Nissan Z (2023 year). Manual in english - page 21

 

  Index      Manuals     Nissan Z (2023 year). Manual in english

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

 

 

 

Content      ..     19      20      21      22     ..

 

 

 

Nissan Z (2023 year). Manual in english - page 21

 

 

ENGINE COMPARTMENT

WARNING

Never use a fuse of a higher or lower

amperage rating than that specified

on the fuse box cover. This could

damage the electrical system or

electronic control units or cause a

fire.

If any electrical equipment does not

operate, check for an open fuse.
1. Be sure the ignition switch is pushed

to the OFF or LOCK position and the

headlight switch is in the OFF (if so

equipped) or AUTO position and the

headlights are OFF.

2. Open the engine hood.
3. Remove the fuse/fusible link holder

cover.

4. Remove the fuse with the fuse puller

located in the passenger compart-

ment fuse box.

SDI1754

5. If the fuse is open

, replace it with a

new fuse

. Spare fuses are stored in

the passenger compartment fuse box.

6. If a new fuse also opens, have the

electrical system checked and re-

paired. It is recommended you visit a

NISSAN dealer for this service.

Fusible links

If any electrical equipment does not

operate and fuses are in good condition,

check the fusible links. If any of these

fusible links are melted, replace only with

genuine NISSAN parts.

Do-it-yourself

8-19

-------------------------------------------------------------------------------------------------------------------------------------------------------------

8-20

Do-it-yourself

WAI0342X

PASSENGER COMPARTMENT

WARNING

Never use a fuse of a higher or lower

amperage rating than that specified

on the fuse box cover. This could

damage the electrical system or

electronic control units or cause a

fire.

If any electrical equipment does not

operate, check for an open fuse.
1. Be sure the ignition switch is pushed

to the OFF or LOCK position and the

headlight switch is in the OFF (if so

equipped) or AUTO position and the

headlights are OFF.

2. Open the fuse box cover.
3. Remove the fuse with the fuse puller

.

4. If the fuse is open, replace it with a

new fuse. Spare fuses are stored in the

fuse box.

5. If a new fuse also opens, have the

electrical system checked and re-

paired. It is recommended you visit a

NISSAN dealer for this service.

WAI0341X

Extended storage fuse switch

To reduce battery drain, the extended

storage fuse switch comes from the

factory switched off.
Prior to delivery of your vehicle, the switch

is pushed in (switched on) and should

always remain on.
If the extended storage fuse switch is not

pushed in (switched on), the “Shipping

Mode On, Push Storage Fuse” warning

may appear on the vehicle information

display. See “22. Shipping Mode On Push

Storage Fuse warning” (P.2-34).
If any electrical equipment does not

operate, remove the extended storage

-------------------------------------------------------------------------------------------------------------------------------------------------------------

fuse switch and check for an open fuse.

NOTE:
If the extended storage fuse switch

malfunctions, or if the fuse is open, it

is not necessary to replace the switch.

In this case, remove the extended sto-

rage fuse switch and replace it with a

new fuse of the same rating.
How to remove the extended storage
fuse switch:

1. To remove the extended storage fuse

switch, be sure the ignition switch is in

the OFF or LOCK position.

2. Be sure the headlights are off. (See

“Headlight switch” (P.2-46) or “Auto-

light system” (P.2-47).)

3. Remove the fuse box cover.
4. Pinch the locking tabs

found on

each side of the storage fuse switch.

5. Pull the storage fuse switch straight

out from the fuse box

.

JVM0317X

CAUTION

Be careful not to allow children to

swallow the battery and removed

parts.

Replace the battery as follows:
1. Remove the mechanical key from the

key.

2. Insert a small screwdriver into the slit

of the corner and twist it to separate

the upper part from the lower part.

Use a cloth to protect the casing.

3. Replace the battery with a new one.

Recommended battery:
CR2032 or equivalent

.

