Nissan Juke F15. Manual - part 744

EXL-196

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

EXTERIOR LIGHTING SYSTEM SYMPTOMS

Turn signal lamp does not 
blink

Indicator lamp is normal
(Applicable side per-
forms high flasher activa-
tion)

• Front turn signal lamp
- Front turn signal lamp power sup-

ply/ground circuit

- Front turn signal lamp bulb 
- Front turn signal lamp bulb socket
- BCM
• Side turn signal lamp
- Side turn signal lamp power sup-

ply/ground circuit

- Side turn signal lamp
- BCM
• Rear turn signal lamp
- Rear turn signal lamp power sup-

ply/ground circuit

- Rear turn signal lamp bulb 
- Rear turn signal lamp bulb socket/

harness

- BCM

Turn signal lamp circuit
Refer to 

EXL-182, "Component Func-

tion Check"

.

Indicator lamp is included

• Combination switch input/output 

signal circuit

• Combination switch
• BCM

Combination switch
Refer to 

BCS-92, "Symptom Table"

.

Turn signal indicator lamp 
does not blink
(Turn signal lamp is normal)

One side

Combination meter

—

Both sides
(Always)

• Turn indicator signal
• BCM
• Combination meter

• Combination meter 

Data monitor “TURN IND”

• BCM (FLASHER)

Active test “FLASHER”

Both sides
(Only when activating 
hazard warning lamp 
with ignition switch OFF)

• Combination meter power supply/

ground circuit

• Combination meter

Combination meter
Power supply and ground circuit
Refer to 

MWI-53, "COMBINATION 

METER : Diagnosis Procedure"

.

• Hazard warning lamp does not activate

(Turn signal is normal)

• Hazard warning lamp continues activating

• Hazard switch signal/ground cir-

cuit

• Hazard switch
• BCM

Hazard switch
Refer to 

EXL-188, "Component Func-

tion Check"

.

Symptom

Possible cause

Inspection item

NORMAL OPERATING CONDITION

EXL-197

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

NORMAL OPERATING CONDITION

Description

INFOID:0000000012201768

AUTO LIGHT SYSTEM

The headlamp may not be turned ON/OFF immediately after passing dark area or bright area (short tunnel,

sky bridge, shadowed area, etc.) while using the auto light system. This is caused by for the control difference.

This is normal.

EXL-198

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON

BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON

Description

INFOID:0000000012201769

Both side headlamps (HI) are not turned ON when setting to the lighting switch HI or PASS.

Diagnosis Procedure

INFOID:0000000012201770

1.

COMBINATION SWITCH INSPECTION

Check combination switch. Refer to 

BCS-92, "Symptom Table"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning part.

2.

CHECK HIGH BEAM REQUEST SIGNAL

With CONSULT

1. Turn ignition switch ON.

2. Select “HL HI REQ” in “Data Monitor” mode of “IPDM E/R” using CONSULT.

3. With operating the lighting switch, check the monitor status.

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-37, "Removal and Installation"

.

NO

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

Monitor item

Condition

Monitor status

HL HI REQ

Lighting switch
(2ND)

HI or PASS

On

LO

Off

BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON

EXL-199

< SYMPTOM DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON

Description

INFOID:0000000012201771

Both side headlamps (LO) are not turned ON in any condition.

Diagnosis Procedure

INFOID:0000000012201772

1.

COMBINATION SWITCH INSPECTION

Check combination switch. Refer to 

BCS-92, "Symptom Table"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning part.

2.

CHECK LOW BEAM REQUEST SIGNAL

With CONSULT

1. Turn ignition switch ON.

2. Select “HL LO REQ” in “Data Monitor” mode of “IPDM E/R” using CONSULT.

3. With operating the lighting switch, check the monitor status.

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-37, "Removal and Installation"

.

NO

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

Monitor item

Condition

Monitor status

HL LO REQ

Lighting switch

2ND

On

OFF

Off