Nissan Rogue (2023 year). Manual in english - page 18

 

  Index      Manuals     Nissan Rogue (2023 year). Manual in english

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

 

 

 

Content      ..     16      17      18      19     ..

 

 

 

Nissan Rogue (2023 year). Manual in english - page 18

 

 

this function, depress the brake
pedal to stop the vehicle because
the shift lever is in the N (Neutral)
position.

.

If this function is not activated
regardless of proper operation,
transmission may malfunction. It
is recommended that you visit a
NISSAN dealer for this service.

To activate the Neutral hold mode, per-
form the following operations.

1.

Push the ignition switch to start the
engine.

2.

Release the electronic parking brake.

3. Depress and hold the brake pedal.

4. Push the P position switch.

5. Slide the shift lever to the N (Neutral)

position, and hold it for approximately
0.5 seconds until “N” appears in the
vehicle information display.

6. Slide the shift lever to the N (Neutral)

position again, and hold it for approxi-
mately 0.5 seconds, until a message
“Neutral Hold Mode has been acti-
vated” appears in the vehicle informa-
tion display. (See “66. Neutral Hold
Mode activated indicator” (P.2-44).)

7.

Place the ignition switch in the OFF
position. The engine will turn off with

holding the N (Neutral) position.

To exit the Neutral hold mode, place the
vehicle in other than N (Neutral) position.

NOTE:

.

It is necessary to perform the steps
4 through 6 within approximately 5
seconds to prevent incorrect opera-
tion.

.

When the ignition switch is placed in
the OFF position while the shift lever
is in the N (Neutral) position, a
message will appear in the vehicle
information display. (See “65. Neu-
tral Hold Mode guidance indicator”
(P.2-44).)

.

If the Neutral hold mode is unavail-
able, a message will appear in the
vehicle information display. (See “67.
Neutral Hold Mode was not activated
indicator” (P.2-44).) To activate the
Neutral hold mode, wait for a while
without shifting operation and then
perform the operations again.

WAF0417X

Paddle shifter

Manual shift mode

When the shift lever is moved to the D
(Drive) position again with the vehicle in
the D (Drive) position while driving, the
transmission enters the manual shift
mode. Shift range can be selected manu-
ally using the paddle shifters on the
steering wheel.

When shifting up, pull the right-side
paddle shifter (+)

. The transmission

shifts to the higher range.

When shifting down, pull the left-side
paddle shifter (−)

. The transmission

shifts to the lower range.

When canceling the manual shift mode,

Starting and driving

5-23

-------------------------------------------------------------------------------------------------------------------------------------------------------------

5-24

Starting and driving

move the shift lever to the D (Drive)
position again. The transmission returns
to the normal driving mode.

When you pull the paddle shifter while in
the D (Drive) position, the transmission
will shift to the upper or lower range
temporarily. The transmission will auto-
matically return to the D (Drive) position
after a short period of time. If you want to
return to the D (Drive) position manually,
pull and hold the paddle shifter for about
1.5 seconds.

In the manual shift mode, the shift range
is displayed in the vehicle information
display.

Shift ranges up or down one by one as
follows:

1

M

?

/

2

M

?

/

3

M

?

/

4

M

?

/

5

M

?

/

6

M

?

/

7

M

?

/

8

M

8

M

(8th):

Use this position for all normal forward
driving at highway speeds.

7

M

(7th), 6

M

(6th) and 5

M

(5th):

Use these positions when driving up long
slopes, or for engine braking when driving
down long slopes.

4

M

(4th), 3

M

(3rd) and 2

M

(2nd):

Use these positions for hill climbing or
engine braking on downhill grades.

1

M

(1st):

Use this position when climbing steep
hills slowly or driving slowly through deep
snow, or for maximum engine braking on
steep downhill grades.

.

Remember not to drive at high speeds
for extended periods of time in lower
than 8th gear. This reduces fuel econ-
omy.

.

Pulling the same paddle shifter twice
will shift the ranges in succession.
However, if this motion is rapidly done,
the second shifting may not be com-
pleted properly.

