Nissan Titan (2023 year). Manual in english - page 30

 

  Index      Manuals     Nissan Titan (2023 year). Manual in english

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

 

 

 

Content      ..     28      29      30      31     ..

 

 

 

Nissan Titan (2023 year). Manual in english - page 30

 

 

Do not attempt to start the engine by
pushing.

CAUTION

Automatic transmission models can-
not be push-started or tow-started.
Attempting to do so may cause
transmission damage.

Three way catalyst equipped models
should not be started by pushing
since the three way catalyst may be
damaged.

Never try to start the vehicle by tow-
ing it; when the engine starts, the for-
ward surge could cause the vehicle to
collide with the tow vehicle.

WARNING

Do not continue to drive if your ve-
hicle overheats. Doing so could cause
engine damage or a vehicle fire.

To avoid the danger of being scalded,
never remove the radiator or coolant
reservoir cap while the engine is still
hot. When the radiator or coolant res-
ervoir cap is removed, pressurized
hot water will spurt out, possibly
causing serious injury.

Do not open the hood if steam is
coming out.

If your vehicle is overheating (indicated by
an extremely high temperature gauge
reading), or if you feel a lack of engine
power, detect abnormal noise, etc. take the
following steps:

1. Move the vehicle safely off the road, ap-

ply the parking brake and move the shift
lever to P (Park).

Do not stop the engine.

2. Turn off the air conditioner. Open all the

windows, move the heater or air condi-
tioner temperature control to maximum
hot and fan control to high speed.

3. If engine overheating is caused by

climbing a long hill on a hot day, run the
engine at a fast idle (approximately 1,500
rpm) until the temperature gauge indi-
cation returns to normal.

4. Get out of the vehicle. Look and listen for

steam or coolant escaping from the ra-
diator before opening the hood. If steam
or coolant is escaping, turn off the en-
gine. Do not open the hood further until
no steam or coolant can be seen.

5. Open the engine hood.

WARNING

If steam or water is coming from the
engine, stand clear to prevent getting
burned.

6. Visually check drive belts for damage or

looseness. Also check if the cooling fan
is running. The radiator hoses and radia-
tor should not leak water. If coolant is
leaking, the water pump belt is missing
or loose, or the cooling fan does not run,
stop the engine.

PUSH STARTING

IF YOUR VEHICLE OVERHEATS

6-12

In case of emergency

-------------------------------------------------------------------------------------------------------------------------------------------------------------

WARNING

Be careful not to allow your hands, hair,
jewelry or clothing to come into con-
tact with, or get caught in, engine belts
or the engine cooling fan. The engine
cooling fan can start at any time.

7. After the engine cools down, check the

coolant level in the engine coolant reser-
voir tank with the engine running. Add
coolant to the engine coolant reservoir
tank if necessary. It is recommended
that you visit a NISSAN dealer for this
service.

When towing your vehicle, all jurisdictional
and local regulations for towing must be
followed.

Incorrect

towing

equipment

could damage your vehicle. Towing in-
structions are available from a NISSAN
dealer. Local service operators are gener-
ally familiar with the applicable laws and
procedures for towing. To assure proper
towing and to prevent accidental damage
to your vehicle, NISSAN recommends hav-
ing a service operator tow your vehicle. It is
advisable to have the service operator
carefully read the following precautions:

WARNING

Never ride in a vehicle that is being
towed.

Never get under your vehicle after it
has been lifted by a tow truck.

If your vehicle has front recovery
hooks as original factory equipment,
do not remove or modify them. If it
was not equipped with front recov-
ery hooks, do not install them. Either
action could affect proper operation
of the front air bag system resulting
in injury or death.

CAUTION

When towing, make sure that the
transmission, axles, steering system
and powertrain are in working condi-
tion. Use dollies or flatbed if any of
the listed systems are not working.

Always attach safety chains before
towing.

For additional information about towing
your vehicle behind a Recreational Vehicle
(RV), see "Flat towing for 2-Wheel Drive
(2WD) vehicle" (P. 10-53) or "Flat towing for
4-Wheel Drive (4WD) vehicle" (P. 10-53).

