Nissan Leaf (2023 year). Manual in english - page 22

 

  Index      Manuals     Nissan Leaf (2023 year). Manual in english

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

 

 

 

Content      ..     20      21      22      23     ..

 

 

 

Nissan Leaf (2023 year). Manual in english - page 22

 

 

WARNING

Failure to follow the warnings and in-
structions for proper use of the LDW
system could result in serious injury or
death.

This system is only a warning device
to inform the driver of a potential un-
intended lane departure. It will not
steer the vehicle or prevent loss of
control. It is the driver’s responsibility
to stay alert, drive safely, keep the
vehicle in the traveling lane, and be in
control of the vehicle at all times.

The LDW system will operate when the ve-
hicle is driven at speeds of approximately
37 mph (60 km/h) and above, and only
when the lane markings are clearly visible
on the road.

The LDW system monitors the lane mark-
ers on the traveling lane using the camera
unit

O

A

located above the inside mirror.

The LDW system warns the driver with an
indicator in the vehicle information display
and a steering vibration that the vehicle is
beginning to leave the driving lane. For ad-
ditional information, see “LDW system op-
eration” (P. 5-26).

LSD2839

LANE DEPARTURE WARNING (LDW)

Starting and driving

5-25

-------------------------------------------------------------------------------------------------------------------------------------------------------------

LDW SYSTEM OPERATION

The LDW system provides a lane departure
warning function when the vehicle is driven
at speeds of approximately 37 mph (60
km/h) and above and the lane markings
are clear. When the vehicle approaches ei-
ther the left or the right side of the traveling
lane, the steering wheel will vibrate and the
LDW indicator in the vehicle information
display will blink to alert the driver.

The warning function will stop when the
vehicle returns inside of the lane markers.

LSD3646

5-26

Starting and driving

-------------------------------------------------------------------------------------------------------------------------------------------------------------

HOW TO ENABLE/DISABLE THE
LDW SYSTEM

Perform the following steps to enable or
disable the LDW system:

1. Press the

button until “Settings” dis-

plays in the vehicle information display.
Use the

button to select “Driver As-

sistance.” Then press the OK button.

2. Select “Lane” and press the OK button.

3. Select “Lane Departure Warning” and

use the OK button to turn the system on
or off.

LDW SYSTEM LIMITATIONS

WARNING

Listed below are the system limitations
for the LDW system. Failure to follow
the

warnings

and

instructions

for

proper use of the LDW system could re-
sult in serious injury or death.

The system will not operate at
speeds below approximately 37 mph
(60 km/h) or if it cannot detect lane
markers.

Do not use the LDW system under the
following conditions as it may not
function properly:

During bad weather (rain, fog,

snow, etc.).

LSD3647

Starting and driving

5-27

-------------------------------------------------------------------------------------------------------------------------------------------------------------

When driving on slippery roads,

such as on ice or snow.

When driving on winding or un-

even roads.

When there is a lane closure due to

road repairs.

When driving in a makeshift or

temporary lane.

When driving on roads where the

lane width is too narrow.

When driving without normal tire

conditions (for example, tire wear,
low tire pressure, installation of
spare tire, tire chains, nonstan-
dard wheels).

When the vehicle is equipped with

non-original brake parts or sus-
pension parts.

The system may not function prop-
erly under the following conditions:

On roads where there are multiple

parallel lane markers; lane mark-
ers that are faded or not painted
clearly; yellow painted lane mark-
ers; non-standard lane markers;
or lane markers covered with wa-
ter, dirt, snow, etc.

On roads where the discontinued

lane markers are still detectable.

On roads where there are sharp

curves.

On roads where there are sharply

contrasting objects, such as shad-
ows, snow, water, wheel ruts,
seams or lines remaining after
road repairs. (The LDW system
could detect these items as lane
markers.)

On roads where the traveling lane

merges or separates.

When the vehicle’s traveling direc-

tion does not align with the lane
marker.

When traveling close to the ve-

hicle in front of you, which ob-
structs the lane camera unit de-
tection range.

When rain, snow, dirt or an object

adheres to the windshield in front
of the lane camera unit.

When

the

headlights

are

not

bright due to dirt on the lens or if
the

aiming

is

not

adjusted

properly.

When strong light enters the lane

camera unit (for example, the light
directly shines on the front of the
vehicle at sunrise or sunset).

When a sudden change in bright-

ness occurs (for example, when
the vehicle enters or exits a tunnel
or under a bridge).