Do not touch the internal circuit

and electric terminals as doing so

could cause a malfunction.

.

Hold the battery by the edges.

Holding the battery across the

contact points will seriously deplete

the storage capacity.

.

Make sure that the

+

side faces the

bottom case.

Do-it-yourself

8-21

INTELLIGENT KEY BATTERY REPLACEMENT

-------------------------------------------------------------------------------------------------------------------------------------------------------------

8-22

Do-it-yourself

SDI2452

4. Align the tips of the upper and lower

parts , and then push them together

until it is securely closed

.

5. Operate the buttons to check its

operation.

If you need any assistance for replace-

ment, it is recommended you visit a

NISSAN dealer for this service.

FCC Notice:
For USA:
FCC ID: KR5TXN7
This device complies with Part 15 of the

FCC Rules. Operation is subject to the

following two conditions: (1) This device

may not cause harmful interference,

and (2) this device must accept any

interference received, including inter-

ference that may cause undesired op-

eration.
Changes or modifications not expressly

approved by the party responsible for

compliance could void the user’s

authority to operate the equipment.
This equipment complies with FCC ra-

diation exposure limits set forth for

portable use conditions.
For Canada:
This device complies with Industry Ca-

nada licence-exempt RSS standard(s).

Operation is subject to the following

two conditions: (1) this device may not

cause interference, and (2) this device

must accept any interference, including

interference that may cause undesired

operation of the device.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

WAI0338X

1.

Headlight (high- and low-beam)

2.

Front turn signal light

3.

Map light

4.

Side turn signal light

5.

Daytime running/front parking light

6.

Front side marker light

7.

High-mounted stop light

8.

License plate light

9.

Cargo light

10.

Rear combination light (rear turn signal/

tail/stop/rear fog (if so equipped)/back-

up light)

11.

Rear side marker light

HEADLIGHTS

Fog may temporarily form inside the lens

of the exterior lights in the rain or in a car

wash. A temperature difference between

the inside and the outside of the lens

causes the fog. This is not a malfunction.

If large drops of water collect inside the

lens, it is recommended you visit a NISSAN

dealer for this service.

Replacing

If LED headlight replacement is required,

it is recommended that you visit a NISSAN

dealer for this service.

Do-it-yourself

8-23

LIGHTS

-------------------------------------------------------------------------------------------------------------------------------------------------------------

8-24

Do-it-yourself

EXTERIOR AND INTERIOR LIGHTS

Item

Wattage (W)

Bulb No.

Headlight*

LED

Front turn signal light*

LED

Front parking light*

LED

Front side marker light*

LED

Side turn signal light*

LED

Daytime running light*

LED

Rear combination light*

back-up

LED

turn signal

LED

stop/tail/rear fog (if so equipped)

LED

Rear side marker light*

LED

License plate light*

LED

Map light

8

Vanity mirror light*

1.8

Cargo light*

5

High-mounted stop light*

LED

Glove box light*

1.4

*:

It is recommended you visit a NISSAN dealer for replacement.

NOTE: Always check with the Parts Department at a NISSAN dealer for the latest information

about parts.

Replacement procedures

All other lights are either type A, B, C, D, E

or F. When replacing a bulb, first remove

the lens and/or cover.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

SDI1679

SDI2352

Map light

Do-it-yourself

8-25

-------------------------------------------------------------------------------------------------------------------------------------------------------------

8-26

Do-it-yourself

If you have a flat tire, see “Flat tire” (P.6-

3).

TIRE PRESSURE
Tire Pressure Monitoring System

(TPMS)

This vehicle is equipped with the Tire

Pressure Monitoring System (TPMS). It

monitors tire pressure of all tires. When

the low tire pressure warning light is lit

and the “Tire Pressure Low - Add Air”

warning message is displayed in the

vehicle information display, one or more

of your tires is significantly under-inflated.
The TPMS will activate only when the

vehicle is driven at speeds above 16 MPH

(25 km/h). Also, this system may not

detect a sudden drop in tire pressure

(for example a flat tire while driving).
For more details, see “Low tire pressure

warning light” (P.2-18), “Tire Pressure Mon-

itoring System (TPMS)” (P.5-5) and “Tire

Pressure Monitoring System (TPMS)” (P.6-

3).

