|
|
Content .. 1508 1509 1510 1511 ..
Fig. 14: View Of Front Disc Brake Components Callout Component Name CAUTION: Refer to Brake Dust Caution . NOTE: Support the brake caliper with heavy mechanic wire, or equivalent, whenever it is separated from its
2008 Chevrolet Silverado 1500 2008 BRAKES Disc Brakes - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
Preliminary Procedures 1. Inspect the fluid level in the brake master cylinder reservoir. 2. If the brake fluid level is midway between the maximum-full point and the minimum allowable level, no brake fluid needs to be removed before proceeding. 3. If the brake fluid level is higher than midway between the maximum-full point and the minimum allowable level, remove brake fluid to the midway point before proceeding. 4. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle . 5. Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation . 1 Brake Caliper Guide Pin Bolt Procedure 1. DO NOT use any air tools to remove or install the brake caliper guide pin bolts. Use hand tools ONLY. 2. Install an open end wrench to hold the caliper guide pin in line with the brake caliper while removing or installing the caliper guide pin bolts. DO 3. Ensure the brake caliper guide pin seal is fully seated in the groove of the brake caliper guide pin and the guide pin slides freely in caliper bracket Tighten: 100 N.m (74 lb ft) NOTE: Refer to Fastener Notice . 2 Brake Caliper Procedure 1. Install 2 large C-clamps over the top of the caliper housing and against the back of the outboard brake pad. 2. Slowly and evenly tighten the C-clamps until the caliper pistons are completely retracted into the brake caliper bores. 3. Remove the C-clamps.
2008 Chevrolet Silverado 1500 2008 BRAKES Disc Brakes - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
REAR DISC BRAKE PADS REPLACEMENT (JH6, JH7) 4. Without disconnecting the brake hose, pivot the brake caliper upward. 5. Support the brake caliper with heavy mechanics wire or equivalent. 3 Disc Brake Pad (Qty: 2) 4 Brake Pad Shim (Qty: 2) Procedure 1. Discard the brake pad shims. 2. Thoroughly clean the brake pad hardware mating surfaces of the caliper bracket of any debris and corrosion. 3. Apply a very thin coating of high temperature silicone brake lubricant to the pad hardware mating surfaces of the caliper bracket only. 4. After the installation is complete and with the engine OFF, gradually apply the brake pedal to approximately 2/3 of its travel distance. 5. Slowly release the brake pedal. 6. Wait 15 seconds, then repeat steps 4-5 until a firm brake pedal is obtained. This will properly seat the brake caliper pistons and brake pads. 7. Fill the master cylinder to the proper level. Refer to Master Cylinder Reservoir Filling . 8. Burnish the brake pads and rotors. Refer to Brake Pad and Rotor Burnishing.
2008 Chevrolet Silverado 1500 2008 BRAKES Disc Brakes - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
Fig. 15: View Of Rear Disc Brake Components Callout Component Name Preliminary Procedures 1. Inspect the fluid level in the brake master cylinder reservoir. 2. If the brake fluid level is midway between the maximum-full point and the minimum allowable level, no brake fluid needs to be removed before proceeding. 3. If the brake fluid level is higher than midway between the maximum-full point and the minimum allowable level, remove brake fluid to the midway point before proceeding. 4. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle . CAUTION: Refer to Brake Dust Caution . NOTE: Support the brake caliper with heavy mechanic wire, or equivalent, whenever it is separated from its
2008 Chevrolet Silverado 1500 2008 BRAKES Disc Brakes - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra & Silverado
Content .. 1508 1509 1510 1511 ..
|
|
|