SYSTEM TEMPORARILY
UNAVAILABLE

If the vehicle is parked in direct sunlight
under high temperature conditions (over
approximately

104°F

[40°C])

and

then

started, the LDW system may be deacti-
vated automatically and the following
message will appear in the vehicle infor-
mation display: “Unavailable: High Cabin
Temperature.”

When the interior temperature is reduced,
the LDW system will resume operating
automatically

The LDW system is not designed to warn
under the following conditions:
• When you operate the lane change signal

and change traveling lanes in the direc-
tion of the signal. (The LDW system will
become operable again approximately 2
seconds after the lane change signal is
turned off.)

• When the vehicle speed lowers to less

than approximately 37 mph (60 km/h).

5-28

Starting and driving

-------------------------------------------------------------------------------------------------------------------------------------------------------------

After the above conditions have finished
and the necessary operating conditions
are satisfied, the LDW functions will resume.

SYSTEM MALFUNCTION

If the LDW system malfunctions, it will can-
cel automatically and “Malfunction: See
Owner’s Manual” will appear in the vehicle
information display. If “Malfunction: See
Owner’s Manual” appears in the vehicle in-
formation display, pull off the road to a safe
location and stop the vehicle. Push the P
(Park) position switch on the shift lever and
the power switch in the OFF position and
restart the EV system. If “Malfunction: See
Owner’s Manual” continues to appear in
the vehicle information display, have the
system checked. It is recommended that
you visit a NISSAN certified LEAF dealer for
this service.

SYSTEM MAINTENANCE

The lane camera unit

O

1

for the LDW sys-

tem is located above the inside mirror. To
keep the proper operation of the LDW sys-
tem and prevent a system malfunction, be
sure to observe the following:
• Always keep the windshield clean.
• Do not attach a sticker (including trans-

parent material) or install an accessory
near the camera unit.

• Do not place reflective materials, such as

white paper or a mirror, on the instru-
ment panel. The reflection of sunlight
may adversely affect the camera unit’s
capability of detecting the lane markers.

• Do not strike or damage the areas

around the camera unit. Do not touch the
camera lens or remove the screw located
on the camera unit. If the camera unit is
damaged due to an accident, it is recom-
mended that you visit a NISSAN certified
LEAF dealer.

LSD2847

Starting and driving

5-29

-------------------------------------------------------------------------------------------------------------------------------------------------------------

WARNING

Failure to follow the warnings and in-
structions for proper use of the I-LI sys-
tem could result in serious injury or
death.

The I-LI system will not steer the ve-
hicle or prevent loss of control. It is
the driver’s responsibility to stay
alert, drive safely, keep the vehicle in
the traveling lane, and be in control of
the vehicle at all times.

The I-LI system is primarily intended
for use on well-developed freeways
or highways. It may not detect the
lane

markers

in

certain

road,

weather, or driving conditions.

The I-LI system must be turned on with the
ProPILOT Assist switch on the steering
wheel (models with ProPILOT Assist) or the
dynamic driver assistance switch (models
without ProPILOT Assist) every time the
power switch is placed in the ON position.

The I-LI system will operate when the ve-
hicle is driven at speeds of approximately
37 mph (60 km/h) and above, and only
when the lane markings are clearly visible
on the road.

The I-LI system warns the driver when the
vehicle has left the center of the traveling
lane with an indicator in the vehicle infor-
mation display and a steering vibration.
The system helps assist the driver to return
the vehicle to the center of the traveling
lane by applying the brakes to the left or
right wheels individually (for a short period
of time).

The I-LI system monitors the lane markers
on the traveling lane using the camera unit

O

A

located above the inside mirror.

LSD2839

INTELLIGENT LANE INTERVENTION
(I-LI)

5-30

Starting and driving

-------------------------------------------------------------------------------------------------------------------------------------------------------------

I-LI SYSTEM OPERATION

1. Lane Departure Warning (LDW) indicator

2. Intelligent

Lane

Intervention

(I-LI)

indicator

3. ProPILOT Assist switch (for models with

ProPILOT Assist)

4. Dynamic driver assistance switch (for

models without ProPILOT Assist)

The I-LI system operates above approxi-
mately 37 mph (60 km/h). When the vehicle
approaches either the left or the right side
of the traveling lane, the steering wheel will
vibrate and the LDW indicator in the vehicle
information display will blink to alert the
driver. Then, the I-LI system will automati-
cally apply the brakes for a short period of
time to help assist the driver to return the
vehicle to the center of the traveling lane.