TOWING RECOMMENDED BY
NISSAN

NISSAN recommends towing your vehicle
based upon the type of drivetrain. For addi-
tional information, refer to the diagrams in
this section to ensure that your vehicle is
properly towed.

TOWING YOUR VEHICLE

In case of emergency

6-13

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Four-Wheel Drive (4WD) models
with automatic transmission

NISSAN recommends that towing dollies
be used when towing your vehicle or place
the vehicle on a flatbed truck as illustrated.

CAUTION

Never tow 4WD models equipped with
an automatic transmission with any of
the wheels on the ground as this may
cause serious and expensive damage
to the transfer case and transmission.

NOTE:

If the battery is completely drained the
transmission will not manually shift to
other positions.

LCE2141

6-14

In case of emergency

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Two-Wheel Drive models with
automatic transmission

NISSAN recommends that your vehicle be
towed with the driving (rear) wheels off the
ground or place the vehicle on a flatbed
truck as illustrated.

CAUTION

Never tow automatic transmission
models with the rear wheels on the
ground or four wheels on the ground
(forward or backward), as this may
cause serious and expensive dam-
age to the transmission. If it is neces-
sary to tow the vehicle with the front
wheels raised always use towing dol-
lies under the rear wheels.

When towing automatic transmis-
sion models with the front wheels on
the ground or on towing dollies:

Place the ignition switch in the

OFF position and secure the steer-
ing wheel in a straight-ahead po-
sition with a rope or similar de-
vice. Never secure the steering
wheel by placing the ignition
switch in the LOCK position. This
may cause damage to the lock
mechanism (for models with a
steering lock mechanism).

NOTE:

If the battery is completely drained the
transmission will not manually shift to
other positions.

When towing long distances or speeds in
excess of 50 mph (80 km/h), remove the
propeller shaft before towing to prevent
damage to the transmission. It is recom-
mended that you visit a NISSAN dealer for
additional information.

VEHICLE RECOVERY (freeing a
stuck vehicle)

There are two options to recover a stuck
vehicle: pulling and rocking. For additional
information

regarding

these

options,

please refer to the following sections.

LCE2311

In case of emergency

6-15

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Pulling a stuck vehicle

WARNING

To avoid vehicle damage, serious per-
sonal injury or death when recovering a
stuck vehicle:

Contact a professional towing ser-
vice to recover the vehicle if you have
any questions regarding the recov-
ery procedure.

Attach recovery devices only to main
structural members of the vehicle or
the recovery hooks (if so equipped).

Do not use the vehicle tie-downs to
tow or free a stuck vehicle.

Only use devices specifically de-
signed for vehicle recovery and fol-
low the manufacturer's instructions.

Always

pull

the

recovery

device

straight out from the front of the ve-
hicle. Never pull at an angle.

Route recovery devices so they do
not touch any part of the vehicle ex-
cept the attachment point.

If your vehicle is stuck in sand, snow, mud,
etc., use a tow strap or other device de-
signed specifically for vehicle recovery. Al-
ways follow the manufacturer's instruc-
tions for the recovery device.

Rocking a stuck vehicle

WARNING

Stand clear of a stuck vehicle.

Do not spin your tires at high speed.
This could cause them to explode
and result in serious injury. Parts of
your vehicle could also overheat and
be damaged.

If your vehicle is stuck in sand, snow, mud,
etc., use the following procedure:

1. Turn off the Vehicle Dynamic Control

(VDC) system.

2. Activate the Electronic Locking Rear Dif-

ferential

(E-Lock)

system

(if

so

equipped). For additional information,
see “Electronic Locking Rear Differential
(E-Lock) system” (P. 5-111)

3. Make sure the area in front and behind

the vehicle is clear of obstructions.

4. Turn the steering wheel right and left to

clear an area around the front tires.

5. Slowly rock the vehicle forward and

backward.

• Shift back and forth between R (Re-

verse) and D (Drive).

• Apply the accelerator as little as pos-

sible to maintain the rocking motion.

