Nissan Rogue (2023 year). Manual in english - page 22

 

  Index      Manuals     Nissan Rogue (2023 year). Manual in english

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

 

 

 

Content      ..     20      21      22      23     ..

 

 

 

Nissan Rogue (2023 year). Manual in english - page 22

 

 

This section contains the information
about the following system features:

.

ProPILOT Assist (general system op-
eration)

.

ProPILOT Assist with Navi-link (addi-
tional functionality, if so equipped)

WARNING

Failure to follow the warnings and
instructions for proper use of the
ProPILOT Assist system could result
in serious injury or death.

.

ProPILOT Assist is not a self-driv-
ing system. Within the limits of its
capabilities, as described in this
manual, it helps the driver with
certain driving activities.

.

The ProPILOT Assist system is not
a replacement for proper driving
procedures and is not designed
to correct careless, inattentive or
absent-minded driving. ProPILOT
Assist will not always steer the
vehicle to keep it in the lane. The
ProPILOT Assist system is not
designed to prevent loss of con-
trol. It is the driver’s responsibility
to stay alert, drive safely, keep
the vehicle in the traveling lane,
and be in control of the vehicle at

all times.

.

There are limitations to the Pro-
PILOT Assist system capability.
The ProPILOT Assist system does
not function in all driving, traffic,
weather, and road conditions. It is
the driver’s responsibility to stay
alert, drive safely, keep the vehi-
cle in the traveling lane, and be in
control of the vehicle at all times.

.

The ProPILOT Assist system is
only an aid to assist the driver
and is not a collision warning or
avoidance device.

.

The ProPILOT Assist system is for
highway use only and is not
intended for city driving. Failure
to apply the brakes or steer the
vehicle when necessary may re-
sult in a serious accident.

.

Always observe posted speed
limits and do not set the speed
over them.

.

Never take your hands off the
steering wheel when driving. Al-
ways keep your hands on the
steering wheel and drive your
vehicle safely.

.

Never unfasten your safety belt
when using ProPILOT Assist.
Doing so automatically cancels

the ProPILOT Assist system.

.

The ProPILOT Assist system does
not react when approaching sta-
tionary and slow moving vehicles.

.

Always drive carefully and atten-
tively when using the ProPILOT
Assist system. Read and under-
stand the Owner’s Manual thor-
oughly before using the ProPILOT
Assist system. To avoid serious
injury or death, do not rely on the
system to prevent accidents or to
control the vehicle’s speed in
emergency situations. Do not
use the ProPILOT Assist system
except in appropriate road and
traffic conditions.

Starting and driving

5-87

PROPILOT ASSIST (if so equipped)

-------------------------------------------------------------------------------------------------------------------------------------------------------------

5-88

Starting and driving

WAF0644X

The ProPILOT Assist system is intended to
enhance the operation of the vehicle
when following a vehicle traveling in the
same lane and direction.

The ProPILOT Assist system uses a multi-
sensing front camera

installed behind

the windshield to monitor the lane mar-
kers and a radar sensor

located on the

front of the vehicle to measure the
distance to the vehicle ahead in the same
lane. If the system detects a slower
moving vehicle ahead, the system will
reduce the vehicle speed so that your
vehicle follows the vehicle in front at the
selected distance. The system will also
help keep the vehicle centered in the
traveling lane when clear lane markings

are detected.

NOTE:

It is important to ensure the front
camera and radar sensors are clear at
all times. (See “ICC sensor maintenance”
(P.5-113) and “Steering Assist mainte-
nance” (P.5-120) for more details.)

-------------------------------------------------------------------------------------------------------------------------------------------------------------

WAF0557X

Steering-wheel-mounted control (left)

Vehicle information display

Steering-wheel-mounted control (right)

ProPILOT Assist switch

Steering Assist switch

PROPILOT ASSIST SYSTEM OPERA-
TION

The ProPILOT Assist system has the
following two functions:

1. Intelligent Cruise Control (ICC)

The ICC system can be set to one of two
cruise control modes:

.

Conventional (fixed speed) cruise con-
trol mode:
For cruising at a preset vehicle speed

For additional information, see “Turning
the conventional (fixed speed) cruise
control mode ON” (P.5-94).

NOTE:

Steering Assist is not available in the
conventional (fixed speed) cruise con-
trol mode.

.

