Nissan Juke F15. Manual - part 1336

TM-534

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

SHIFT POSITION INDICATOR CIRCUIT

SHIFT POSITION INDICATOR CIRCUIT

Component Parts Function Inspection

INFOID:0000000012201227

1.

CHECK SHIFT POSITION INDICATOR

1. Start the engine.

2. Shift selector lever.

3. Check that the selector lever position and the shift position indicator on the combination meter are identi-

cal.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Go to 

TM-534, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012201228

1.

CHECK TCM INPUT/OUTPUT SIGNAL 

With CONSULT

1. Start the engine.

2. Select “Data Monitor” in “TRANSMISSION”.

3. Select “RANGE”. 

4. Shift selector lever.

5. Check that selector lever position, “RANGE” on CONSULT screen, and shift position indicator display on

combination meter are identical.

Is the check result normal?

YES

>> INSPECTION END

NO-1 (“RANGE” is changed but is not displayed on shift position indicator.>>Check “Self Diagnostic Result”

in “TRANSMISSION”.

NO-2 (“RANGE” and shift position indicator are different.)>>Check “Self Diagnostic Result” in “TRANSMIS-

SION”.

NO-3 (Specific “RANGE” is not displayed on shift position indicator.)>>Check “Self Diagnostic Result” in

“METER/M&A”.

SHIFT LOCK SYSTEM

TM-535

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

SHIFT LOCK SYSTEM

Component Function Check

INFOID:0000000012201229

1.

CHECK SHIFT LOCK OPERATION (PART 1)

1. Turn ignition ON.

2. Shift the selector lever to “P” position.

3. Attempt to shift the selector lever to any other than position with the brake pedal released.
Can the selector lever be shifted to any other position?

YES

>> Go to 

TM-535, "Diagnosis Procedure"

.

NO

>> GO TO 2.

2.

CHECK SHIFT LOCK OPERATION (PART 2)

Attempt to shift the selector lever to any other than position with the brake pedal depressed.
Can the selector lever be shifted to any other position?

YES

>> INSPECTION END

NO

>> Go to 

TM-535, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012201230

1.

CHECK POWER SOURCE (PART 1)

1. Turn ignition switch OFF.

2. Disconnect stop lamp switch connector

3. Turn ignition switch ON.

4. Check the voltage between the stop lamp switch harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> GO TO 8.

2.

CHECK STOP LAMP SWITCH (PART 1)

Check stop lamp switch. Refer to 

TM-536, "Component Inspection (Stop Lamp Switch)"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 9.

3.

CHECK CIRCUIT BETWEEN STOP LAMP SWITCH AND CVT SHIFT SELECTOR

1. Disconnect CVT shift selector connector

2. Check the continuity between the stop lamp switch harness connector terminal and the CVT shift selector

harness connector terminal.

3. Also check short circuit in harness.
Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the malfunctioning parts.

4.

CHCK GROUND CIRCUIT

+

−

Voltage

Stop lamp switch

Connector

Terminal

E102

3

Ground

Battery voltage

Stop lamp switch

CVT shift selector

Continuity

Connector

Terminal

Connector

Terminal

E102

4

M57

3

Existed

TM-536

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

SHIFT LOCK SYSTEM

Check the continuity between the CVT shift selector harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace the malfunctioning parts.

5.

CHECK PART POSITION SWITCH

1. Disconnect park position switch connector.

2. Check park position switch. Refer to 

TM-537, "Component Inspection (Park Position Switch)"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace the malfunctioning parts.

6.

CHECK SHIFT LOCK SOLENOID

1. Disconnect shift lock solenoid connector.

2. Check shift lock solenoid. Refer to 

TM-537, "Component Inspection (Shift Lock Solenoid)"

.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace the malfunctioning parts.

7.

CHECK CVT SHIFT SELECTOR HARNESS

Check CVT shift selector harness. Refer to 

TM-537, "Component Inspection (CVT Shift Selector Harness)"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair or replace the malfunctioning parts.

8.

DETECT MALFUNCTIONING ITEM

Check the following items:

• Open circuit or short circuit in harness between ignition switch and stop lamp switch connector. Refer to 

PG-

43, "Wiring Diagram - IGNITION POWER SUPPLY -"

.

• Ignition switch

• 10A fuse [No.3, fuse block (J/B)]. Refer to 

PG-80, "Fuse, Connector and Terminal Arrangement"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair or replace the malfunctioning parts.

9.

CHECK INSTALLATION POSITION OF STOP LAMP SWITCH

Adjust stop lamp switch position. Refer to 

BR-9, "Inspection and Adjustment"

.

>> GO TO 10.

10.

CHECK STOP LAMP SWITCH (PART 2)

Check stop lamp switch. Refer to 

TM-536, "Component Inspection (Stop Lamp Switch)"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair or replace the malfunctioning parts.

Component Inspection (Stop Lamp Switch)

INFOID:0000000012201231

1.

CHECK STOP LAMP SWITCH

Check continuity between the stop lamp switch connector terminals.

CVT shift selector

—

Continuity

Connector

Terminal

M57

4

Ground

Existed

SHIFT LOCK SYSTEM

TM-537

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace stop lamp switch. Refer to 

BR-20, "Exploded View"

.

Component Inspection (Park Position Switch)

INFOID:0000000012201232

1.

CHECK PARK POSITION SWITCH

Check continuity between park position switch connector terminals.

CAUTION:

• Connect the fuse between the terminals when applying the voltage.

• Never cause shorting between terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace park position switch. Refer to 

TM-547, "Disassembly and Assembly"

.

Component Inspection (Shift Lock Solenoid)

INFOID:0000000012201233

1.

CHECK SHIFT LOCK SOLENOID

Apply voltage to terminals of shift lock solenoid connector and check that shift lock solenoid is activated.

CAUTION:

• Connect the fuse between the terminals when applying the voltage.

• Never cause shorting between terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace shift lock unit. Refer to 

TM-547, "Disassembly and Assembly"

.

Component Inspection (CVT Shift Selector Harness)

INFOID:0000000012201234

1.

CHECK CVT SHIFT SELECTOR HARNESS (PART 1)

Check continuity between CVT shift selector harness connector terminal and shift lock solenoid harness con-

nector terminal.

Is the inspection result normal?

Stop lamp switch

Condition

Continuity

Terminal

3 – 4

Depressed brake pedal

Yes

Released brake pedal

No

Park position switch

Condition

Continuity

Terminal

1 – 2

Shift selector lever to “P” position.

Existed

Other than above

Not existed

Shift lock solenoid

Condition

Status

+ (fuse)

−

Terminal

1

2

Apply battery voltage be-
tween terminals 1 and 2.

Shift lock solenoid operates

CVT shift selector

Shift lock solenoid

Continuity

Connector

Terminal

Connector

Terminal

M324

3

M326

1

Existed