• Release the accelerator pedal before

shifting between R (Reverse) and D
(Drive).

• Do not spin the tires above 34 mph (55

km/h) or above 12 mph (20 km/h) if the
E–Lock system (if so equipped) is
engaged.

6. If the vehicle cannot be freed after a few

tries, contact a professional towing ser-
vice to remove the vehicle.

6-16

In case of emergency

-------------------------------------------------------------------------------------------------------------------------------------------------------------

7 Appearance and care

Cleaning exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2

Washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Waxing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Removing spots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Underbody . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Glass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Aluminum alloy wheels (if so equipped) . . . . . . . 7-3
Chrome parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Tire dressings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4

Cleaning interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4

Air fresheners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
Power moonroof (if so equipped) . . . . . . . . . . . . . 7-5
Floor mats (if so equipped) . . . . . . . . . . . . . . . . . . . 7-5
Seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6

Corrosion protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7

Most common factors contributing to
vehicle corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7
Environmental factors influence the
rate of corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7
Protect your vehicle from corrosion . . . . . . . . . . 7-7

-------------------------------------------------------------------------------------------------------------------------------------------------------------

In order to maintain the appearance of
your vehicle, it is important to take proper
care of it.

To protect the paint surfaces, wash your
vehicle as soon as you can:
• After a rainfall to prevent possible dam-

age from acid rain.

• After driving on coastal roads.
• When contaminants such as soot, bird

droppings, tree sap, metal particles or
bugs get on the paint surface.

• When dust or mud builds up on the

surface.

Whenever possible, store or park your ve-
hicle inside a garage or in a covered area.

When it is necessary to park outside, park in
a shady area or protect the vehicle with a
body cover.

Be careful not to scratch the paint sur-
face when putting on or removing the
body cover.

WASHING

Wash dirt off with a wet sponge and plenty
of water. Clean the vehicle thoroughly us-
ing a mild soap, a special vehicle soap or
general purpose dishwashing liquid mixed
with clean, lukewarm (never hot) water.

CAUTION

Do not concentrate water spray di-
rectly on the sonar sensors (if so
equipped) on the bumper as this will
result in damage to the sensors. Do
not use pressure washers capable of
spraying water over 1,200 psi (8,274
kPa) to wash your vehicle. Use of
high-pressure washers over 1,200 psi
(8,274 kPa) can result in damage to or
removal of paint or graphics. Avoid
using a high-pressure washer closer
than 12 inches (30 cm) to the vehicle.
Always use a wide-angle nozzle only,
keep the nozzle moving and do not
concentrate the water spray on any
one area.

Do not use car washes that use acid
in the detergent. Some car washes,
especially brushless ones, use some
acid for cleaning. The acid may react
with some plastic vehicle compo-
nents, causing them to crack. This
could affect their appearance, and
also could cause them not to func-
tion properly. Always check with your
car wash to confirm that acid is not
used.

Do not wash the vehicle with strong
household soap, strong chemical de-
tergents, gasoline or solvents.

Do not wash the vehicle in direct sun-
light or while the vehicle body is hot,
as

the

surface

may

become

water-spotted.

Avoid using tight-napped or rough
cloths, such as washing mitts. Care
must

be

taken

when

removing

caked-on dirt or other foreign sub-
stances so the paint surface is not
scratched or damaged.

Rinse the vehicle thoroughly with plenty of
clean water.

Inside edges, seams and folds on the
doors, hatches and hood are particularly
vulnerable to the effects of road salt. There-
fore, these areas must be cleaned regularly.
Take care that the drain holes in the lower
edge of the door are open. Spray water
under the body and in the wheel wells to
loosen the dirt and wash away road salt.

A damp chamois can be used to dry the
vehicle to avoid water spots.

WAXING

Regular waxing protects the paint surface
and helps retain new vehicle appearance.

CLEANING EXTERIOR

7-2

Appearance and care

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Polishing is recommended to remove
built-up wax residue and to avoid a weath-
ered appearance before re-applying wax.

