Infiniti FX35, FX50 (S51). Manual - part 1002

EXL-4

Removal and Installation  .......................................

231

Replacement .........................................................

231

OPTICAL SENSOR  .........................................

233

Exploded View  .......................................................

233

Removal and Installation  .......................................

233

LIGHTING & TURN SIGNAL SWITCH  ............

234

Exploded View  .......................................................

234

HEADLAMP AIMING SWITCH  ........................

235

Exploded View  .......................................................

235

Removal and Installation  .......................................

235

HAZARD SWITCH  ...........................................

236

Exploded View  .......................................................

236

AFS CONTROL UNIT  ......................................

237

Exploded View  .......................................................

237

Removal and Installation  .......................................

237

STEERING ANGLE SENSOR  .........................

238

Removal and Installation  .......................................

238

HEIGHT SENSOR ............................................

239

Exploded View  .......................................................

239

Removal and Installation  .......................................

239

REAR COMBINATION LAMP  ..........................

240

Exploded View  ......................................................

240

Removal and Installation .......................................

240

Replacement .........................................................

241

HIGH-MOUNTED STOP LAMP  ........................

242

Exploded View  ......................................................

242

Removal and Installation .......................................

242

BACK-UP LAMP ..............................................

243

Exploded View  ......................................................

243

Removal and Installation .......................................

243

Replacement .........................................................

243

LICENSE PLATE LAMP ...................................

245

Exploded View  ......................................................

245

Removal and Installation .......................................

245

Replacement .........................................................

245

SERVICE DATA AND SPECIFICATIONS 
(SDS) .........................................................

246

SERVICE DATA AND SPECIFICATIONS 
(SDS) ................................................................

246

Bulb Specifications ................................................

246

DIAGNOSIS AND REPAIR WORKFLOW

EXL-5

< BASIC INSPECTION >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

BASIC INSPECTION

DIAGNOSIS AND REPAIR WORKFLOW

Work Flow

INFOID:0000000005244651

OVERALL SEQUENCE

DETAILED FLOW

1.

INTERVIEW FOR MALFUNCTION

Interview the symptom to the customer.

JPLIA0313GB

EXL-6

< BASIC INSPECTION >

[XENON TYPE]

DIAGNOSIS AND REPAIR WORKFLOW

>> GO TO 2.

2.

SYMPTOM CHECK

Check the symptom from the customer's information.

>> GO TO 3.

3.

BASIC INSPECTION

Check the operation of each part. Check that any symptom occurs other than the interviewed symptom.

>> GO TO 4.

4.

SELF-DIAGNOSIS WITH CONSULT-III

Perform the self-diagnosis with CONSULT-III. Check that any DTC is detected.
Is any DTC detected?

YES

>> GO TO 5.

NO

>> GO TO 6.

5.

TROUBLE DIAGNOSIS BY DTC

Perform the trouble diagnosis for the detected DTC. Specify the malfunctioning part.

>> GO TO 9.

6.

FAIL-SAFE ACTIVATION CHECK

Check that the symptom is applied to the fail-safe activation.
Does the fail-safe activate?

YES

>> GO TO 7.

NO

>> GO TO 8.

7.

SYSTEM DIAGNOSIS

Perform the system diagnosis for the system that the fail-safe activates. Specify the malfunctioning part.

>> GO TO 9.

8.

SYMPTOM DIAGNOSIS

Perform the symptom diagnosis. Specify the malfunctioning part.

>> GO TO 9.

9.

MALFUNCTION PART REPAIR

Repair or replace the malfunctioning part.

>> GO TO 10.

10.

REPAIR CHECK (SELF-DIAGNOSIS WITH CONSULT-III)

Perform the self-diagnosis with CONSULT-III. Check that any DTC is not detected. Erase DTC if DTC is
detected before the repair. Check that DTC is not detected again.

Is any DTC detected?

YES

>> GO TO 5.

NO

>> GO TO 11.

11.

REPAIR CHECK (OPERATION CHECK)

Check the operation of each part.
Does it operate normally?

YES

>> INSPECTION END

NO

>> GO TO 3.

INSPECTION AND ADJUSTMENT

EXL-7

< BASIC INSPECTION >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

INSPECTION AND ADJUSTMENT

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description

INFOID:0000000005244652

Perform “LEVELIZER ADJUSTMENT” with CONSULT-III when replacing the height sensor. 

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement

INFOID:0000000005244653

1.

LEVELIZER ADJUSTMENT

Perform “LEVELIZER ADJUSTMENT”.

>> Refer to 

EXL-7, "LEVELIZER ADJUSTMENT : Special Repair Requirement"

.

LEVELIZER ADJUSTMENT

LEVELIZER ADJUSTMENT : Description

INFOID:0000000005244654

Perform “LEVELIZER ADJUSTMENT” when installing, removing, and replacing the height sensor and the sus-
pension components.

LEVELIZER ADJUSTMENT : Special Repair Requirement

INFOID:0000000005244655

1.

CHECK VEHICLE CONDITION

1.

Park the vehicle in the straight-forward position.

2.

Unload the vehicle (no passenger aboard).

>> GO TO 2.

2.

LEVELIZER ADJUSTMENT

CONSULT-III WORK SUPPORT

1.

Select "LEVELIZER ADJUSTMENT" of ADAPTIVE LIGHT work support item.

2.

Select "START".

3.

When "ADJUSTMENT IS COMPLETED", select "END".

CAUTION:

If "CAN NOT BE TESTED" is indicated, AFS control unit detects that the height sensor signal
changes. The levelizer adjustment is cancelled. In this case, turn the ignition switch OFF to pre-
vent the vehicle from the height change. Perform the levelizer adjustment again.

Is the levelizer adjustment completed?

YES

>> GO TO 3.

NO

>> Perform the levelizer adjustment again.

3.

SELF-DIAGNOSIS RESULT CHECK

Perform self-diagnosis with CONSULT-III. Check that any DTC is not detected.

Is any DTC detected?

YES

>> GO TO 2.

NO

>> Levelizer adjustment completed