.

In the manual shift mode, the trans-
mission may not shift to the se-
lected gear. This helps maintain
driving performance and reduces
the chance of vehicle damage or
loss of control.

.

When this situation occurs, the Con-
tinuously Variable Transmission
(CVT) position indicator will blink
and the chime will sound.

.

In the manual shift mode, the trans-
mission may shift up automatically
to a higher range than selected if the
engine speed is too high. When the
vehicle speed decreases, the trans-
mission automatically shifts down
and shifts to 1st gear before the
vehicle comes to a stop.

.

CVT operation is limited to automatic
drive mode when CVT fluid tempera-
ture is extremely low even if manual
shift mode is selected. This is not a
malfunction. When CVT fluid warms
up, manual shift mode can be se-
lected.

.

When the CVT fluid temperature is
high, the shift range may upshift in
lower rpm than usual. This is not a
malfunction.

Accelerator downshift - in D (Drive)
position -

For passing or climbing hills, depress the
accelerator pedal to the floor. This shifts
the transmission down into a lower gear,
depending on the vehicle speed.

High fluid temperature protection
mode

This transmission has a high fluid tem-
perature protection mode. If the fluid
temperature becomes too high, (for ex-
ample, when climbing steep grades in
high temperatures with heavy loads, such
as when towing a trailer), engine power
and, under some conditions, vehicle
speed will be decreased automatically to
reduce the chance of transmission da-
mage. Vehicle speed can be controlled
with the accelerator pedal, but the engine

-------------------------------------------------------------------------------------------------------------------------------------------------------------

and vehicle speed may be limited.

Fail-safe

When the fail-safe operation occurs, the
Continuously Variable Transmission will
not be shifted into the selected driving
position.

If the vehicle is driven under extreme
conditions, such as excessive wheel
spinning and subsequent hard braking,
the fail-safe system may be activated.
The Malfunction Indicator Light (MIL)
may come on to indicate the fail-safe
mode is activated. For additional infor-
mation, refer to “Malfunction Indicator
Light (MIL)” (P.2-19). This will occur even
if all electrical circuits are functioning
properly. In this case, place the ignition
switch in the OFF position and wait for
10 seconds. Then place the ignition
switch back in the ON position. The
vehicle should return to its normal
operating condition. (The MIL may be
illuminated even when the vehicle has
returned to its normal operating condi-
tion.) If it does not return to its normal
operating condition, have the transmis-
sion checked and repaired, if necessary,
by a NISSAN dealer.

WARNING

When the high fluid temperature
protection mode or fail-safe opera-
tion occurs, vehicle speed may be
gradually reduced. The reduced
speed may be lower than other
traffic, which could increase the
chance of a collision. Be especially
careful when driving. If necessary,
pull to the side of the road at a safe
place and allow the transmission to
return to normal operation, or have it
repaired if necessary.

WARNING

.

Never drive the vehicle with the
parking brake applied. The brake
will overheat and fail to operate
and will lead to an accident.

.

Never release the parking brake
from outside the vehicle. If the
vehicle moves, it will be impossi-
ble to push the foot brake pedal
and will lead to an accident.

.

Never use the shift lever in place
of the parking brake. When park-
ing, be sure the parking brake is
fully applied.

.

To help avoid risk of injury or
death through unintended opera-
tion of the vehicle and/or its
systems, do not leave children,
people who require the assis-
tance of others or pets unat-
t e n d e d

i n

y o u r

v e h i c l e .

Additionally, the temperature in-
side a closed vehicle on a warm
day can quickly become high
enough to cause a significant risk
of injury or death to people and
pets.

Starting and driving

5-25

PARKING BRAKE

-------------------------------------------------------------------------------------------------------------------------------------------------------------

5-26

Starting and driving

WAF0517X

Release

Apply

Indicator light

The electronic parking brake can be
applied or released automatically or by
operating the parking brake switch.