A NISSAN dealer can assist you in choosing
the proper product.
• Wax your vehicle only after a thorough

washing. Follow the instructions supplied
with the wax.

• Do not use a wax containing any abra-

sives, cutting compounds or cleaners
that may damage the vehicle finish.

Machine compounding or aggressive pol-
ishing on a base coat/clear coat paint fin-
ish may dull the finish or leave swirl marks.

REMOVING SPOTS

Remove tar and oil spots, industrial dust,
insects, and tree sap as quickly as possible
from the surface of the paint to avoid last-
ing damage or staining. Special cleaning
products are available at a NISSAN dealer
or any automotive accessory store. It is
recommended that you visit a NISSAN
dealer for these products.

UNDERBODY

In areas where road salt is used in winter, it
is necessary to clean the underbody regu-
larly in order to prevent dirt and salt from

building up and causing the acceleration of
corrosion on the underbody and suspen-
sion. Before the winter period and again in
the spring, the underseal must be checked
and, if necessary, re-treated.

GLASS

Use glass cleaner to remove smoke and
dust film from the glass surfaces. It is nor-
mal for glass to become coated with a film
after the vehicle is parked in the hot sun.
Glass cleaner and a soft cloth will easily
remove this film.

CAUTION

When cleaning the inside of the win-
dows, do not use sharp-edged tools,
abrasive cleaners or chlorine-based
disinfectant cleaners. They could dam-
age the electrical conductors, radio an-
tenna elements or rear window de-
froster elements.

ALUMINUM ALLOY WHEELS (if so
equipped)

Wash the wheels regularly with a sponge
dampened in a mild soap solution, espe-
cially during winter months in areas where
road salt is used. If not removed, road salt
can discolor the wheels.

CAUTION

Follow the directions below to avoid
staining or discoloring the wheels:

Do not use a cleaner that uses strong
acid or alkali contents to clean the
wheels.

Do not apply wheel cleaners to the
wheels when they are hot. The wheel
temperature should be the same as
ambient temperature.

Do not use chrome cleaner on any
wheel. Doing so can damage the
chrome-like coating on the wheel.

Rinse the wheel to completely re-
move the cleaner within 15 minutes
after the cleaner is applied.

CHROME PARTS

Clean all chrome parts regularly with a
non-abrasive chrome polish to maintain
the finish.

CAUTION

Do not use chrome cleaner on any
wheel. Doing so can damage the
chrome-like coating on the wheel.

Appearance and care

7-3

-------------------------------------------------------------------------------------------------------------------------------------------------------------

TIRE DRESSINGS

NISSAN does not recommend the use of
tire dressings. Tire manufacturers apply a
coating to the tires to help reduce discolor-
ation of the rubber. If a tire dressing is ap-
plied to the tires, it may react with the coat-
ing and form a compound. This compound
may come off the tire while driving and
stain the vehicle paint.

If you choose to use a tire dressing, take the
following precautions:
• Use a water-based tire dressing. The

coating on the tire dissolves more easily
than with an oil-based tire dressing.

• Apply a light coat of tire dressing to help

prevent it from entering the tire tread/
grooves (where it would be difficult to
remove).

• Wipe off excess tire dressing using a dry

towel. Make sure the tire dressing is com-
pletely

removed

from

the

tire

tread/grooves.

• Allow the tire dressing to dry as recom-

mended

by

the

tire

dressing

manufacturer.

Occasionally remove loose dust from the
interior trim, plastic parts and seats using a
vacuum cleaner or soft bristled brush. Wipe
the vinyl and leather surfaces (if so
equipped) with a clean, soft cloth damp-
ened in mild soap solution, then wipe clean
with a dry, soft cloth.

Regular care and cleaning is required in
order to maintain the appearance of the
leather (if so equipped).

Before using any fabric protector, read the
manufacturer's recommendations. Some
fabric protectors contain chemicals that
may stain or bleach the seat material.

Use a cloth dampened only with water to
clean the meter and gauge lens.

WARNING

Do not use water or acidic cleaners (hot
steam cleaners) on the seat. This can
damage the seat or occupant classifi-
cation sensor (if so equipped). This can
also affect the operation of the air bag
system and result in serious personal
injury.

