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1.

Turn the ignition switch OFF to ON.

CAUTION:

Be sure to wait of 10 seconds after turning ignition switch OFF or ON.

2.

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “C1B95-00” detected?

YES

>> Proceed to 

DAS-249, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-41, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010416992

1.

PERFORM SELF-DIAGNOSIS

With CONSULT

1.

Erase self-diagnosis result for “CHASSIS CONTROL”.

2.

Turn the ignition switch OFF and wait for 10 seconds or more.

3.

Turn the ignition switch ON.

4.

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “C1B95-00” detected?

YES

>> Replace the chassis control module. Refer to 

DAS-312, "Removal and Installation"

.

NO

>> INSPECTION END

DTC

Display Item

(Trouble diagnosis content)

Malfunction detected condition

C1B95-00

CONTROL MODULE
(Control module)

When a malfunction is detected in chassis control module.