Nissan Rogue (2023 year). Manual in english - page 9

 

  Index      Manuals     Nissan Rogue (2023 year). Manual in english

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

 

 

 

Content      ..     7      8      9      10     ..

 

 

 

Nissan Rogue (2023 year). Manual in english - page 9

 

 

— Intelligent Blind Spot Intervention

(I-BSI) (if so equipped)

For more details, see “Automatic Emer-
gency Braking (AEB) with Pedestrian De-
tection system” (P.5-124), “Lane Departure
Warning (LDW)” (P.5-47), “Intelligent Lane
Intervention (I-LI)” (P.5-52), “Blind Spot
Warning (BSW)” (P.5-58) or “Intelligent
Blind Spot Intervention (I-BSI)” (P.5-66).

14. ProPILOT Assist (if so equipped)

The ProPILOT Assist mode shows the
operating conditions for the following
systems:

.

Intelligent Cruise Control (ICC)

.

Steering Assist

The display will also be shown when the
ProPILOT Assist is turned on. For addi-
tional information, see “ProPILOT Assist”
(P.5-87).

15. Traffic Sign Recognition (if so
equipped)

The Traffic Sign Recognition (TSR) system
provides the driver with information
about the most recently detected speed
limit. See “Traffic Sign Recognition (TSR)”
(P.5-44) for more details.

WAC0521X

CLOCK AND OUTSIDE AIR TEM-
PERATURE

The clock

and outside air temperature

are displayed on the upper side of the

vehicle information display.

Clock

For clock adjustment, see “Clock” (P.2-27)
or the separate NissanConnect® Owner’s
Manual (if so equipped).

Outside air temperature (°F or °C)

The outside air temperature is displayed
in °F or °C in the range of −40 to 140°F (−40
to 60°C).

The outside air temperature mode in-
cludes a low temperature warning fea-
ture. If the outside air temperature is
below 27°F (−3°C), the indicator

is

displayed.

The outside temperature sensor is lo-
cated in front of the radiator. The sensor
may be affected by road or engine heat,
wind directions and other driving condi-
tions. The display may differ from the
actual outside temperature or the tem-
perature displayed on various signs, bill-
boards or media information.

Instruments and controls

2-49

-------------------------------------------------------------------------------------------------------------------------------------------------------------

2-50

Instruments and controls

WAC0417X

WAC0544X

WARNING

.

Failure to properly adjust the
brightness and position of the
displayed image may interfere
with the driver’s ability to see
through the windshield, which
could cause an accident leading
to severe injury or death.

.

Do not use the Head Up Display
(HUD) for extended periods of
time as that can cause you to
not see other vehicles, pedes-
trians or objects, which could
cause an accident leading to se-
vere injury or death.

The Head Up Display (HUD) can display
one or more of the following features (if
so equipped):

Vehicle speed

Navigation

Driving Assist

Traffic Sign

Audio

TEL/SMS

NOTE:

.

Do not place any type of liquid on or
near the projector. Doing so may
cause malfunction of the equip-
ment.

HEAD UP DISPLAY (HUD) (if so equipped)

-------------------------------------------------------------------------------------------------------------------------------------------------------------

WAC0515X

.

Do not touch any internal parts of
the projector. Doing so may cause
malfunction of the equipment.

.

To prevent scratches to the projec-
tor glass, do not place any sharp
objects on or near the projector
opening.

.

Do not place any objects on the
instrument panel which may ob-
struct the display of the HUD.

.

For cleaning, use a dry soft cloth. If
dirt, etc. cannot be removed, use a
clean, soft cloth dampened with
water and then use a clean, dry soft
cloth. Never use a rough cloth, alco-
hol, benzine, thinner or any kind of
solvent or paper towel with a che-

mical cleaning agent. They will
scratch or cause discoloration to
the projector lens.

.

Do not spray any liquid such as
water on the projector lens. Spray-
ing liquid may cause the system to
malfunction.

NOTE:

.

If you wear polarized sunglasses, the
display may be difficult to see. In-
crease the brightness of the HUD in
the vehicle information display or
remove your sunglasses.

.

Depending on weather conditions
(rain, snow, sunlight, etc.), the dis-
play may be difficult to see.

.

If the displayed image appears dis-
torted, it is recommended you have
the system checked by a NISSAN
dealer.