Vehicle-to-vehicle distance control
mode:
The ICC system maintains a selected
distance from the vehicle in front of
you within the speed range of 0 to 90
MPH (0 to 144 km/h) up to the vehicle
set speed. The vehicle set speed can
be selected by the driver between 20
to 90 MPH (30 to 144 km/h). When the
vehicle ahead slows to a stop, your
vehicle gradually decelerates to a
standstill. When the vehicle is stopped,
the ICC system maintains braking

Starting and driving

5-89

-------------------------------------------------------------------------------------------------------------------------------------------------------------

5-90

Starting and driving

force to keep your vehicle stopped.

.

When your vehicle is stopped for less
than approximately 3 seconds and the
vehicle ahead begins to move, your
vehicle will start moving again auto-
matically.

.

When your vehicle is at a standstill for
more than approximately 3 seconds
and the vehicle ahead begins to
accelerate, push up the CANCEL
switch to RES+ or lightly depress the
accelerator pedal. The ICC system
starts to follow the vehicle ahead.

.

Always check surroundings before
restarting the vehicle.

.

For vehicles equipped with ProPILOT
Assist with Navi-link and only when on
a limited access freeway (as identified
in the navigation map data):
— The time the vehicle can remain

stopped and automatically restart
is extended from 3 seconds to 30
seconds.

— If a vehicle ahead cuts in or out of

the lane ahead, the vehicle may not
automatically start when the traffic
ahead begins to move. You need to
push up the CANCEL switch to RES+
or lightly depress the accelerator
pedal to follow the vehicle directly
ahead when it is safe to do so.

.

When no vehicle is detected ahead
within the driver selected distance, the
vehicle travels at the speed set by the
driver. The speed must be above 20
MPH (30 km/h) to use this function.

NOTE:

Even if the Automatic Emergency Brak-
ing (AEB) setting is turned off by the
driver using the “Settings” menu in the
vehicle information display, AEB will be
automatically turned on when ICC is
used.

2. Steering Assist

The Steering Assist function helps the
driver to keep the vehicle centered within
the traveling lane.

When there is no vehicle ahead, Steering
Assist is not available at speeds under 37
MPH (60 km/h).

-------------------------------------------------------------------------------------------------------------------------------------------------------------

WAF0422X

PROPILOT ASSIST SWITCHES

1.

RES+ operation:

Resumes vehicle set speed or in-
creases speed incrementally

2.

SET- operation:

Sets desired cruise speed or reduces
speed incrementally

3. CANCEL switch:

Deactivates the ProPILOT Assist sys-
tem

4. ProPILOT Assist switch:

Turns the ProPILOT Assist system on
or off

5. DISTANCE switch:

.

Long

.

Middle

.

Short

6. Steering Assist switch:

Turns the Steering Assist function on
or off

NOTE:

For ProPILOT Assist with Navi-link
equipped vehicles: When Manual mode
is selected in the “Spd. Limit Assist”
menu, operating the CANCEL switch to
RES+ or SET- can apply the indicated
speed limit to the vehicle set speed.
(See “Speed Limit Assist - a feature of

ProPILOT Assist with Navi-link” (P.5-
105).)

Starting and driving

5-91

-------------------------------------------------------------------------------------------------------------------------------------------------------------

5-92

Starting and driving

WAF0577X

Models with full-screen display

WAF0578X

Models with analog meter and color display

PROPILOT ASSIST SYSTEM DISPLAY
AND INDICATORS

1.

ProPILOT Assist activation

Displays once the ProPILOT Assist
system is activated

2.

Vehicle ahead detection indicator

Indicates whether the system detects
a vehicle in front of you

3.

Steering Assist indicator

Indicates the status of the Steering
Assist function by the color of the
indicator

.

Steering Assist indicator (gray):

Steering Assist standby

.

Steering Assist indicator (green):

Steering Assist active

4.

Set distance indicator

Displays the selected distance

5.

Lane marker indicator

Indicates whether the system detects
lane markers

.

No lane markers displayed: Steering

Assist is turned off

.

Lane marker indicator (gray): No

lane markers detected

.

Lane marker indicator (green): Lane

markers detected, Steering Assist is
active

-------------------------------------------------------------------------------------------------------------------------------------------------------------

.

Lane marker indicator (orange):

Lane departure is detected

6.

ProPILOT Assist status indicator

(

)

Indicates the status of the ProPILOT
Assist system by the color of the
indicator

.