Tire inflation pressure
Check the pressure of the tires

often and always prior to long

distance trips. The recommended

tire pressure specifications are

shown on the Tire and Loading

Information label under the “Cold

Tire Pressure” heading. The Tire

and Loading Information label is

affixed to the driver side center

pillar. Tire pressures should be

checked regularly because:

.

Most tires naturally lose air over

time.

.

Tires can lose air suddenly when

driven over potholes or other

objects or if the vehicle strikes

a curb while parking.

The tire pressures should be

checked when the tires are cold.

The tires are considered COLD after

the vehicle has been parked for 3 or

more hours, or driven less than 1

mile (1.6 km) at moderate speeds.
TPMS with Easy Fill Tire Alert pro-

vides visual and audible signals

outside the vehicle for inflating the

tires to the recommended COLD

tire pressure. (See “TPMS with Easy

Fill Tire Alert” (P.5-8).)

Incorrect tire pressure, including

under inflation, may adversely

affect tire life and vehicle hand-

ling.

WARNING

.

Improperly inflated tires can

fail suddenly and cause an

accident.

.

The Gross Vehicle Weight

rating (GVWR) is located on

the F.M.V.S.S./C.M.V.S.S. la-

bel. The vehicle weight ca-

pacity is indicated on the

Tire and Loading Informa-

tion label. Do not load your

vehicle beyond this capacity.

Overloading your vehicle

may result in reduced tire

life, unsafe operating condi-

tions due to premature tire

failure, or unfavorable hand-

ling characteristics and

WHEELS AND TIRES

-------------------------------------------------------------------------------------------------------------------------------------------------------------

could also lead to a serious

accident. Loading beyond

the specified capacity may

also result in failure of other

vehicle components.

.

Before taking a long trip, or

whenever you heavily load

your vehicle, use a tire pres-

sure gauge to ensure that

the tire pressures are at the

specified level.

.

For additional information

regarding tires, refer to “Im-

portant Tire Safety Informa-

tion” (US) or “Tire Safety

Information” (Canada) in the

Warranty Information Book-

let.

Do-it-yourself

8-27

-------------------------------------------------------------------------------------------------------------------------------------------------------------

8-28

Do-it-yourself

SDI2462

Tire and Loading Information label

Seating capacity: The max-

imum number of occu-

pants that can be seated

in the vehicle.
Vehicle load limit: See “Ve-

hicle loading information”

(P.10-17).
Original size: The size of

the tires originally installed

on the vehicle at the fac-

tory.

Cold tire pressure: Inflate

the tires to this pressure

when the tires are cold.

Tires are considered COLD

after the vehicle has been

parked for 3 or more hours,

or driven less than 1 mile

( 1 . 6 k m ) a t m o d e r a t e

speeds. The recommended

cold tire inflation is set by

the manufacturer to pro-

vide the best balance of

tire wear, vehicle handling,

driveability, tire noise, etc.,

up to the vehicle’s GVWR.
Tire size — see “Tire label-

ing” (P.8-30).
Spare tire size or compact

s p a r e t i r e s i z e ( i f s o

equipped)

-------------------------------------------------------------------------------------------------------------------------------------------------------------

SDI1949

Checking the tire pressure
1. Remove the valve stem cap from

the tire.

2. Press the pressure gauge

squarely onto the valve stem.

Do not press too hard or force

the valve stem sideways, or air

will escape. If the hissing sound

of air escaping from the tire is

heard while checking the pres-

sure, reposition the gauge to

eliminate this leakage.

