Infiniti QX56 (Z62). Manual - part 394

DLK-42

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (BCM)

SELF-DIAG RESULT

Refer to 

BCS-57, "DTC Index"

.

DATA MONITOR

AUTO LOCK SET

Auto door lock operation time can be changed in this mode
• MODE 1: OFF
• MODE 2: 30 sec
• MODE 3: 1 minute
• MODE 4: 2 minutes
• MODE 5: 3 minutes
• MODE 6: 4 minutes
• MODE 7: 5 minutes

HORN WITH KEYLESS LOCK

Horn reminder function mode by Intelligent Key button can be selected from the following with 
this mode
• On: Operate
• Off: Non-operation

PW DOWN SET

Unlock button pressing time on Intelligent Key button can be selected from the following with 
this mode
• MODE 1: 3 sec
• MODE 2: Non-operation
• MODE 3: 5 sec

WELCOME LIGHT SELECT

Welcome light function mode can be selected from the following with this mode
• Puddle/Outside Handle
• Room lamp
• Head & Tail Lamps (this item is displayed, but cannot be used)
• Heart Beat

WELCOME LIGHT OP SET

Welcome light function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation

Monitor item

Description

Monitor Item

Condition

REQ SW -DR

Indicates [On/Off] condition of door request switch (driver side)

REQ SW -AS

Indicates [On/Off] condition of door request switch (passenger side)

REQ SW -BD/TR

Indicates [On/Off] condition of back door request switch

PUSH SW

Indicates [On/Off] condition of push-button ignition switch

CLUTCH SW

NOTE:
This item is displayed, but cannot be monitored 

BRAKE SW 1

Indicates [On/Off]* condition of stop lamp switch power supply

BRAKE SW 2

Indicates [On/Off] condition of stop lamp switch

DETE/CANCL SW

Indicates [On/Off] condition of P position

SFT PN/N SW

Indicates [On/Off] condition of P or N position

S/L -LOCK

Indicates [On/Off] condition of steering lock unit (LOCK)

S/L -UNLOCK

Indicates [On/Off] condition of steering lock unit (UNLOCK)

S/L RELAY -F/B

Indicates [On/Off] condition of steering lock relay

UNLK SEN -DR

Indicates [On/Off] condition of driver door UNLOCK status

PUSH SW -IPDM

Indicates [On/Off] condition of push-button ignition switch

IGN RLY1 -F/B

Indicates [On/Off] condition of ignition relay 1

DETE SW -IPDM

Indicates [On/Off] condition of P position

SFT PN -IPDM

Indicates [On/Off] condition of P or N position

SFT P -MET

Indicates [On/Off] condition of P position

SFT N -MET

Indicates [On/Off] condition of N position

ENGINE STATE

Indicates [Stop/Stall/Crank/Run] condition of engine states

DIAGNOSIS SYSTEM (BCM)

DLK-43

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

*: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.

ACTIVE TEST

S/L LOCK-IPDM

Indicates [On/Off] condition of steering lock unit (LOCK)

S/L UNLK-IPDM

Indicates [On/Off] condition of steering lock unit (UNLOCK)

S/L RELAY-REQ

Indicates [On/Off] condition of steering lock relay

VEH SPEED 1

Display the vehicle speed signal received from combination meter by numerical value [Km/h]

VEH SPEED 2

Display the vehicle speed signal received from ABS or VDC or TCM by numerical value [Km/h]

DOOR STAT-DR

Indicates [LOCK/READY/UNLK] condition of unlock sensor

DOOR STAT-AS

Indicates [LOCK/READY/UNLK] condition of passenger side door status

ID OK FLAG

Indicates [Set/Reset] condition of key ID

PRMT ENG STRT

Indicates [Set/Reset] condition of engine start possibility

PRMT RKE STRT

NOTE:
This item is displayed, but cannot be monitored 

TRNK/HAT MNTR

NOTE:
This item is displayed, but cannot be monitored 

RKE-LOCK

Indicates [On/Off] condition of LOCK signal from Intelligent Key

RKE-UNLOCK

Indicates [On/Off] condition of UNLOCK signal from Intelligent Key

RKE-TR/BD

NOTE:
This item is displayed, but cannot be monitored 

RKE-PANIC

Indicates [On/Off] condition of PANIC button of Intelligent Key

RKE-MODE CHG

Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key

RKE OPE COUN1

When remote keyless entry receiver receives the signal transmitted while operating on Intelli-
gent Key, the numerical value start changing

RKE OPE COUN2

NOTE:
This item is displayed, but cannot be monitored 

Monitor Item

Condition

Test item

Description

BATTERY SAVER

This test is able to check interior room lamp operation
• On: Operate
• Off: Non-operation

OUTSIDE BUZZER

This test is able to check Intelligent Key warning buzzer operation
• On: Operate
• Off: Non-operation

INSIDE BUZZER

This test is able to check warning chime in combination meter operation
• Take Out: Take away warning chime sounds when CONSULT-III screen is touched
• Key: Key warning chime sounds when CONSULT-III screen is touched
• Knob: OFF position warning chime sounds when CONSULT-III screen is touched
• Off: Non-operation

INDICATOR

This test is able to check warning lamp operation
• KEY ON: “KEY” Warning lamp illuminates when CONSULT-III screen is touched
• KEY IND: “KEY” Warning lamp blinks when CONSULT-III screen is touched
• Off: Non-operation