ProPILOT Assist status indicator

(white): ProPILOT Assist is on but
in standby

.

ProPILOT Assist status indicator

(blue): ProPILOT Assist active

7.

Steering Assist status indicator/
warning

(

,

)

Displays the status of the Steering
Assist by the color of the indicator/
warning

.

No Steering Assist status indicator

displayed: Steering Assist is turned
off

.

Steering Assist status indicator

(gray): Steering Assist standby

.

Steering Assist status indicator

(green): Steering Assist active

.

Steering Assist status indicator (or-

ange): Steering Assist malfunction

8.

Speed control status indicator/set
distance indicator/lane marker indi-
cator

(

)

Displays the status of speed control by
the color of the indicator, and displays

the selected distance by the number
of horizontal bars shown

.

Speed control status indicator

(white): ICC standby

.

Speed control status indicator

(green): ICC (distance control mode)
is active

— Green vehicle icon displayed: Vehi-

cle detected ahead

— No vehicle icon shown: No vehicle

detected ahead (Your vehicle main-
tains the driver-selected set speed.)

.

Speed control status indicator (or-

ange): Indicates an ICC malfunction

For the lane marker indicator, see
“Steering Assist display and indicators”
(P.5-116).

9.

Vehicle set speed indicator

Indicates the vehicle set speed

10.

Vehicle set speed indicator (if so
equipped)

(

)

Indicates the vehicle set speed

11.

Road information indicator (if so
equipped)

(

,

)

Indicates the detected road informa-
tion

For additional information, see “Speed
Adjust by Route - a feature of ProPI-
LOT Assist with Navi-link” (P.5-107).

12.

Detected speed limit indicator (if so
equipped)

(

)

Indicates the currently detected
speed limit

For additional information, see “Speed
Limit Assist - a feature of ProPILOT
Assist with Navi-link” (P.5-105).

13.

Speed Limit Assist indicator (if so
equipped)

(

A

,

,

)

Indicates the Speed Limit Assist acti-
vation mode or system operation

For additional information, see “Speed
Limit Assist - a feature of ProPILOT
Assist with Navi-link” (P.5-105).

NOTE:

When the ProPILOT Assist system is
activated, the display will automatically
be switched to the ProPILOT Assist
system display. To disable this function,
turn “Transition (Cruise)” off under “Cus-
tomize Display” of the settings menu.

The ProPILOT Assist display is also shown
in the Head Up Display (HUD) (if so
equipped). (See “Head Up Display (HUD)”
(P.2-50).)

Starting and driving

5-93

-------------------------------------------------------------------------------------------------------------------------------------------------------------

5-94

Starting and driving

TURNING THE CONVENTIONAL
(fixed speed) CRUISE CONTROL
MODE ON

NOTE:

ProPILOT Assist provides no approach
warnings, automatic braking, or Steer-
ing Assist in the conventional (fixed
speed) cruise control mode.

To choose the conventional (fixed speed)
cruise control mode, push and hold the
ProPILOT Assist switch for longer than
approximately 1.5 seconds. For additional
information, see “Conventional (fixed
speed) cruise control mode” (P.5-120).

WAF0423X

Example

OPERATING PROPILOT ASSIST

1.

Push the ProPILOT Assist switch

.

This turns on the ProPILOT Assist
system.

.

The ProPILOT Assist status indica-

tor

illuminates in white.

.

A screen is displayed for a period of

time that indicates the status of the
Driving Aid functions.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

WAF1248X

Example (all enabled)

When the Driving Aids are enabled:

Zone

Driving Aid

Display

Forward

Automatic Emergency
Braking (AEB) with Pe-
destrian Detection

Outline

Intelligent Forward
Collision Warning (I-
FCW)

Lane

Lane Departure Warn-
ing (LDW)

Outline

Intelligent Lane Inter-
vention (I-LI)

Shaded

Blind
Spot

Blind Spot Warning
(BSW)

Outline

Intelligent Blind Spot
Intervention (I-BSI)

Shaded

.

When any of the “Warning” systems

are enabled, the “

” mark is

shown in each zone.

.

When any of the “Intervention” sys-

tems are enabled, the “

” mark is

shown in each zone.

.

When no system is enabled, “OFF” is

shown in each zone.