.

The HUD has a special windshield to
allow the image to be displayed
clearly. If your windshield needs
replacing, it is recommended that
you have the work completed by a
NISSAN dealer.

JVI1787X

HOW TO USE THE HUD

To turn the HUD on, push the HUD switch.
To turn the HUD off, push the switch
again.

If the HUD is turned off, it will remain off
even if the vehicle is restarted.

The following settings can be changed in
the vehicle information display:

.

Brightness

.

Height

.

Rotation

.

Contents selection
— Navigation (if so equipped)

Instruments and controls

2-51

-------------------------------------------------------------------------------------------------------------------------------------------------------------

2-52

Instruments and controls

— Driving Assist
— Speed Limit Sign
— Audio
— TEL/SMS

.

Reset

NOTE:

Emergency information may be dis-
played even if the HUD is turned off.

This product includes the following soft-
ware.

(1) Panasonic Corporation or software
developed for Panasonic Corporation

(2) Third-party software licensed to Pana-
sonic Corporation

(3) Open source software

Regarding (3) Open source software, it
includes open source software (OSS),
including various software to which li-
cense information applies.

Refer to the license web site at: http://car.
panasonic.jp/oss/i02lln39

Display brightness

The brightness of the display may be
controlled in the vehicle information dis-
play. The brightness will also be adjusted
automatically according to the exterior
ambient lighting brightness.

WAC0516X

NOTE:

.

The HUD has a built-in sensor

that

controls the brightness of the dis-
played image. If you block the sen-
sor with an object, the display will
darken, making it difficult to see.
Make sure the sensor is clear of
obstructions.

.

Do not apply strong light to the
sensor. Doing so may cause a mal-
function.

DRIVER ASSISTANCE/NAVIGATION/
TRAFFIC SIGN/AUDIO/TEL/SMS
LINKING

The HUD will display Driver Assistance and
navigation information.

The Driver Assistance display will show
warning situations for the following sys-
tems:

.

Automatic Emergency Braking (AEB)
with Pedestrian Detection

.

Intelligent Forward Collision Warning
(I-FCW)

.

Lane Departure Warning (LDW)

.

Intelligent Lane Intervention (I-LI)

.

Hands-free warning (for vehicles with
ProPILOT Assist) (if so equipped)

The Navigation System linking display will
show the following items:

.

Intersection names

.

Arrows indicating turning direction

.

Distance to the next intersection

.

Recommended lane indicator

The Traffic Signs Recognition (TSR) sys-
tem linking display will show the following
items:

.

Speed Limit Sign

.

No Entry Sign

-------------------------------------------------------------------------------------------------------------------------------------------------------------

The Audio System linking display will
show the following items:

.

Songs

.

Radio stations

The TEL/SMS linking display will show the
following item:

.

Caller’s name or phone number

JVI1587X

Your vehicle has two types of security
systems, as follows:

.

V e h i c l e s e c u r i t y

s y s t e m

( i f s o

equipped)

.

NISSAN Vehicle Immobilizer System

VEHICLE SECURITY SYSTEM (if so
equipped)

The vehicle security system provides
visual and audio alarm signals if someone
opens the doors, hood and liftgate when
the system is armed. It is not, however, a
motion detection type system that acti-
vates when a vehicle is moved or when a
vibration occurs.

The system helps deter vehicle theft but
cannot prevent it, nor can it prevent the

theft of interior or exterior vehicle com-
ponents in all situations. Always secure
your vehicle even if parking for a brief
period. Never leave your keys in the
vehicle, and always lock it when unat-
tended. Be aware of your surroundings,
and park in secure, well-lit areas when-
ever possible.

Many devices offering additional protec-
tion, such as component locks, identifica-
tion markers, and tracking systems, are
available at auto supply stores and speci-
alty shops. Your NISSAN dealer may also
offer such equipment. Check with your
insurance company to see if you may be
eligible for discounts for various theft
protection features.

How to arm the vehicle security
system

1.

Close all windows.

The system can be

armed even if the windows are open.

2.

Remove the keys from the vehicle.

3.

Close all doors, hood and liftgate. Lock
all doors. The doors can be locked
with Intelligent Key, door handle re-
quest switch (if so equipped).