AUTOMATIC OPERATION

The electronic parking brake is automati-
cally released as soon as the vehicle
starts while the accelerator pedal is
depressed under the following condi-
tions.

.

While the engine is running.

.

When the shift position is in the D
(Drive) or R (Reverse) position.

.

When the driver’s door is closed.

The electronic parking brake is automati-
cally released within 5 seconds after the
shift position is placed in the D (Drive) or R
(Reverse) position even if the driver’s door
is opened. Be sure to close the door
before starting the vehicle.

WARNING

.

When the automatic brake hold
function is activated, the electro-
nic parking brake will not be
automatically applied when the
engine is stopped without using
the ignition switch (for example,
by engine stalling).

Without the vehicle stationary,
the electronic parking brake will
not be automatically applied
even if the engine is turned off
with the ignition switch.

.

Before leaving the vehicle, place
the shift position in the P (Park)
position and check that the elec-
tronic parking brake warning
light is illuminated to confirm
that the electronic parking brake
is applied. The electronic parking
brake warning light will remain
on for a period of time after the

driver’s door is locked.

CAUTION

When parking in an area where the
outside temperature is below 32°F
(0°C), the electronic parking brake, if
applied, may freeze in place and may
be difficult to release.

For safe parking, it is recommended
that you place the shift position in
the P (Park) position and securely
block the wheels.

NOTE:

.

To keep the electronic parking brake
released after the engine is turned
off, place the ignition switch in the
OFF position, depress the brake
pedal and push down the parking
brake switch before opening the
driver’s door.

.

If a malfunction occurs in the elec-
tronic parking brake system (for
example, due to battery discharge),
it is recommended to contact a
NISSAN dealer.

.

Under the following conditions, the
electronic parking brake will auto-
matically be applied and the brake

-------------------------------------------------------------------------------------------------------------------------------------------------------------

force of the automatic brake hold
will be released.

The braking force is applied by
the automatic brake hold function
for 3 minutes or longer.

The vehicle is in the P (Park)
position.

The electronic parking brake is
applied manually.

The driver’s seat belt is unfas-
tened.

The driver’s door is opened.

The ignition switch is placed in
the OFF position.

A malfunction occurs in the auto-
matic brake hold function.

.

Make sure that the electronic park-
ing brake system warning light is
OFF before starting the vehicle.

MANUAL OPERATION

To apply:

When the vehicle is stopped,

pull the parking brake switch

up. (The

electronic parking brake will apply even if
the ignition switch is placed in the OFF
position.) The indicator light

on the

switch and the electronic parking brake
warning light PARK or

(red) will

illuminate.

To release:

With the ignition switch in the

ON position, depress the brake pedal and

push the parking brake switch down

.

The indicator light

and the electronic

parking brake warning light (red) will turn
off.

Before driving, check that the electronic
parking brake warning light (red) turns
off. For additional information, see “Warn-
ing lights, indicator lights and audible
reminders” (P.2-13).

NOTE:

.

While the electronic parking brake is
applied or released, an operating
sound is heard from the lower side
of the rear seat. This is normal and
does not indicate a malfunction.

.

When the electronic parking brake is
frequently applied and released in a
short period of time, the electronic
parking brake system warning light
may blink and the electronic parking
brake may not operate in order to
prevent the electronic parking brake
system from overheating. If this
occurs, operate the parking brake
switch again after waiting approxi-
mately 1 minute.

.

If the electronic parking brake must
be applied while driving in an emer-
gency, pull up and hold the parking
brake switch. When you release the
parking brake switch, the electronic
parking brake will be released.

.

While pulling up the parking brake
switch during driving, the electronic
parking brake is applied and a chime
sounds. The electronic parking
brake warning light (red) and the
indicator light on the parking brake
switch illuminate. This does not in-
dicate a malfunction. The electronic
parking brake warning light (red)
and the indicator light on the park-
ing brake switch will turn off when
the electronic parking brake is re-
leased.

.