CAUTION

Never use benzine, thinner or any
similar material.

Small dirt particles can be abrasive
and damaging to leather surfaces
and should be removed promptly. Do
not use saddle soap, car waxes, pol-
ishes, oils, cleaning fluids, solvents,
detergents

or

ammonia-based

cleaners as they may damage the
leather's natural finish.

Never use fabric protectors unless
recommended by the manufacturer.

Do not use glass or plastic cleaner on
meter or gauge lens covers. It may
damage the lens cover.

Never use chloride solutions for
cleaning aluminum decoratives (if so
equipped), damage may occur.

CLEANING INTERIOR

7-4

Appearance and care

-------------------------------------------------------------------------------------------------------------------------------------------------------------

AIR FRESHENERS

Most air fresheners use a solvent that
could affect the vehicle interior. If you use
an

air

freshener,

take

the

following

precautions:
• Hanging-type air fresheners can cause

permanent discoloration when they con-
tact vehicle interior surfaces. Place the air
freshener in a location that allows it to
hang free and not contact an interior
surface.

• Liquid-type air fresheners typically clip on

the vents. These products can cause im-
mediate

damage

and

discoloration

when spilled on interior surfaces.

Carefully read and follow the manufactur-
er's instructions before using the air
fresheners.

POWER MOONROOF (if so
equipped)

The sunshade is made from a tricot
material.

CAUTION

To help prevent damaging the moon-
roof while cleaning:

Do not rub the material with a cloth.
Doing so can damage the surface of
the material or cause a stain to
spread.

Never use benzine, thinner or any
similar chemical to clean the sun-
shade. This may discolor the moon-
roof and damage the surface.

Clean water based stains by patting
the surface with a clean soft cloth
dampened in warm water. Press a
clean dry cloth onto the surface to
remove as much dampness as pos-
sible and then let air dry.

Clean oil based stains by patting the
surface with a clean soft cloth damp-
ened in warm water. Press a clean dry
cloth onto the surface to remove as
much dampness as possible and
then let air dry.

FLOOR MATS (if so equipped)

WARNING

To avoid potential pedal interference
that may result in a collision, injury or
death:

NEVER place a floor mat on top of
another floor mat in the driver front
position or install them upside down
or backwards.

Use only Genuine NISSAN floor mats,
or equivalent floor mats, that are
specifically designed for use in your
vehicle model and model year.

LPD2417

Appearance and care

7-5

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Properly position the mats in the
floorwell using the floor mat posi-
tioning hook. For additional informa-
tion, see "Floor mat installation"
(P. 7-6).

Make sure the floor mat does not in-
terfere with pedal operation.

Periodically check the floor mats to
make

sure

they

are

properly

installed.

After cleaning the vehicle interior,
check the floor mats to make sure
they are properly installed.

The use of Genuine NISSAN floor mats can
extend the life of your vehicle carpet and
make it easier to clean the interior. Mats
should be maintained with regular clean-
ing and replaced if they become exces-
sively worn.

Floor mat installation

Your vehicle is equipped with floor mat po-
sitioning hook(s). The number and shape of
the floor mat positioning hooks for each
seating position varies depending on the
vehicle.

When installing Genuine NISSAN floor mats,
follow the installation instructions provided
with the mat and the following:

1. With the ignition switch in the OFF posi-

tion, the shift lever in P (Park) position
and with the parking brake fully applied,
position the floor mat in the floorwell so
that the floor mat grommet holes are
aligned with the hook(s).

2. Secure the grommet holes into the

hook(s) and ensure that the floor mat is
properly positioned.

3. Make sure the floor mat does not inter-

fere with pedal operation. With the igni-
tion switch still in the OFF position, the
shift lever in the P (Park) position and
with the parking brake applied, fully ap-
ply and release all pedals. The floor mat
must not interfere with pedal operation
or prevent the pedal from returning to
its normal position.

It is recommended that you visit a NISSAN
dealer for details about installing the floor
mats in your vehicle.