Even when the driver and/or passen-
gers are in the vehicle, the system will
activate with all the doors, hood and
liftgate locked with the ignition switch
placed in the OFF position. When pla-

Instruments and controls

2-53

SECURITY SYSTEMS

-------------------------------------------------------------------------------------------------------------------------------------------------------------

2-54

Instruments and controls

cing the ignition switch in the ON
position, the system will be released.

Vehicle security system activation

The vehicle security system will give the
following alarm:

.

The headlights or the hazard indicator
lights blink and the horn sounds
intermittently.

.

The alarm automatically turns off
after approximately 30 seconds. How-
ever, the alarm reactivates if the
vehicle is tampered with again.

The alarm is activated by:

.

opening any doors, the hood or lift-
gate without using Intelligent Key
(even if the door is unlocked by
releasing the door inside lock knob).

How to stop an activated alarm

The alarm stops by pushing the UNLOCK

button on the Intelligent Key, pushing

the request switch (if so equipped) in
range of the door handle or placing the
ignition switch in the ON position.

NISSAN VEHICLE IMMOBILIZER SYS-
TEM

The NISSAN Vehicle Immobilizer System
will not allow the engine to start without
the use of the registered key.

If the engine does not start using the
registered Intelligent Key, it may be due to
interference caused by:

.

Another Intelligent Key.

.

Automated toll road device.

.

Automated payment device.

.

Other devices that transmit similar
signals.

Start the engine using the following
procedure:

1.

Remove any items that may be caus-
ing the interference away from the
Intelligent Key.

2.

Start the engine again.

If this procedure allows the engine to
start, NISSAN recommends placing the
registered Intelligent Key separate from
other devices to avoid interference.

Statement related to section 15 of FCC
rules for NISSAN Vehicle Immobilizer
System (CONT ASSY-SMART KEYLESS)

FCC Notice:

For USA:

FCC ID : KR5HFM401

This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference,
and (2) this device must accept any
interference received, including inter-
ference that may cause undesired op-
eration.

Note: Changes or modifications not
expressly approved by the party re-
sponsible for compliance could void
the user’s authority to operate the
equipment.

For Canada:

IC ID : 7812D–HFM401

This device contains licence-exempt
transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence-exempt
RSS(s). Operation is subject to the fol-
lowing two conditions: (1) This device
may not cause interference. (2) This
device must accept any interference,
including interference that may cause
undesired operation of the device.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

WARNING

In freezing temperatures the washer
solution may freeze on the wind-
shield and obscure your vision which
may lead to an accident. Warm wind-
shield with the defroster before you
wash the windshield.

CAUTION

.

Do not operate the washer con-
tinuously for more than 30 sec-
onds.

.

Do not operate the washer if the
reservoir tank is empty.

.

Do not fill the window washer
reservoir tank with washer fluid
concentrates at full strength.
Some methyl alcohol based
washer fluid concentrates may
permanently stain the grille if
spilled while filling the window
washer reservoir tank.

.

Pre-mix washer fluid concen-
trates with water to the manu-
facturer’s recommended levels
before pouring the fluid into the
window washer reservoir tank. Do

not use the window washer re-
servoir tank to mix the washer
fluid concentrate and water.

If the windshield wiper operation is
interrupted by snow or ice, the wiper
may stop moving to protect its motor. If
this occurs, turn the wiper switch to the
OFF position and remove the snow or
ice that is on and around the wiper
arms. In approximately 1 minute, turn
the switch on again to operate the
wiper.

WAC0317X

WINDSHIELD WIPER AND WASHER
OPERATION

The windshield wiper and washer oper-
ates when the ignition switch is in the ON
position.

Push the lever down to operate the wiper
at the following speed:

Intermittent — intermittent operation can
be adjusted by turning the knob toward

(Faster) or

(Slower). Also, the inter-

mittent operation speed varies in accor-
dance with the vehicle speed. (For
example, when the vehicle speed is high,
the intermittent operation speed will be
faster.)

Low — continuous low speed operation

Instruments and controls

2-55

WIPER AND WASHER SWITCH

-------------------------------------------------------------------------------------------------------------------------------------------------------------

2-56

Instruments and controls

High — continuous high speed operation

Push the lever up

to have one sweep

operation of the wiper.

Pull the lever toward you

to operate the

washer. Then the wiper will also operate
several times.