When pulling the parking brake
switch up with the ignition switch
in the OFF position, the indicator
light on the parking brake switch
will continue to illuminate for a short
period of time.

When towing a trailer

Depending on the weight of the vehicle
and trailer and the steepness of the slope,
there may be a tendency for the vehicle
to move backwards when starting from a
standstill. When this occurs, you can use
the parking brake switch in the same way
as a conventional lever type parking
brake.

Before starting on sloping roads when
towing a trailer, be sure to read the
following to prevent the vehicle from
moving backward unintentionally.

Starting and driving

5-27

-------------------------------------------------------------------------------------------------------------------------------------------------------------

5-28

Starting and driving

.

Release the parking brake switch as
soon as the engine is delivering en-
ough torque to the wheels.

The automatic brake hold function main-
tains the braking force without the driver
having to depress the brake pedal when
the vehicle is stopped at a traffic light or
intersection. As soon as the driver de-
presses the accelerator pedal again, the
automatic brake hold function is deacti-
vated and the braking force is released.
The operating status of the automatic
brake hold can be displayed. (See “Warn-
ing lights, indicator lights and audible
reminders” (P.2-13).)

WARNING

.

The automatic brake hold func-
tion is not designed to hold the
vehicle on a steep hill or slippery
road. Never use the automatic
brake hold function when the
vehicle is stopped on a steep hill
or slippery road. Failure to do so
may cause the vehicle to move.

.

Warnings may appear to request
that the driver retake control by
depressing the brake pedal.

.

When the automatic brake hold
function is activated but fails to
maintain the vehicle at a stand-
still, depress the brake pedal to
stop the vehicle. If the vehicle
unexpectedly moves due to out-

side conditions, the chime may
sound and warnings may appear.

.

Be sure to deactivate the auto-
matic brake hold function when
using a drive-thru car wash or
towing your vehicle.

.

Make sure the vehicle is in the P
(Park) position and apply the
electronic parking brake when
parking your vehicle, riding on or
off the vehicle, or loading or
unloading luggage. Failure to do
so could cause the vehicle to
move or roll away unexpectedly
and result in serious personal
injury or property damage.

.

If any of the following conditions
occur, the automatic brake hold
function may not function. Have
the system checked promptly. It
is recommended that you visit a
NISSAN dealer for this service.

— A warning message appears.

— The indicator light on the

automatic brake hold switch
does not illuminate when the
switch is pushed.

Failure to operate the vehicle in
accordance with these conditions
could cause the vehicle to move
or roll away unexpectedly and

AUTOMATIC BRAKE HOLD

-------------------------------------------------------------------------------------------------------------------------------------------------------------

result in serious personal injury or
property damage.

.

The automatic brake hold func-
tion will not be activated if the
slip indicator light, electronic
parking brake warning light, elec-
tronic parking brake system
warning light, or master warning
light illuminates and the Chassis
Control System Error warning
message appears.

.

To maintain the braking force to
keep the vehicle to a standstill, a
noise may be heard. This is not a
malfunction.

.

The automatic brake hold func-
tion is operated by applying suf-
ficient brake force to hold the
vehicle in its place, so there are
cases when this hold function is
maintained even if the accelera-
tor pedal is depressed. In this
situation, it is advised to depress
the brake pedal first, then to turn
off the automatic brake hold
switch. This will cancel the hold
function.

WAF0516X

HOW TO ACTIVATE/DEACTIVATE
THE AUTOMATIC BRAKE HOLD
FUNCTION

How to activate the automatic
brake hold function

1.

With the ignition switch in the ON
position, push the automatic brake
hold switch

. The indicator light on

the automatic brake hold switch
illuminates.

2.

When the automatic brake hold func-
tion goes into standby, the automatic
brake hold indicator light (white) illu-
minates.

To use the automatic brake hold function,

the following conditions need to be met.

.

The driver’s seat belt is fastened.

.

The electronic parking brake is re-
leased.

.

The vehicle is not in the P (Park)
position.

.

The vehicle is not parked on a steep
hill.