To turn on the I-LI system, push the ProPI-
LOT Assist switch on the steering wheel
(models with ProPILOT Assist) or dynamic
driver assistance switch (models without
ProPILOT Assist). The I-LI indicator will illu-
minate. Push the ProPILOT Assist switch
(models with ProPILOT Assist) or dynamic
driver assistance switch (models without
ProPILOT Assist) again to turn off the I-LI
system. The I-LI indicator will turn off.

LSD3648

Starting and driving

5-31

-------------------------------------------------------------------------------------------------------------------------------------------------------------

HOW TO ENABLE/DISABLE THE I-LI
SYSTEM

Perform the following steps to enable or
disable the I-LI system:

1. Press the

button until “Settings” dis-

plays in the vehicle information display.
Use the

button to select “Driver As-

sistance.” Then press the OK button.

2. Select “Lane” and press the OK button.

3. Select “Lane Departure Prevention” and

press the OK button.

4. Push the ProPILOT Assist switch (mod-

els with ProPILOT Assist) or dynamic
driver assistance switch (models with-
out ProPILOT Assist) to turn the system
on or off.

NOTE:

When Lane Departure Prevention is ON in
the settings menu, turning the ProPILOT
Assist system (if so equipped) on will ac-
tivate the Intelligent Lane Intervention
(I-LI) system at the same time. If Lane
Departure Prevention is OFF in the set-
tings menu, I-LI will automatically acti-
vate when ProPILOT Assist is “SET” or
Steering Assist is active. For additional
information, see “Intelligent Lane Inter-
vention (I-LI)” (P. 5-30).

LSD3647

5-32

Starting and driving

-------------------------------------------------------------------------------------------------------------------------------------------------------------

I-LI SYSTEM LIMITATIONS

WARNING

Listed below are the system limitations
for the I-LI system. Failure to follow the
warnings and instructions for proper
use of the I-LI system could result in
serious injury or death.

The I-LI system may activate if you
change lanes without first activating
your turn signal or, for example, if a
construction zone directs traffic to
cross an existing lane marker. If this
occurs you may need to apply correc-
tive steering to complete your lane
change.

Because the I-LI may not activate un-
der the road, weather, and lane
marker conditions described in this
section, it may not activate every
time your vehicle begins to leave its
lane and you will need to apply cor-
rective steering.

When the I-LI system is operating,
avoid excessive or sudden steering
maneuvers. Otherwise, you could
lose control of the vehicle.

The I-LI system will not operate at
speeds below approximately 37 mph
(60 km/h) or if it cannot detect lane
markers.

Do not use the I-LI system under the
following conditions as it may not
function properly:

During bad weather (rain, fog,

snow, etc.).

When driving on slippery roads,

such as on ice or snow.

When driving on winding or un-

even roads.

When there is a lane closure due to

road repairs.

When driving in a makeshift or

temporary lane.

When driving on roads where the

lane width is too narrow.

When driving without normal tire

conditions (for example, tire wear,
low tire pressure, installation of
spare tire, tire chains, nonstan-
dard wheels).

When the vehicle is equipped with

nonoriginal brake parts or sus-
pension parts.

On roads where there are multiple

parallel lane markers; lane mark-
ers that are faded or not painted
clearly; yellow painted lane mark-
ers; non-standard lane markers;
or lane markers covered with wa-
ter, dirt, snow, etc.

On roads where discontinued lane

markers are still detectable.

On roads where there are sharp

curves.

On roads where there are sharply

contrasting objects, such as shad-
ows, snow, water, wheel ruts,
seams or lines remaining after
road repairs. (The I-LI system
could detect these items as lane
markers.)

On roads where the traveling lane

merges or separates.

When the vehicle’s traveling direc-

tion does not align with the lane
marker.

When traveling close to the ve-

hicle in front of you, which ob-
structs the lane camera unit de-
tection range.

Starting and driving

5-33

-------------------------------------------------------------------------------------------------------------------------------------------------------------

When rain, snow or dirt adheres to

the windshield in front of the lane
camera unit.

When

the

headlights

are

not

bright due to dirt on the lens or if
the

aiming

is

not

adjusted

properly.

When strong light enters the lane

camera unit (for example, the light
directly shines on the front of the
vehicle at sunrise or sunset).

When a sudden change in bright-

ness occurs (for example, when
the vehicle enters or exits a tunnel
or under a bridge).

While the I-LI system is operating, you may
hear a sound of brake operation. This is
normal and indicates that the I-LI system is
operating proper ly.

