Nissan Juke F15. Manual - part 738

EXL-172

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

TAIL LAMP CIRCUIT

2. Disconnect IPDM E/R connector and rear combination lamp connector.

3. Check continuity between IPDM E/R harness connector and rear combination lamp harness connector.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK TAIL LAMP GROUND CIRCUIT

Check continuity between rear combination lamp harness connector and ground.

Is the inspection result normal?

YES-1 >> Stop lamp / tail lamp (Bulb side): GO TO 5.

YES-2 >> Tail lamp (LED side): Check the corresponding tail lamp harness, and if check result is normal,

replace the corresponding rear combination lamp. Refer to 

EXL-220, "Removal and Installation"

.

NO

>> Repair or replace harness.

5.

CHECK STOP LAMP / TAIL LAMP BULB

Check the applicable stop lamp / tail lamp bulb.
Is the inspection result normal?

YES

>> Check the corresponding stop lamp / tail lamp bulb socket and harness. Repair or replace if nec-

essary.

NO

>> Repair or replace the corresponding stop lamp / tail lamp bulb. Refer to 

EXL-220, "Replacement"

.

IPDM E/R

Rear combination lamp

Continuity

Connector

Terminal

Connector

Terminal

RH

E14

44

B59

2

Existed

LH

B80

Rear combination lamp

—

Continuity

Connector

Terminal

RH

B59

3

Ground

Existed

LH

B80

LICENSE PLATE LAMP CIRCUIT

EXL-173

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

LICENSE PLATE LAMP CIRCUIT

Component Function Check

INFOID:0000000012201752

1.

CHECK TAIL LAMP OPERATION

Check that the tail lamp is turned ON.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Check tail lamp circuit. Refer to 

EXL-171, "Component Function Check"

.

2.

CHECK LICENSE PLATE LAMP OPERATION

With CONSULT

1. Turn ignition switch ON.

2. Select “EXTERNAL LAMPS” in “Active Test” mode of “IPDM E/R” using CONSULT.

3. With operating the test items, check that the license plate lamp is turned ON.

Without CONSULT

1. Start IPDM E/R auto active test. Refer to 

PCS-12, "Diagnosis Description"

.

2. Check that the license plate lamp is turned ON.
Is the inspection result normal?

YES

>> License plate lamp circuit is normal.

NO

>> Refer to 

EXL-173, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012201753

1.

CHECK LICENSE PLATE LAMP POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R connector and back door opener switch connector.

3. Check continuity between IPDM E/R harness connector and back door opener switch harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace harness.

2.

CHECK LICENSE PLATE LAMP GROUND CIRCUIT

Check continuity between back door opener switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK LICENSE PLATE LAMP BULB

Check the applicable license plate lamp bulb.
Is the inspection result normal?

TAIL

: License plate lamp ON

Off

: License plate lamp OFF

IPDM E/R

Back door opener switch

Continuity

Connector

Terminal

Connector

Terminal

E14

44

D107

5

Existed

Back door opener switch

—

Continuity

Connector

Terminal

D107

6

Ground

Existed

EXL-174

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

LICENSE PLATE LAMP CIRCUIT

YES

>> Check the corresponding license plate lamp bulb socket and harness. Repair or replace if neces-

sary.

NO

>> Replace the corresponding license plate lamp bulb. Refer to 

EXL-224, "Replacement"

.

DAYTIME RUNNING LIGHT RELAY CIRCUIT

EXL-175

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

DAYTIME RUNNING LIGHT RELAY CIRCUIT

Component Function Check

INFOID:0000000012201754

1.

CHECK DAYTIME RUNNING LIGHT OPERATION

With CONSULT

1. Select “HEAD LAMP” of “BCM” using CONSULT.

2. Select “DAYTIME RUNNING LIGHT” in “Active Test” mode.

3. With operating the test items, check that the daytime running light is turned ON [Headlamp (HI) at approx-

imately half illumination].

Is the inspection result normal?

YES

>> Daytime running light relay circuit is normal.

NO

>> Refer to 

EXL-175, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012201755

1.

CHECK DAYTIME RUNNING LIGHT RELAY FUSE

1. Turn ignition switch OFF.

2. Check that the following fuses are not blown (open).

Is the fuse blown (open)?

YES

>> Replace the blown fuse after repairing the affected circuit if a fuse is blown (open).

NO

>> GO TO 2.

2.

CHECK DAYTIME RUNNING LIGHT RELAY POWER SUPPLY

1. Remove daytime running light relay.

2. Check voltage between daytime running light relay harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK DAYTIME RUNNING LIGHT RELAY

Check daytime running light relay. Refer to 

EXL-176, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace daytime running light relay.

4.

CHECK DAYTIME RUNNING LIGHT RELAY CONTROL SIGNAL

With CONSULT

1. Install daytime running light relay.

2. Turn ignition switch ON.

3. Select “HEAD LAMP” of “BCM” using CONSULT.

4. Select “DAYTIME RUNNING LIGHT” in “Active Test” mode.

On

: Daytime running light ON [Headlamp (HI) at approximately half illumination]

Off

: Daytime running light OFF

Unit

Fuse No.

Capacity

Daytime running light relay

#24

10 A

+

-

Voltage

(Approx.)

Daytime running light relay

Connector

Terminal

E65

1

Ground

Battery voltage

5