NOTE:

The automatic brake hold function re-
sets to OFF every time the ignition
switch is switched from ON to OFF.

How to deactivate the automatic
brake hold function

While the automatic brake hold function
is activated, push the automatic brake
hold switch to turn off the automatic
brake hold indicator light and deactivate
the automatic brake hold function. To
deactivate the automatic brake hold
function while the brake force has been
maintained by the automatic brake hold
function, depress the brake pedal and
push the automatic brake hold switch.

WARNING

Make sure to firmly depress and hold
the brake pedal when turning off the
automatic brake hold function while

Starting and driving

5-29

-------------------------------------------------------------------------------------------------------------------------------------------------------------

5-30

Starting and driving

the brake force is applied. When the
automatic brake hold function is
deactivated, the brake force will be
released. This could cause the vehi-
cle to move or roll away unexpect-
edly.

Failure to prevent the vehicle from
rolling may result in serious personal
injury or property damage.

HOW TO USE THE AUTOMATIC
BRAKE HOLD FUNCTION

For additional information on using the
automatic brake hold function, refer to
the instructions outlined in this section.

To maintain braking force auto-
matically

With the automatic brake hold function
activated and the automatic brake hold
indicator light (white) illuminated, depress
the braking pedal to stop the vehicle and
the indicator light (green) illuminates. The
brake force is automatically applied with-
out your foot depressed on the brake
pedal. While the brake force is maintained,
the automatic brake hold indicator light
(green) illuminates.

The automatic brake hold indicator light
(green) will not illuminate if the brake
pedal is not depressed with sufficient

force to hold the vehicle or is released
too quickly when the vehicle is stopped.

Confirm the automatic brake hold indi-
cator light (green) is illuminated before
removing your foot from the brake pedal.

To start the vehicle from a stand-
still

With the vehicle not in the P (Park) or the
N (Neutral) position, depress the accel-
erator pedal while the brake force is
maintained. The brake force will automa-
tically be released to restart the vehicle.
The automatic brake hold indicator light
(white) illuminates and the automatic
brake hold returns to standby.

Parking

When the vehicle is in the P (Park) position
with the brake force maintained by the
automatic brake hold function, the elec-
tronic parking brake will automatically be
applied and the brake force of the auto-
matic brake hold will be released. The
automatic brake hold indicator light turns
off. When the electronic parking brake is
applied with the brake force maintained
by the automatic brake hold function, the
brake force of the automatic brake hold
will be released. The automatic brake
hold indicator light turns off.

NOTE:

.

Under the following conditions, the
electronic parking brake will auto-
matically be applied and the braking
force of the automatic brake hold
will be released (the automatic
brake hold indicator light turns off):

The braking force is applied by
the automatic brake hold function
for 3 minutes or longer.

The vehicle is in the P (Park)
position.

The electronic parking brake is
applied manually.

The driver’s seat belt is unfas-
tened.

The driver’s door is opened.

The ignition switch is placed in
the OFF position.

A malfunction occurs in the auto-
matic brake hold function.

.

When the vehicle stops, but the
brake force is not automatically
applied, depress the brake pedal
firmly until the automatic brake hold
indicator light (green) illuminates.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

WAF0514X

Drive Mode Selector: 2WD models

WAF0515X

Drive Mode Selector: AWD models

WAF0540X

Vehicle information display: 2WD models

WAF0541X

Vehicle information display: AWD models

Multiple driving modes can be selected by
using the Drive Mode Selector.

2WD:

SPORT, STANDARD and ECO

To change the mode, push the Drive
Mode Selector up or down.

AWD:

OFF-ROAD, SNOW, AUTO, ECO and

SPORT

To change the mode, turn the Drive Mode
Selector right or left.

NOTE:

When the Drive Mode Selector selects a
mode, the mode may not switch im-
mediately. This is not a malfunction.

The current mode is displayed in the
vehicle information display. The mode list
will appear in the vehicle information
display and you can select the mode.