SYSTEM TEMPORARILY
UNAVAILABLE

Condition A:

The warning and assist functions of the I-LI
system are not designed to work under the
following conditions:
• When you operate the lane change signal

and change the traveling lanes in the di-
rection of the signal. (The I-LI system will
be deactivated for approximately 2 sec-
onds after the lane change signal is
turned off.)

• When the vehicle speed lowers to less

than approximately 37 mph (60 km/h).

After the above conditions have finished
and the necessary operating conditions
are satisfied, the warning and assist func-
tions will resume.

Condition B:

The assist function of the I-LI system is not
designed to work under the following con-
ditions (warning is still functional):
• When the brake pedal is depressed.
• When the steering wheel is turned as far

as necessary for the vehicle to change
lanes.

• When the vehicle is accelerated during

I-LI system operation.

• When the Intelligent Cruise Control (ICC)

approach warning occurs.

• When the hazard warning flashers are

operated.

• When driving on a curve at high speed.

After the above conditions have finished
and the necessary operating conditions
are satisfied, the I-LI system application of
the brakes will resume.

Condition C:

If the following messages appear in the
vehicle information display, a chime will
sound and the I-LI system will be turned off
automatically.
• “Not Available - Poor Road Conditions”:

When the Vehicle Dynamic Control (VDC)
system (except Traction Control System
[TCS] function) or ABS operates.

• “Currently not available”: When the VDC

system is turned off.

Action to take:

When the above conditions no longer exist,
turn off the I-LI system. Push the ProPILOT
Assist switch (models with ProPILOT Assist)
or dynamic driver assistance switch (mod-
els without ProPILOT Assist) to turn the I-LI
system back on.

5-34

Starting and driving

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Temporary

disabled

status

at

high

temperature:

If the vehicle is parked in direct sunlight
under high temperature conditions (over
approximately 104°F [40°C]) and then the
I-LI system is turned on, the I-LI system
may be deactivated automatically and the
following message will appear on the ve-
hicle information display: “Unavailable: High
Cabin Temperature.” When the interior
temperature is reduced, the system will re-
sume operating automatically.

SYSTEM MALFUNCTION

If the I-LI system malfunctions, it will cancel
automatically. The I-LI indicator (orange)
will illuminate and “Malfunction: See Own-
er’s Manual” warning message will appear
in the display.

If the I-LI indicator (orange) illuminates in
the display, pull off the road to a safe loca-
tion and stop the vehicle. Turn the EV sys-
tem off and restart the EV system. If the I-LI
indicator (orange) continues to illuminate,
have the I-LI system checked. It is recom-
mended that you visit a NISSAN certified
LEAF dealer for this service.

SYSTEM MAINTENANCE

The lane camera unit

O

1

for the I-LI system

is located above the inside mirror. To keep
the proper operation of the I-LI system and
prevent a system malfunction, be sure to
observe the following:
• Always keep the windshield clean.
• Do not attach a sticker (including trans-

parent material) or install an accessory
near the camera unit.

• Do not place reflective materials, such as

white paper or a mirror, on the instru-
ment panel. The reflection of sunlight
may adversely affect the camera unit’s
capability of detecting the lane markers.

• Do not strike or damage the areas

around the camera unit. Do not touch the
camera lens or remove the screw located
on the camera unit. If the camera unit is
damaged due to an accident, it is recom-
mended that you visit a NISSAN certified
LEAF dealer.

LSD2847

Starting and driving

5-35

-------------------------------------------------------------------------------------------------------------------------------------------------------------

WARNING

Failure to follow the warnings and in-
structions for proper use of the BSW
system could result in serious injury or
death.

The BSW system is not a replacement
for proper driving procedures and is
not designed to prevent contact with
vehicles or objects. When changing
lanes, always use the side and rear
mirrors and turn and look in the di-
rection your vehicle will move to en-
sure it is safe to change lanes. Never
rely solely on the BSW system.

The BSW system helps alert the driver of
other vehicles in adjacent lanes when
changing lanes.

The BSW system uses radar sensors

O

1

installed near the rear bumper to detect
other vehicles in an adjacent lane.

The radar sensors can detect vehicles on
either side of your vehicle within the detec-
tion zone shown as illustrated. This detec-
tion zone starts from the outside mirror of
your vehicle and extends approximately
10 ft (3.0 m) behind the rear bumper, and
approximately 10 ft (3.0 m) sideways.

