Chrysler New Yorker. Manual - part 504

TEST 17A

REPAIRING

(

DECKLID RELEASE SWITCH FAILURE

(

TROUBLE CODE

Perform TEST 1A Before Proceeding

FIG. 1

P

O

W

E

R

D

O
O

R

L

O

C
K

S
Y
S

T

E

M

614

TEST 17A

REPAIRING

(

DECKLID RELEASE SWITCH FAILURE

(

TROUBLE CODE

Perform TEST 1A Before Proceeding

*Perform Verification TEST VER-2A.

**Check connectors - Clean / repair as necessary.

NOTE: FOR LOCATION DISCONNECT 

THE

OF ALL COMPONENTS.

DECKLID RELEASE

START TEST 17A. 

SWITCH HARNESS

CONNECTOR.** 

SEE GENERAL INFO 4.0

FIG. 1

CYCLE THE IGNITION 

USING THE DRB, SWITCH 

OFF THEN 

ERASE THE TROUBLE

ON.

CODE.

WAIT AT LEAST 30 

SECONDS. 

DID THE DECKLID

USING THE DRB, RELEASE SWITCH 

NO 

REPLACE THE

READ DTC’s. 

FAILURE CODE 

DECKLID RELEASE

REAPPEAR?

SWITCH.* 

YES

DISCONNECT THE

USING A VOLTMETER, 

REPAIR THE DECKLID

BODY CONTROL

MEASURE THE

IS ANY VOLTAGE

YES

RELEASE SWITCH 

MODULE C1 HARNESS

DECKLID RELEASE

PRESENT? 

OUTPUT CIRCUIT FOR

CONNECTOR.** 

SWITCH OUTPUT CKT. 

A SHORT TO 

FIG. 1

VOLTAGE.*

NO 

REPLACE THE BODY 
CONTROL MODULE.* 

P

O

W

E

R

D

O
O

R

L

O

C
K

S
Y
S

T

E

M

615

TEST 18A

REPAIRING

(

DECKLID RELEASE SOLENOID OUTPUT FAILURE

(

TROUBLE CODE

Perform TEST 1A Before Proceeding

FIG. 1

FIG. 2

P

O

W

E

R

D

O
O

R

L

O

C
K

S
Y
S

T

E

M

616

TEST 18A

REPAIRING

(

DECKLID RELEASE SOLENOID OUTPUT FAILURE

(

TROUBLE CODE

Perform TEST 1A Before Proceeding

*Perform Verification TEST VER-2A.

**Check connectors - Clean / repair as necessary.

NOTE: FOR LOCATION KEY OFF. 

DISCONNECT 

OF ALL COMPONENTS.

THE DECKLID RELEASE

START TEST 18A. 

SOLENOID HARNESS

CONNECTOR.** 

SEE GENERAL INFO 4.0

FIG. 1

WITH AN OHMMETER,

MEASURE BETWEEN

IS 

THE RESISTANCE NO REPAIR 

THE OPEN 

GROUND AND THE

BELOW 5.0 OHMS?

GROUND CIRCUIT.*

GROUND CIRCUIT. 

FIG. 1

YES

KEY ON. WITH A TEST 

LIGHT CONNECTED TO 

IS THE TEST LIGHT

YES

CONTINUE TEST 

GROUND, PROBE THE

ILLUMINATED? 18A ON 

THE NEXT 

DECKLID RELEASE

PAGE.

CONTROL CKT. FIG. 1

NO 

WITH THE DRB, 

DOES THE TEST 

LEAVE THE TEST ACTUATE THE

LIGHT FLASH ON 

AND

YES

REPLACE THE

LIGHT CONNECTED. DECKLID RELEASE

OFF AS 

THE

DECKLID RELEASE

SWITCH.

SOLENOID IS 

SOLENOID.* 

ACTUATED?

NO 

STOP THE

WITH AN OHMMETER,

REPAIR THE DECKLID

ACTUATION. MEASURE BETWEEN

IS 

THE RESISTANCE 

YES

RELEASE CONTROL

TURN THE IGNITION 

GROUND AND THE

BELOW 5.0 OHMS?

CIRCUIT FOR A SHORT

OFF. 

DECKLID RELEASE

TO GROUND. IF OK,

CONTROL CKT. FIG. 1

REPLACE THE J/B.*

NO 

CONNECT A JUMPER REMOVE 

THE BODY 

WIRE BETWEEN GROUND 

CONTROL MODULE 

AND THE DECKLID

FROM THE JUNCTION 

RELEASE CONTROL CKT. BLOCK. 

FIG. 1

JUNCTION BLOCK

REPAIR THE OPEN 

WITH AN OHMMETER,

20-WAY INTERNAL 

IS THE RESISTANCE 

NO 

DECKLID RELEASE

MEASURE BETWEEN

CONNECTOR CAVITY 8. 

BELOW 5.0 OHMS?

CONTROL CIRCUIT. 

GROUND AND THE ...

IF OK, REPLACE THE

FIG. 2

JUNCTION BLOCK.*

YES

REPLACE THE BODY 
CONTROL MODULE.* 

P

O

W

E

R

D

O
O

R

L

O

C
K

S
Y
S

T

E

M

617