NOTE:

The mode list will be turned off in
approximately 5 seconds after the
mode is selected. (The mode list can
be turned off by pushing the scroll dial
on the steering-wheel mounted con-
trols.)

If the driving mode cannot be switched
using the Drive Mode Selector when the
ignition switch is in the ON position, have
the system checked. It is recommended
you visit a NISSAN dealer for this service.

Starting and driving

5-31

DRIVE MODE SELECTOR

-------------------------------------------------------------------------------------------------------------------------------------------------------------

5-32

Starting and driving

WARNING

Do not stare at the Drive Mode
Selector or the display while driving
so that full attention may be given to
vehicle operation.

OFF-ROAD MODE (AWD models)

Allows for easier driving or starting on a
bumpy road surface such as an uneven
dirt road or a steep uphill slope or
through sand.

CAUTION

Never drive on dry, hard surface
roads in the OFF-ROAD mode, as this
will overload the powertrain and
may cause a serious malfunction.
Additionally, this will cause prema-
ture tire wear and reduced fuel
economy.

When the OFF-ROAD mode is selected,
small tight-corner braking phenomenon
or small vibration in cornering may occur.
This is not a malfunction.

SNOW MODE (AWD models)

This mode makes it easier to start and
drive on snowy roads and frozen roads.

CAUTION

Never drive on dry, hard surface
roads in the SNOW mode, as this will
overload the powertrain and may
cause a serious malfunction. Addi-
tionally, this will cause premature
tire wear and reduced fuel economy.

When the SNOW mode is selected, small
vibration in cornering may occur. This is
not a malfunction.

STANDARD MODE (2WD models)/
AUTO MODE (AWD models)

This is the standard mode that is most
suitable for normal driving.

This mode will be selected first each time
the ignition switch is placed in the ON
position.

ECO MODE

Assists the driver’s ECO-driving. The en-
gine and transmission points are adjusted
for improved fuel economy, providing
such a driving features as smooth start-
ing or constant cruising.

NOTE:

Selecting the ECO mode will not neces-
sarily improve fuel economy as many
driving factors influence its effective-
ness.

Operation

Select the ECO mode using the Drive
Mode Selector. The ECO indicator illumi-
nates.

When the accelerator pedal is depressed
within the range of economy drive, the
ECO indicator illuminates in green. When
the accelerator pedal is depressed above
the range of economy drive, the ECO
indicator turns off.

The ECO indicator will not illuminate in
the following cases:

.

When the shift lever is in the R
(Reverse) position.

.

When the vehicle speed is below 2
MPH (3.2 km/h) or over 90 MPH (144
km/h).

-------------------------------------------------------------------------------------------------------------------------------------------------------------

.

W h en th e cru ise co nt rol ( if s o
equipped) or the Intelligent Cruise
Control (ICC) system (if so equipped)
is operated.

ECO Mode Customize

When the ECO mode of the “Cruise
Control”, “Idling Stop” (if so equipped)
and/or “Air Conditioning” in addition to
the conventional power train control is
ON, more actual fuel economy is achieved
by placing priority on fuel efficiency. It can
be set when the ECO mode is selected. To
activate or deactivate this function, see
“ECO Mode Setting” (P.2-26).

.

Cruise Control
When the setting is ON, the fuel
efficiency while cruising will be im-
proved by lowering the acceleration
target from normal (setting OFF)
mode.

.

Idling Stop (if so equipped)
When the setting is ON, the idling stop
time will be extended more than
normal mode when using the air
conditioner.

.

Air Conditioning
When the setting is ON, the fuel
efficiency will be improved by redu-
cing the performance of the air con-
ditioning system.

NOTE:

When the vehicle speed is reduced (for
example, when the vehicle is driven on
an uphill road from a flat road), it will
take more time to return to the pre-
viously set speed than normal mode.

Tire Pres ECO advice

The “Tire Pres ECO advice” is a function to
show an ECO advice message in the
vehicle information display when low tire
pressure is detected. To activate or deac-
tivate this function, see “ECO Mode
Setting” (P.2-26).