LSD3768

LSD2875

Detection zone

BLIND SPOT WARNING (BSW)

5-36

Starting and driving

-------------------------------------------------------------------------------------------------------------------------------------------------------------

BSW SYSTEM OPERATION

1. Side Indicator Light

2. BSW Indicator

The BSW system operates above approxi-
mately 20 mph (32 km/h).

If the radar sensors detect a vehicle in the
detection zone, the side indicator light (1)
illuminates. If the turn signal is then acti-
vated, the system chimes (twice), the side
indicator light flashes, and the BSW indica-
tor (2) illuminates (yellow) in the vehicle in-
formation display. The side indicator light
continues to flash until the detected ve-
hicle leaves the detection zone.

The side indicator light illuminates for a few
seconds when the power switch is placed
in the ON position.

If a vehicle comes into the detection zone
after the driver activates the turn signal,
then only the side indicator light flashes
and no chime sounds. For additional infor-
mation,

see

“BSW

driving

situations”

(P. 5-40).

The BSW system automatically turns on
every time the EV system is started, as long
as it is activated using the settings menu
on the vehicle information display.

LSD4767

Starting and driving

5-37

-------------------------------------------------------------------------------------------------------------------------------------------------------------

HOW TO ENABLE/DISABLE THE
BSW S
YSTEM

Perform the following steps to enable or
disable the BSW system:

1. Press the

button until “Settings” dis-

plays in the vehicle information display.
Use the

button to select “Driver As-

sistance.” Then press the OK button.

2. Select “Blind Spot” and press the OK

button.

3. Select “Blind Spot Warning” and use the

OK button to turn the system on or off.

NOTE:

When enabling/disabling the system,
the system will retain current settings
even if the EV system is restarted.

LSD3651

5-38

Starting and driving

-------------------------------------------------------------------------------------------------------------------------------------------------------------

BSW SYSTEM LIMITATIONS

WARNING

Listed below are the system limitations
for the BSW system. Failure to operate
the vehicle in accordance with these
system limitations could result in seri-
ous injury or death.

The BSW system cannot detect all ve-
hicles under all conditions.

The radar sensors may not be able to
detect and activate BSW when cer-
tain objects are present such as:

Pedestrian, bicycles, animals.

Vehicles such as motorcycles, low

height vehicles, or high ground
clearance vehicles.

Oncoming vehicles.

Vehicles remaining in the detec-

tion zone when you accelerate
from a stop.

A vehicle merging into an adjacent

lane at a speed approximately the
same as your vehicle.

A

vehicle

approaching

rapidly

from behind.

A vehicle which your vehicle over-

takes rapidly.

A vehicle that passes through the

detection zone quickly.

When overtaking several vehicles

in a row, the vehicles after the first
vehicle may not be detected if
they are traveling close together.

The radar sensor’s detection zone is
designed based on a standard lane
width. When driving in a wider lane,
the radar sensors may not detect ve-
hicles in an adjacent lane. When driv-
ing in a narrow lane, the radar sen-
sors may detect vehicles driving two
lanes away.

The radar sensors are designed to ig-
nore most stationary objects; how-
ever, objects such as guardrails,
walls, foliage and parked vehicles
may occasionally be detected. This is
a normal operation condition.

The following conditions may reduce
the ability of the radar to detect other
vehicles:

Severe weather

Road spray

Ice/frost/dirt/snow build-up on

the vehicle

Do not attach stickers (including
transparent material), install acces-
sories or apply additional paint near
the radar sensors. These conditions
may reduce the ability of the radar to
detect other vehicles.

Excessive noise (for example, audio
system volume, open vehicle win-
dow) will interfere with the chime
sound, and it may not be heard.

Starting and driving

5-39

-------------------------------------------------------------------------------------------------------------------------------------------------------------

BSW DRIVING SITUATIONS

Illustration 1:

The side indicator light illumi-

nates if a vehicle enters the detection zone
from behind in an adjacent lane.

Indicator on

Indicator off

Indicator flashing

NOTE:

The radar sensors may not detect ve-
hicles which are approaching rapidly
from behind.

Another vehicle approaching
from behind

Illustration 2:

If the driver activates the

turn signal when another vehicle is in the
detection zone, then the system chimes
(twice) and the side indicator light flashes.

LSD2877

Illustration 1 – Approaching from behind

LSD2878

Illustration 2 – Approaching from

behind

5-40

Starting and driving

-------------------------------------------------------------------------------------------------------------------------------------------------------------

 

 

 

 

 

 

 

Content      ..     20      21      22      23     ..