WAF0560X

To change the status of the Driving
Aids, use

or

to navigate the

settings screen. For additional infor-
mation, see “How to use the vehicle
information display” (P.2-23).

2.

Accelerate or decelerate your vehicle
to the desired speed and push down
the CANCEL switch to SET-

.

The ProPILOT Assist system begins to
automatically maintain the vehicle set
speed. The ProPILOT Assist activation
indicator

and ProPILOT Assist status

indicator

illuminate in blue. When a

vehicle ahead is detected and travel-
ing at a speed of 20 MPH (30 km/h) or
below and the CANCEL switch is

Starting and driving

5-95

-------------------------------------------------------------------------------------------------------------------------------------------------------------

5-96

Starting and driving

pushed down to SET-, the vehicle set
speed is 20 MPH (30 km/h).

NOTE:

When the I-LI and I-BSI systems are
enabled in the settings menu of the
vehicle information display, turning the
ProPILOT Assist system on will turn on
the I-LI and I-BSI systems at the same
time. If the I-LI system is disabled in the
settings menu, the I-LI system will
automatically be turned on when the
Steering Assist system is active. For
additional information, see “Intelligent
Lane Intervention (I-LI)” (P.5-52), “Intelli-
gent Lane Intervention (I-LI)” (P.5-117)
and “Intelligent Blind Spot Intervention
(I-BSI)” (P.5-66).

WAF0634X

When the CANCEL switch is pushed down
to SET- under the following conditions,
the ProPILOT Assist system cannot be set
and the vehicle set speed indicator
blinks for approximately 2 seconds:

.

When traveling below 20 MPH (30
km/h) and a vehicle ahead is not
detected

.

When the shift lever is moved out of
the D (Drive) position or into the
manual shift mode

.

When the parking brake is applied

.

When the brakes are operated by the
driver

.

When the VDC system is off. For
additional information, see “Vehicle

Dynamic Control (VDC) system” (P.5-
159).

.

When the VDC system (including the
traction control system) is activated

.

When the SNOW mode or OFF-ROAD
mode is selected (AWD models)

.

When a wheel is slipping

.

When any door is open

.

When the driver’s seat belt is not
fastened

-------------------------------------------------------------------------------------------------------------------------------------------------------------

WAF0561X

How to change the vehicle set
speed

The vehicle set speed can be adjusted.

To change to a faster cruising speed:

.

Push up and hold the CANCEL switch
to RES+

. The vehicle set speed

increases in increments of 5 MPH (5
km/h).

.

Push up, then quickly release the
CANCEL switch to RES+

. Each time

you do this, the vehicle set speed
increases by 1 MPH (1 km/h).

To change to a slower cruising speed:

.

Push down and hold the CANCEL
switch to SET-

. The vehicle set

speed decreases in increments of 5
MPH (5 km/h).

.

Push down, then quickly release the
CANCEL switch to SET-

. Each time

you do this, the vehicle set speed
decreases by 1 MPH (1 km/h).

For ProPILOT Assist with Navi-link
equipped vehicles: The vehicle set speed
can also be changed according to the
speed limit. (See “Speed Limit Assist - a
feature of ProPILOT Assist with Navi-link”
(P.5-105).)

How to momentarily accelerate or
decelerate

.

Depress the accelerator pedal when
acceleration is required. Release the
accelerator pedal to resume the pre-
viously set vehicle speed.

.

Depress the brake pedal when decel-
eration is required. Control by the
ProPILOT Assist system is canceled.
Push up the CANCEL switch to RES+ to
resume the previously set vehicle
speed.

WARNING

When the accelerator pedal is de-
pressed and you are approaching
the vehicle ahead, the ICC system

will neither control the brake nor
warn the driver with the chime and
display. The driver must manually
control the vehicle speed to maintain
a safe distance to the vehicle ahead.
Failure to do so could result in severe
personal injury or death.

NOTE:

When you accelerate by depressing the
accelerator pedal or decelerate by
pushing down the CANCEL switch to
SET- and the vehicle travels faster than
the speed set by the driver, the vehicle
set speed indicator will blink.

Starting and driving

5-97

-------------------------------------------------------------------------------------------------------------------------------------------------------------

5-98

Starting and driving

WAF0424X

How to change the set distance to
the vehicle ahead

The distance to the vehicle ahead can be
selected at any time.

Each time the DISTANCE switch

is

pushed, the set distance will change to
“long”, “middle”, “short” and back to “long”
again in that sequence.