When the setting is ON, the ECO Drive
Report display shows “Check Tire Pres-
sures for Best Fuel Economy”. You can
switch the display to the Tire Pressures
display by pushing the

button on

the steering wheel.

WAF0126X

ECO Pedal Guide function

The ECO Pedal Guide display can be
selected in the vehicle information display
in the ECO mode. (See “5. ECO Pedal
Guide” (P.2-48).) Use the ECO Pedal Guide
function for improving fuel economy.

When the ECO Pedal Guide bar is in the
green range

, it indicates that the

vehicle is being driven within range of
the super economy drive.

When the ECO Pedal Guide bar is in the
light green range

, it indicates that the

vehicle is being driven within range of the
economy drive.

If the ECO Pedal Guide bar is out of the

Starting and driving

5-33

-------------------------------------------------------------------------------------------------------------------------------------------------------------

5-34

Starting and driving

green range (

and

), it indicates that

the accelerator pedal is depressed over
the range of economy drive.

The ECO Pedal Guide bar is not displayed
when:

.

The vehicle speed is less than approxi-
mately 2 MPH (4 km/h).

.

The shift lever is in the P (Park), N
(Neutral) or R (Reverse) position.

SPORT MODE

.

Adjusts the engine and transmission
points for a higher response.

.

The setting of the steering system is
adjusted to moderately increase
steering wheel effort for a sporty feel.

NOTE:

In the SPORT mode, fuel economy may
be reduced.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Each Driver Assistance system is designed to help the driver in different ways as they drive. The following Driver Assistance systems (if
so equipped) are available on this vehicle:

Category

System

Symbol

System description (See the specified page for detailed information.)

Page

Forward Driving
Aids

Automatic Emergency
Braking (AEB) with Pedes-
trian Detection

Assists the driver with a warning and/or braking operation when there is a risk
of a forward collision with the vehicle ahead in the traveling lane, or with a
pedestrian or a cyclist.

5-124

Intelligent Forward Colli-
sion Warning (I-FCW)

Helps alert the driver when there is a sudden braking of a second vehicle
traveling in front of the vehicle ahead in the same lane.

5-134

Intelligent Cruise Control
(ICC) (models with ProPI-
LOT Assist)

Intelligent Cruise Control (ICC)

.

Helps the driver maintain a selected distance from the vehicle ahead and
can reduce the speed to match a slower vehicle ahead.

.

Decelerates the vehicle to a standstill when a vehicle ahead slows to a stop.

5-100

Conventional (fixed speed) cruise control mode

.

Allows the driver to drive the vehicle at a fixed speed without keeping his/
her foot on the accelerator pedal.

5-120

Cruise control (models
without ProPILOT Assist)

Allows the driver to drive the vehicle at a fixed speed without keeping his/her
foot on the accelerator pedal. (For vehicles equipped with the ProPILOT Assist,
see “Conventional (fixed speed) cruise control mode” (P.5-120).)

5-85

Side Driving Aids
(Lane and Blind
Spot)

Lane Departure Warning
(LDW)

Warns the driver that the vehicle is about to cross a lane marker with an
indicator and a steering wheel vibration.

5-47

Intelligent Lane Interven-
tion (I-LI)

.

Warns the driver that the vehicle is about to cross a lane marker with an
indicator and a steering wheel vibration.

.

Assists the driver to return the vehicle to the center of the traveling lane.

5-52

Blind Spot Warning (BSW)

Warns the driver of a vehicle in an adjacent lane when changing lanes with an
indicator.

5-58

Intelligent Blind Spot In-
tervention (I-BSI)

.

Warns the driver of a vehicle in an adjacent lane when changing lanes.

.

Assists the driver to return the vehicle to the center of the traveling lane.

5-66

Steering Assist

Assists the driver to help keep the vehicle within the center of the traveling lane
(this system is integrated in the ProPILOT Assist).