INT LAMP

This test is able to check interior room lamp operation
• On: Operate
• Off: Non-operation

DLK-44

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (BCM)

TRUNK

TRUNK : CONSULT-III Function (BCM - TRUNK)

INFOID:0000000006225857

DATA MONITOR

LCD

This test is able to check meter display information
• Engine start information displays when “BP N” on CONSULT-III screen is touched
• Engine start information displays when “BP I” on CONSULT-III screen is touched
• Key ID warning displays when “ID NG” on CONSULT-III screen is touched
• Steering lock information displays when “ROTAT” on CONSULT-III screen is touched
• P position warning displays when “SFT P” on CONSULT-III screen is touched
• INSRT: This item is displayed, but cannot be monitored 
• BATT: This item is displayed, but cannot be monitored 
• Take away through window warning displays when “NO KY” on CONSULT-III screen is 

touched

• Take away warning display when “OUTKEY” on CONSULT-III screen is touched
• OFF position warning display when “LK WN” on CONSULT-III screen is touched

FLASHER

This test is able to check security hazard lamp operation
The hazard lamps are activated after “LH/RH/Off” on CONSULT-III screen is touched

P RANGE

This test is able to check A/T shift selector power supply
• On: Operate
• Off: Non-operation

ENGINE SW ILLUMI

This test is able to check push-button ignition switch illumination operation
Push-ignition switch illumination illuminates when “ON” on CONSULT-III screen is touched

LOCK INDICATOR

This test is able to check LOCK indicator (push-button ignition switch) operation
• On: Operate
• Off: Non-operation

ACC INDICATOR

This test is able to check ACC indicator (push-button ignition switch) operation
• On: Operate
• Off: Non-operation

IGNITION ON IND

This test is able to check ON indicator (push-button ignition switch) operation
• On: Operate
• Off: Non-operation

HORN

This test is able to check horn operation
• On: Operate
• Off: Non-operation

TRUNK/BACK DOOR

NOTE:
This item is displayed, but cannot be used

Test item

Description

Monitor Item

Contents

PUSH SW

Indicates [On/Off] condition of push switch

UNLK SEN -DR

Indicates [On/Off] condition of unlock sensor

VEH SPEED 1

Indicates [Km/h] condition of vehicle speed signal from combination meter

TR/BD OPEN SW

Indicates [On/Off] condition of back door opener switch

TRNK/HAT MNTR

NOTE:
This item is displayed, but cannot be monitored

RKE-TR/BD

NOTE:
This item is displayed, but cannot be monitored

DIAGNOSIS SYSTEM (AUTOMATIC BACK DOOR CONTROL UNIT)

DLK-45

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

DIAGNOSIS SYSTEM (AUTOMATIC BACK DOOR CONTROL UNIT)

CONSULT-III Function (AUTOMATIC BACK DOOR CONTROL UNIT)

INFOID:0000000006225858

APPLICATION ITEM

CONSULT-III performs the following functions via CAN communication with automatic back door control unit.

DATA MONITOR

SELF-DIAG RESULT

Refer to 

DLK-50, "DTC Index"

.

Diagnosis mode

Function Description

Self Diagnostic Result

Displays the diagnosis results judged by automatic back door control unit

CAN Diag Support Monitor

Monitors the reception status of CAN communication viewed from automatic back door 
control unit

Data Monitor

The automatic back door control unit input/output signals are displayed

Ecu Identification

The automatic back door control unit part number is displayed

Monitor Item

Unit

Description

VHCL SPEED MTR

[km/h]

Display the vehicle speed signal received from combination meter by nu-
merical value

VHCL SPEED ABS

[km/h]

Display the vehicle speed signal received from ABS actuator and electrical 
unit by numerical value

VHCL SPEED SIG

[NORMAL/ER-

ROR]

Indicates condition of vehicle speed from automatic back door control unit

MAIN SW

[ON/OFF]

Indicates condition of automatic back door main switch

AUTO BD SW

[ON/OFF]

Indicates condition of automatic back door switch

BK DOOR CL SW

[ON/OFF]

Indicates condition of automatic back door close switch

UNLOCK SEN DR

[ON/OFF]

Indicates condition of unlock sensor

OPEN SW

[ON/OFF]

Indicates condition of open switch

CLOSE SW

[ON/OFF]

Indicates condition of close switch

HALF LATCH SW

[ON/OFF]

Indicates condition of half latch switch

TOUCH SEN RH

[ON/OFF/OPEN]

Indicates condition of touch sensor RH

TOUCH SEN LH

[ON/OFF/OPEN]

Indicates condition of touch sensor LH

P RANGE IND

[ON/OFF]

Indicates condition of P range signal from combination meter

RKE REQ

[OFF/MOVE/

REV]

Indicates condition of remote keyless entry signal from BCM

IGN SW

[ON/OFF]

Indicates condition of IGN power supply

ENCODER A

[LO/HI]

Indicates condition of encoder signal from encoder A

ENCODER B

[LO/HI]

Indicates condition of encoder signal from encoder B

BD OPENER SW

[ON/OFF]

Indicates condition of back door opener switch

UNLOCK SEN BD

[LOCK/

UNLOCK]

NOTE:
This item is displayed, but cannot be monitored

DESTINATION

[JPN/NAM]

Indicates specification of destination of the automatic back door system

HAZARD

[ON/OFF]

Indicates specification of hazard warning