NOTE:

The Speed Dependent feature may be
disabled. For additional information,
refer to “Vehicle Settings” (P.2-28).

CAUTION

Do not operate the windshield wiper
while the wiper arm is pulled up. The
wiper arm may be damaged.

REAR WINDOW WIPER AND WASHER
OPERATION

WARNING

In freezing temperatures the washer
solution may freeze on the rear
window glass and obscure your vi-
sion. Warm the rear window with the
defroster before you wash the rear
window.

CAUTION

.

Do not operate the washer con-
tinuously for more than 30 sec-
onds.

.

Do not operate the washer if the
reservoir tank is empty.

.

Do not fill the window washer
reservoir tank with washer fluid
concentrates at full strength.
Some methyl alcohol based
washer fluid concentrates may
permanently stain the grille if
spilled while filling the window
washer reservoir tank.

.

Pre-mix washer fluid concen-
trates with water to the manu-
facturer’s recommended levels
before pouring the fluid into the
window washer reservoir tank. Do
not use the window washer re-
servoir tank to mix the washer
fluid concentrate and water.

If the rear window wiper operation is
interrupted by snow or ice, the wiper
may stop moving to protect its motor. If
this occurs, turn the wiper switch to the
OFF position and remove the snow or
ice that is on and around the wiper

arms. In approximately 1 minute, turn
the switch on again to operate the
wiper.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

WAC0318X

The rear window wiper and washer
operate when the ignition switch is in
the ON position.

Turn the switch clockwise from the OFF
position to operate the wiper.

Intermittent (INT) — intermittent opera-
tion (not adjustable)

Low (ON) — continuous low speed opera-
tion

Push the switch forward

to operate the

washer. Then the wiper will also operate
several times.

Reverse Link feature:

When the windshield wiper switch is on,
moving the shift lever to the R (Reverse)
position will operate the rear window

wiper.

NOTE:

The Reverse Link feature may be dis-
abled. For additional information, refer
to “Vehicle Settings” (P.2-28).

WAC0418X

Type A (if so equipped)

WAC0419X

Type B (if so equipped)

Instruments and controls

2-57

REAR WINDOW AND OUTSIDE MIRROR
(if so equipped) DEFROSTER SWITCH

-------------------------------------------------------------------------------------------------------------------------------------------------------------

2-58

Instruments and controls

WAC0536X

Type C (if so equipped)

To defog/defrost the rear window glass
and outside mirrors (if so equipped), start
the engine and push the switch on. The
indicator light

will illuminate. Push the

switch again to turn the defroster off.

It will automatically turn off in approxi-
mately 20 minutes.

CAUTION

When cleaning the inner side of the
rear window, be careful not to
scratch or damage the rear window
defroster.

HEADLIGHT SWITCH

CAUTION

Use the headlights with the engine
running to avoid discharging the
vehicle battery.

WAC0533X

Example

Lighting

Type A (if so equipped):

Rotate the switch to the

position, and

the front parking, tail, license plate, and
instrument panel lights will come on.

Rotate the switch to the

position, and

the headlights will come on and all the
other lights remain on. The daytime run-
ning light will turn off.

HEADLIGHT AND TURN SIGNAL SWITCH

-------------------------------------------------------------------------------------------------------------------------------------------------------------

WAC1094X

Type B (if so equipped):

Rotate the switch to the

position, and

the front parking, tail, license plate, and
instrument panel lights will come on.

The Intelligent Auto Headlight system will
also be set in this position.

Rotate the switch to the

position, and

the headlights will come on and all the
other lights remain on. The daytime run-
ning light will turn off.

WAC0560X

Example

Intelligent Auto Headlight system

Type A (if so equipped):

The Intelligent Auto Headlight system
allows the headlights to be set so they
turn on and off automatically.

To set the Intelligent Auto Headlight
system:

1.

Make sure the headlight switch is in
the AUTO position

.

2.

Place the ignition switch in the ON
position.

3. The Intelligent Auto Headlight system

automatically turns the headlights on
and off.

To turn the Intelligent Auto Headlight
system off, turn the switch to the OFF,

or

position.

The Intelligent Auto Headlight system can
turn on the headlights automatically
when it is dark and turn off the headlights
when it is light.