The illustration shows the location of the
floor mat positioning hooks.

SEAT BELTS

The seat belts can be cleaned by wiping
them with a sponge dampened in a mild
soap solution. Allow the belts to dry com-
pletely in the shade before using them. For
additional information, see “Seat belt main-
tenance” (P. 1-23).

LAI2088

Positioning hooks

7-6

Appearance and care

-------------------------------------------------------------------------------------------------------------------------------------------------------------

WARNING

Do not allow wet seat belts to roll up in
the retractor. NEVER use bleach, dye or
chemical solvents to clean the seat
belts, since these materials may se-
verely weaken the seat belt webbing.

MOST COMMON FACTORS
CONTRIBUTING TO VEHICLE
CORROSION

Most vehicle corrosion is caused by:
• The accumulation of moisture-retaining

dirt and debris in body panel sections,
cavities, and other areas.

• Damage to paint and other protective

coatings caused by gravel and stone
chips or minor traffic collisions.

ENVIRONMENTAL FACTORS
INFLUENCE THE RATE OF
CORROSION

Moisture

Accumulation of sand, dirt and water on
the vehicle body underside can accelerate
corrosion. Wet floor coverings will not dry
completely inside the vehicle and should
be removed for drying to avoid floor panel
corrosion.

Relative humidity

Corrosion will be accelerated in areas of
high relative humidity, especially those ar-
eas where the temperatures stay above
freezing and where atmospheric pollution
exists and road salt is used.

Temperature

High temperatures accelerate the rate of
corrosion to those parts which are not well
ventilated.

Air pollution

Industrial pollution, the presence of salt in
the air in coastal areas, or heavy road salt
use accelerates the corrosion process.
Road salt also accelerates the disintegra-
tion of paint surfaces.

PROTECT YOUR VEHICLE FROM
CORROSION

• Wash and wax your vehicle often to keep

the vehicle clean.

• Always check for minor damage to the

paint and repair it as soon as possible.

• Keep drain holes at the bottom of the

doors open to avoid water accumulation.

• Check the underbody for accumulation

of sand, dirt or salt. If present, wash with
water as soon as possible.

CORROSION PROTECTION

Appearance and care

7-7

-------------------------------------------------------------------------------------------------------------------------------------------------------------

CAUTION

NEVER remove dirt, sand or other de-
bris from the passenger compart-
ment by washing it out with a hose.
Remove dirt with a vacuum cleaner
or broom.

Never allow water or other liquids to
come in contact with electronic com-
ponents inside the vehicle as this
may damage them.

Chemicals used for road surface de-icing
are extremely corrosive. They accelerate
corrosion and deterioration of underbody
components such as the exhaust system,
fuel and brake lines, brake cables, floor pan
and fenders.

In

winter,

the

underbody

must

be

cleaned periodically.

For additional protection against rust and
corrosion, which may be required in some
areas, it is recommended that you visit a
NISSAN dealer.

7-8

Appearance and care

-------------------------------------------------------------------------------------------------------------------------------------------------------------

8 Do-it-yourself

Maintenance precautions . . . . . . . . . . . . . . . . . . . . . . . 8-2
Engine compartment check locations . . . . . . . . . . . 8-4
Engine cooling system . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6

Checking engine coolant level . . . . . . . . . . . . . . . . 8-7
Changing engine coolant . . . . . . . . . . . . . . . . . . . . 8-7

Engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8

Checking engine oil level . . . . . . . . . . . . . . . . . . . . . 8-8
Changing engine oil and oil filter . . . . . . . . . . . . . . 8-8

Automatic Transmission Fluid (ATF) . . . . . . . . . . . . . 8-14
Power Steering Fluid (PSF) . . . . . . . . . . . . . . . . . . . . . . 8-14
Brake fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-15
Windshield-washer fluid . . . . . . . . . . . . . . . . . . . . . . . . 8-16

Windshield-washer fluid reservoir . . . . . . . . . . . 8-16

Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-17

Jump starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-20

Variable voltage control system . . . . . . . . . . . . . . . . 8-20
Drive belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-21
Spark plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-21