5-115

Starting and driving

5-35

DRIVER ASSISTANCE SYSTEMS

-------------------------------------------------------------------------------------------------------------------------------------------------------------

5-36

Starting and driving

Category

System

Symbol

System description (See the specified page for detailed information.)

Page

Rear Driving Aids

Rear Cross Traffic Alert
(RCTA)

Assists the driver when backing out from a parking space by detecting other
vehicles approaching from the right or left of the vehicle.

5-78

Rear Automatic Braking
(RAB)

Assists the driver when the vehicle is backing up and approaching stationary
objects directly behind the vehicle by providing a warning and automatic
braking if needed.

5-145

Parking Aids

RearView Monitor

-

Shows a rear view of the vehicle when the shift lever is placed in the R (Reverse)
position.

4-3

Intelligent Around View®
Monitor

-

Assists the driver in parking situations by showing various views of the position
of the vehicle in a split screen format.

4-10

Moving Object Detection
(MOD)

-

Informs the driver of moving objects near the vehicle in parking situations.

4-22

Sonar system

-

Informs the driver with a visual and audible alert of stationary obstacles near the
bumpers or the vehicle sides (flanks) (if so equipped).

5-164

Rear Sonar System (RSS)

-

Informs the driver with a visual and audible alert of stationary obstacles to the
rear of the vehicle when the shift lever is in the R (Reverse) position.

5-170

ProPILOT Assist

ProPILOT Assist

Consists of Intelligent Cruise Control (ICC) and Steering Assist.

5-87

Speed Limit Assist - a fea-
ture of ProPILOT Assist
with Navi-link

Detects a change of the speed limit, indicates the detected speed limit and can
apply it to the vehicle set speed automatically or manually.

5-105

Speed Adjust by Route - a
feature of ProPILOT Assist
with Navi-link

Adjusts the vehicle speed depending on curves, junctions and exits, using road
information provided by the navigation system.

5-107

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Category

System

Symbol

System description (See the specified page for detailed information.)

Page

Other Driving
Aids

High beam assist

Switches the headlights to the low beam automatically when an oncoming
vehicle or leading vehicle appears in front of your vehicle.

2-61

Traffic Sign Recognition
(TSR)

Provides the driver with information about the most recently detected speed
limit.

5-44

Intelligent Driver Alertness
(I-DA)

Helps alert the driver when a lack of attention or driving fatigue is detected.

5-143

Hill Start Assist

-

Helps prevent the vehicle from rolling backwards in the time it takes the driver to
release the brake pedal and apply the accelerator when the vehicle is stopped
on a hill.

5-163

Starting and driving

5-37

-------------------------------------------------------------------------------------------------------------------------------------------------------------

5-38

Starting and driving

WAF0412X

Steering-wheel-mounted controls (left
side)

Vehicle information display

HOW TO ENABLE/DISABLE THE
SYSTEMS

The following systems (if so equipped)
can be enabled or disabled using the
settings menu in the vehicle information
display. Select each setting item using the
scroll dial on the steering-wheel-

mounted controls.

.

Automatic Emergency Braking (AEB)
with Pedestrian Detection

.

Intelligent Forward Collision Warning
(I-FCW)

.

Lane Departure Warning (LDW)

.

Intelligent Lane Intervention (I-LI)*

.

Blind Spot Warning (BSW)

.

Intelligent Blind Spot Intervention (I-
BSI)*

.

Steering Assist

.

Rear Cross Traffic Alert (RCTA)

.

Rear Automatic Braking (RAB)

.

Moving Object Detection (MOD)

.

Sonar system

.

Rear Sonar System (RSS)

.

Speed Limit Assist (ProPILOT Assist
with Navi-link)

.

Speed Adjust by Route (ProPILOT As-
sist with Navi-link)

.

Traffic Sign Recognition (TSR)

.

Intelligent Driver Alertness (I-DA)

*: To operate the I-LI and I-BSI systems,
you need to push the ProPILOT Assist
switch after enabling each system in the
settings menu.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

 

 

 

 

 

 

 

Content      ..     16      17      18      19     ..