The headlights will also be turned on
automatically at twilight or in rainy
weather (when the windshield wiper is
operated continuously).

If the ignition switch is placed in the OFF
position and one of the doors is opened
and this condition is continued, the head-
lights remain on for 5 minutes.

Instruments and controls

2-59

-------------------------------------------------------------------------------------------------------------------------------------------------------------

2-60

Instruments and controls

WAC1095X

Type B (if so equipped):

The Intelligent Auto Headlight system
allows the headlights to be set so they
turn on and off automatically.

To set the Intelligent Auto Headlight
system:

1.

Make sure the headlight switch is in
the

or AUTO position

.

2.

Place the ignition switch in the ON
position.

3. The Intelligent Auto Headlight system

automatically turns the headlights on
and off.

To turn the Intelligent Auto Headlight
system off, turn the switch to the

position.

The Intelligent Auto Headlight system can
turn on the headlights automatically
when it is dark and turn off the headlights
when it is light.

If the ignition switch is placed in the ON
position when the parking brake is ap-
plied, the headlights remain off.

With the

position selected, the head-

lights turn off when the ignition switch is
placed in the OFF position, the shift
position is placed in the P (Park) position
or the parking brake is applied. (The front
parking, tail, license plate, and instrument
panel lights are on.)

The headlights will also be turned on
automatically at twilight or in rainy
weather (when the windshield wiper is
operated continuously).

With the AUTO position selected (head-
lights are on), if the ignition switch is
placed in the OFF position and one of the
doors is opened and this condition is
continued, the headlights remain on for
5 minutes.

WAC0522X

Be sure not to put anything on top of
the photo sensor

located on the top

of the instrument panel. The photo
sensor controls the Intelligent Auto
Headlight; if it is covered, the photo
sensor reacts as if it is dark and the
headlights will illuminate.

Automatic headlights off delay:

You can keep the headlights on for up to
180 seconds after you place the ignition
switch in the OFF and open any door then
close all the doors. You can adjust the
period of the automatic headlights off
delay from 0 seconds (OFF) to 180 sec-
onds. The factory default setting is 45
seconds.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

For automatic headlights off delay
setting, see “Vehicle Settings” (P.2-28).

WAC1096X

Example

Headlight beam select

To select the high beam, push the lever
forward and release it. The high beam
lights come on and the

light illumi-

nates.

Pull the lever back and release it to select
the low beam.

To flash the headlights when the high
beam is not selected, pull the lever
towards the rear position. To flash the
headlights when the high beam is se-
lected, pull the lever twice towards the
rear position.

High beam assist

The high beam assist system will operate
when the vehicle is driven at speeds of
approximately 19 MPH (30 km/h) and
above. If an oncoming vehicle or leading
vehicle appears in front of your vehicle
when the headlight high beam is on, the
headlight will be switched to the low
beam automatically.

Precautions on high beam assist:

WARNING

.

The high beam assist system is a
convenience but it is not a sub-
stitute for safe driving operation.
The driver should remain alert at
all times, ensure safe driving
practices and switch the high
beams and low beam manually
when necessary.

.

The high beam or low beam may
not switch automatically under
the following conditions. Switch
the high beam and low beam
manually.

— During bad weather (rain, fog,

snow, wind, etc.).

— When a light source similar to

a headlight or tail light is in

Instruments and controls

2-61

-------------------------------------------------------------------------------------------------------------------------------------------------------------

2-62

Instruments and controls

the vicinity of the vehicle.

— When the headlights of the

oncoming vehicle or the lead-
ing vehicle are turned off,
when the color of the light is
affected due to foreign mate-
rials on the lights, or when the
light beam is out of position.

— When there is a sudden, con-

tinuous change in brightness.

— When driving on a road that

passes over rolling hills, or a
road that has level differ-
ences.

— When driving on a road with

many curves.

— When a sign or mirror-like

surface is reflecting intense
light towards the front of the
vehicle.

— When the container, etc. being

towed by a leading vehicle is
reflecting intense light.

— When a headlight on your

vehicle is damaged or dirty.

— When the vehicle is leaning at

an angle due to a punctured
tire, being towed, etc.

.

The timing of switching the low
b e a m a n d h i g h b e a m m a y
change under the following situa-
tions.

— The brightness of the head-

lights of the oncoming vehicle
or leading vehicle.