Replacing spark plugs . . . . . . . . . . . . . . . . . . . . . . . 8-21

Air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-22

In-cabin microfilter . . . . . . . . . . . . . . . . . . . . . . . . . . 8-22

Windshield wiper blades . . . . . . . . . . . . . . . . . . . . . . . . 8-23

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-23
Replacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-23

Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-24
Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-25

Engine compartment . . . . . . . . . . . . . . . . . . . . . . . 8-25
Passenger compartment . . . . . . . . . . . . . . . . . . . 8-27

Battery replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-28

NISSAN Intelligent Key® . . . . . . . . . . . . . . . . . . . . . . 8-28

Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-30

Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-30
Fog lights (if so equipped) . . . . . . . . . . . . . . . . . . . 8-31
Exterior and interior lights . . . . . . . . . . . . . . . . . . . 8-31

Wheels and tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-34

Tire pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-34
Tire labeling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-38
Types of tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-42
Tire chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-43
Changing wheels and tires . . . . . . . . . . . . . . . . . . 8-44

-------------------------------------------------------------------------------------------------------------------------------------------------------------

When performing any inspection or main-
tenance work on your vehicle, always take
care to prevent serious accidental injury to
yourself or damage to the vehicle. The fol-
lowing are general precautions which
should be closely observed.

WARNING

Park the vehicle on a level surface,
apply the parking brake securely and
block the wheels to prevent the ve-
hicle from moving. Move the shift le-
ver to P (Park)

Be sure the ignition switch is in the
OFF or LOCK position when perform-
ing any parts replacement or repairs.

If you must work with the engine run-
ning, keep your hands, clothing, hair
and tools away from moving fans,
belts and any other moving parts.

It is advisable to secure or remove
any loose clothing and remove any
jewelry, such as rings, watches, etc.
before working on your vehicle.

Always wear eye protection when-
ever you work on your vehicle.

The automatic engine cooling fan (if
so equipped) may come on at any
time without warning, even if the ig-
nition switch is in the OFF position
and the engine is not running. To
avoid injury, always disconnect the
negative battery cable before work-
ing near the fan.

If you must run the engine in an en-
closed space such as a garage, be
sure there is proper ventilation for
exhaust gases to escape.

Never get under the vehicle while it is
supported only by a jack. If it is nec-
essary to work under the vehicle,
support it with safety stands.

Keep smoking materials, flame and
sparks away from the fuel tank and
battery.

Because the fuel lines are under high
pressure even when the engine is off,
it is recommended that you visit a
NISSAN dealer for service of the fuel
filter or fuel lines.

CAUTION

Do not work under the hood while
the engine is hot. Turn the engine off
and wait until it cools down.

Avoid contact with used engine oil
and coolant. Improperly disposed
engine oil, engine coolant and/or
other vehicle fluids can damage the
environment. Always conform to lo-
cal regulations for disposal of vehicle
fluid.

Never leave the engine or automatic
transmission

related

component

harnesses disconnected while the
ignition switch is in the ON position.

Never connect or disconnect the bat-
tery or any transistorized compo-
nent while the ignition switch is in
the ON position.

MAINTENANCE PRECAUTIONS

8-2

Do-it-yourself

-------------------------------------------------------------------------------------------------------------------------------------------------------------

NOTE:

If the battery is completely drained the
transmission will not manually shift to
other positions.

This “Do-it-yourself ” section gives instruc-
tions regarding only those items which are
relatively easy for an owner to perform.

A Genuine NISSAN service manual is also
available. For additional information, see
“Owner's Manual/Service Manual order in-
formation” (P. 10-58).

You should be aware that incomplete or
improper servicing may result in operating
difficulties or excessive emissions, and
could affect warranty coverage.

If in doubt

about any servicing, it is recommended
that you have it done by a NISSAN dealer.

Do-it-yourself

8-3

-------------------------------------------------------------------------------------------------------------------------------------------------------------

 

 

 

 

 

 

 

Content      ..     28      29      30      31     ..