WAF0645X

Example

Distance — approximate distance at 60
MPH (100 km/h)

1.

Long – 200 ft (60 m)

2.

Middle – 150 ft (45 m)

3.

Short – 90 ft (30 m)

.

The actual distance to the vehicle
ahead adjusts automatically accord-
ing to the vehicle speed. The higher
the vehicle speed, the longer the
distance.

.

The distance setting will remain at the
current setting even if the engine is
restarted.

HOW TO ENABLE/DISABLE THE
STEERING ASSIST

Use the following methods to enable or
disable the Steering Assist.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

WAF0425X

Steering-wheel-mounted control (left)

Vehicle information display

Steering Assist switch

Steering Assist switch:

To turn the Steering Assist on or off, push
the Steering Assist switch

on the

instrument panel.

NOTE:

.

When the Steering Assist switch is
used to turn the system on or off,
the system remembers the setting
even if the ignition switch is cycled.
The switch must be pushed again to
change the setting to on or off.

.

The Steering Assist switch changes
the status of the “Steering Assist”
selection made in the “Settings”
screen in the vehicle information
display.

Setting in the vehicle information dis-
play:

1.

Push the

button on the

steering wheel

until “Settings” ap-

pears in the vehicle information dis-
play

and then push the scroll dial.

2.

Use the scroll dial to select “Driver
Assistance.” Then push the scroll dial.

3.

Select “Steering Assist” and push the
scroll dial to turn the Steering Assist
on or off.

NOTE:

.

When the Cruise screen is displayed
on the vehicle information display,
push the scroll dial on the steering
wheel to call up the “Driver Assis-
tance” setting display.

.

When enabling/disabling the system
through the vehicle information dis-
play, the system retains the current
settings even if the engine is re-
started.

Starting and driving

5-99

-------------------------------------------------------------------------------------------------------------------------------------------------------------

5-100

Starting and driving

HOW TO CANCEL THE PROPILOT
ASSIST SYSTEM

To cancel the ProPILOT Assist system, use
one of the following methods:

.

Push the CANCEL switch.

.

Tap the brake pedal (except at a
standstill).

.

Push the ProPILOT Assist switch to
turn the system off. The ProPILOT
Assist status indicator will turn off.

When the ProPILOT Assist system is
canceled while the vehicle is stopped,
the electronic parking brake is automati-
cally activated.

WARNING

To prevent the vehicle from moving
or rolling unexpectedly, which could
result in serious personal injury or
property damage, before exiting the
vehicle make sure to push the Pro-
PILOT Assist switch to turn the sys-
tem off, push the park button to shift
to the P (Park) position, and turn the
engine off.

INTELLIGENT CRUISE CONTROL
(ICC)

.

The Intelligent Cruise Control (ICC) is a
part of the ProPILOT Assist system. To
choose the ICC system without the
Steering Assist, activate the ProPILOT
Assist and then turn off the Steering
Assist with the switch or in the set-
tings menu. For additional informa-
tion, see “Operating ProPILOT Assist”
(P.5-94) and “How to enable/disable
the Steering Assist” (P.5-98).

.

To choose the conventional (fixed
speed) cruise control mode, push and
hold the ProPILOT Assist switch for
longer than approximately 1.5 sec-
onds. For additional information, see
“Conventional (fixed speed) cruise
control mode” (P.5-120).

WARNING

Failure to follow the warnings and
instructions for proper use of the ICC
system could result in serious injury
or death.

.

The ICC system is only an aid to
assist the driver and is not a
collision warning or avoidance
device. It is recommended for
highway use only and it is not

intended for city driving. It is the
driver’s responsibility to stay
alert, drive safely, and be in con-
trol of the vehicle at all times.

.

There are limitations to the ICC
system capability. The ICC system
does not function in all driving,
traffic, weather, and road condi-
tions. It is the driver’s responsi-
bility to stay alert, drive safely,
keep the vehicle in the traveling
lane, and be in control of the
vehicle at all times.

.

Always observe posted speed
limits and do not set the speed
over them.

.

The ICC system does not react to
stationary and slow moving vehi-
cles.

.