— The movement and direction

of the oncoming vehicle and
the leading vehicle.

— When only one light on the

oncoming vehicle or the lead-
ing vehicle is illuminated.

— When the oncoming vehicle or

the leading vehicle is a two-
wheeled vehicle.

— R o a d c o n d i t i o n s ( i n c l i n e ,

curve, the road surface, etc.).

— The number of passengers

and the amount of cargo.

WAC1097X

Example

High beam assist operations:

To activate the high beam assist system,
push the switch as illustrated with the
AUTO position (or

position, depend-

ing on the model). The high beam assist
indicator light in the meter will illuminate
while the headlights are turned on.

If the high beam assist indicator light
does not illuminate in the above condi-
tion, it may indicate that the system is not
functioning properly. It is recommended
you have the system checked by a
NISSAN dealer.

When the vehicle speed lowers to less
than approximately 13 MPH (20 km/h), the

-------------------------------------------------------------------------------------------------------------------------------------------------------------

headlight remains the low beam.

To turn off the high beam assist system,
push the switch again.

WAC0523X

Ambient image sensor maintenance:

The ambient image sensor

for the high

beam assist system is located in front of
the inside mirror. To keep the proper
operation of the high beam assist system
and prevent a system malfunction, be
sure to observe the following:

.

Always keep the windshield clean.

.

Do not attach a sticker (including
transparent material) or install an
accessory near the ambient image
sensor.

.

Do not strike or damage the areas
around the ambient image sensor. Do
not touch the sensor lens that is
located on the ambient image sensor.

If the ambient image sensor is damaged
due to an accident, it is recommended
you contact a NISSAN dealer.

Battery saver system

.

When the headlight switch is in the

or

position while the ignition

switch is in the ON position, the lights
will automatically turn off within a
period of time after the ignition switch
has been placed in the OFF position.

.

When the headlight switch remains in
the

or

position after the lights

automatically turn off, the lights will
turn on when the ignition switch is
placed in the ON position.

CAUTION

.

When you turn on the headlight
switch again after the lights auto-
matically turn off, the lights will
not turn off automatically. Be
sure to turn the light switch to
the OFF (if so equipped) or the
AUTO position when you leave
the vehicle for extended periods
of time, otherwise the battery will
be discharged.

.

Never leave the light switch on
when the engine is not running

Instruments and controls

2-63

-------------------------------------------------------------------------------------------------------------------------------------------------------------

2-64

Instruments and controls

for extended periods of time even
if the headlights turn off auto-
matically.

Daytime Running Light (DRL) sys-
tem

The LED Daytime Running Lights (DRL)
automatically illuminate when the engine
is started and the parking brake is
released. The LED DRL operate with the
headlight switch in the OFF (if so
equipped),

, or AUTO (when the head-

lights are off) position. When you turn the
headlight switch to the

position for

full illumination, the LED lights switch
from LED DRL to the park function.

Type A:

If the parking brake is applied

before the engine is started, the LED DRL
do not illuminate. The LED DRL illuminate
when the parking brake is released. This
feature will work in the

, AUTO or OFF

position. The LED DRL will remain on until
the ignition switch is placed in the OFF
position.

Type B:

If the parking brake is applied

before the engine is started, the LED DRL
do not illuminate. The LED DRL illuminate
when the parking brake is released. This
feature will work in the AUTO or
position. The LED DRL will remain on until
the ignition switch is placed in the OFF

position.

WARNING

When the LED DRL system is active
with the headlight switch in the OFF
position (if so equipped), tail lights
on your vehicle are not on. It is
necessary at dusk to turn on your
headlights. Failure to do so could
cause an accident injuring yourself
and others.

WAC1098X

Example

TURN SIGNAL SWITCH

Turn signal

Move the lever up or down to signal the
turning direction. When the turn is com-
pleted, the turn signals cancel automati-
cally.

Lane change signal

Move the lever up or down until the turn
signal begins to flash, but the lever does
not latch, to signal a lane change. Hold
the lever until the lane change is com-
pleted.

Move the lever up or down until the turn
signal begins to flash, but the lever does

-------------------------------------------------------------------------------------------------------------------------------------------------------------

 

 

 

 

 

 

 

Content      ..     7      8      9      10     ..