Always drive carefully and atten-
tively when using the ICC system.
Read and understand the Owner’s
Manual thoroughly before using
the ICC system. To avoid serious
injury or death, do not rely on the
system to prevent accidents or to
control the vehicle’s speed in
emergency situations. Do not
use the ICC system except in
appropriate road and traffic con-
ditions.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

ICC system operation

The ICC system is designed to maintain a
selected distance from the vehicle in front
of you and can reduce the speed to
match a slower vehicle ahead. The sys-
tem decelerates the vehicle as necessary
and if the vehicle ahead comes to a stop,
the vehicle decelerates to a standstill.
However, the ICC system can only apply
up to 40% of the vehicle’s total braking
power.

This system should only be used when
traffic conditions allow vehicle speeds to
remain fairly constant or when vehicle
speeds change gradually. If a vehicle
moves into the traveling lane ahead or if
a vehicle traveling ahead rapidly decele-
rates, the distance between vehicles may
become closer because the ICC system
cannot decelerate the vehicle quickly
enough. If this occurs, the ICC system
sounds a warning chime and blinks the
system display to notify the driver to take
necessary action.

The ICC system cancels and a warning
chime sounds if the speed is below
approximately 15 MPH (25 km/h) and a
vehicle is not detected ahead. For ProPI-
LOT Assist with Navi-link equipped vehi-
cles on a limited access freeway as
identified in the navigation map data,
the ICC system cancels and a warning

chime sounds if your vehicle is at a
standstill for more than approximately 3
seconds and a vehicle is not detected
ahead.

The ICC system operates as follows:

.

When there are no vehicles traveling
ahead, the ICC system maintains the
speed set by the driver. The vehicle set
speed range is between approxi-
mately 20 and 90 MPH (30 and 144
km/h).

.

When there is a vehicle traveling
ahead, the ICC system adjusts the
speed to maintain the distance, se-
lected by the driver, from the vehicle
ahead. If the vehicle ahead comes to a
stop, the vehicle decelerates to a
standstill. Once your vehicle stops,
the ICC system keeps the vehicle
stopped.

.

When the vehicle traveling ahead
moves to a different traveling lane,
the ICC system accelerates and main-
tains vehicle speed up to the set
speed.

The ICC system does not control vehicle
speed or warn you when you approach
stationary and slow moving vehicles. You
must pay attention to vehicle operation
to maintain proper distance from vehicles
ahead when approaching toll gates or
traffic congestion.

SSD0254

When driving on the highway at a vehicle
set speed and approaching a slower
traveling vehicle ahead, the ICC system
adjusts the speed to maintain the dis-
tance, selected by the driver, from the
vehicle ahead. If the vehicle ahead
changes lanes or exits the highway, the
ICC system accelerates and maintains the
vehicle set speed. Pay attention to the
driving operation to maintain control of
the vehicle as it accelerates to the set
speed.

The vehicle may not maintain the set
speed on winding or hilly roads. If this
occurs, you will have to manually control
the vehicle speed.

Starting and driving

5-101

-------------------------------------------------------------------------------------------------------------------------------------------------------------

5-102

Starting and driving

Normally when controlling the distance to
a vehicle ahead, the system automatically
accelerates or decelerates your vehicle
according to the speed of the vehicle
ahead.

Depress the accelerator to properly ac-
celerate your vehicle when acceleration is
required for a lane change. Depress the
brake pedal when deceleration is required
to maintain a safe distance to the vehicle
ahead due to sudden braking or if a
vehicle cuts in. Always stay alert when
using the ICC system.

WAF0579X

System set display — no vehicle detected ahead*

No vehicle detected ahead:

The driver sets the desired vehicle speed
based on the road conditions. The ICC
system maintains the vehicle set speed,
similar to standard cruise control, as long
as no vehicle is detected in the lane
ahead. The ICC system displays the vehi-
cle set speed.

*: The design of the set display may differ
depending on the model.

WAF0580X

System set display — vehicle ahead*

Vehicle detected ahead:

When a vehicle is detected in the lane
ahead, the ICC system decelerates the
vehicle by controlling the throttle and
applying the brakes to match the speed
of a slower vehicle ahead. The ICC system
then adjusts the vehicle speed based on
the speed of the vehicle ahead to main-
tain the driver selected distance.

NOTE:

.

The stop lights of the vehicle come
on when braking is performed by
the ICC system.

.

When the brake is applied by the
system, a noise may be heard. This is
not a malfunction.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

 

 

 

 

 

 

 

Content      ..     20      21      22      23     ..