3. Remove the gauge.
4. Read the tire pressure on the

gauge stem and compare it to

the specification shown on the

Tire and Loading Information

label.

5. Add air to the tire as needed. If

too much air is added, press the

core of the valve stem briefly

with the tip of the gauge stem to

release pressure. Recheck the

pressure and add or release air

as needed.

6. Install the valve stem cap.
7. Check the pressure of all other

tires.

Size

Cold Tire Inflation

Pressure

psi

kPa

Front Origi-

nal Tire:

245/45R18

96W

33

230

Front Origi-

nal Tire:

255/40R19

96W

32

220

Rear Original

Tire:

245/45R18

96W

33

230

Rear Original

Tire:

275/35R19

96W

29

200

Do-it-yourself

8-29

-------------------------------------------------------------------------------------------------------------------------------------------------------------

8-30

Do-it-yourself

SDI1575

Example

TIRE LABELING
Federal law requires tire manufac-

turers to place standardized infor-

mation on the sidewall of all tires.

This information identifies and de-

scribes the fundamental character-

istics of the tire and also provides

the tire identification number (TIN)

for safety standard certification.

The TIN can be used to identify

the tire in case of a recall.

SDI1606

Example

T i r e

s i z e

( e x a m p l e :

P215/60R16 94H)

1. P: The “P” indicates the tire is

designed for passenger vehicles.

(Not all tires have this informa-

tion.)

2. Three-digit number (215): This

number gives the width in milli-

meters of the tire from sidewall

edge to sidewall edge.

3. Two-digit number (60): This

number, known as the aspect

ratio, gives the tire’s ratio of

height to width.

4. R: The “R” stands for radial.
5. Two-digit number (16): This

number is the wheel or rim

diameter in inches.

6. Two- or three-digit number (94):

This number is the tire’s load

index. It is a measurement of

how much weight each tire can

support. You may not find this

information on all tires because

it is not required by law.

7. H: Tire speed rating. You should

not drive the vehicle faster than

the tire speed rating.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

JVM0694X

Example (Type A) (if so equipped)

TIN (Tire Identification

Number) for a new tire

(example: DOT XX XX XXX

XXXX)

1. DOT: Abbreviation for the “De-

partment of Transportation”.

The symbol can be placed

above, below or to the left or

right of the Tire Identification

Number.

2. Two-digit code: Manufacturer’s

identification mark

3. Two-digit code: Tire size
4. Three-digit code: Tire type code

(Optional)

5. Four numbers represent the

week and year the tire was built.

For example, the numbers 3103

means the 31st week of 2003. If

these numbers are missing, then

look on the other sidewall of the

tire.

WAI0339X

Example (Type B) (if so equipped)

TIN (Tire Identification

Number) for a new tire

(example: DOT XXX XXXXXX

XXXX)

1. DOT: Abbreviation for the “De-

partment of Transportation”.

The symbol can be placed

above, below or to the left or

right of the Tire Identification

Number.

2. Three-digit code: Manufacturer’s

identification mark

Do-it-yourself

8-31

-------------------------------------------------------------------------------------------------------------------------------------------------------------

8-32

Do-it-yourself

3. Six-digit code: Descriptive code

used to identify significant char-

acteristics of the tire.

4. Four numbers represent the

week and year the tire was built.

For example, the numbers 3103

means the 31st week of 2003.

Tire ply composition and

material
The number of layers or

plies of rubber-coated fab-

ric in the tire.
Tire manufacturers also

must indicate the materials

in the tire, which include

steel, nylon, polyester, and

others.
Maximum permissible infla-

tion pressure
This number is the greatest

amount of air pressure

that should be put in the

tire. Do not exceed the

maximum permissible in-

flation pressure.
Maximum load rating

This number indicates the

maximum load in kilo-

grams and pounds that

can be carried by the tire.

When replacing the tires on

the vehicle, always use a

tire that has the same load

rating as the factory in-

stalled tire.
Term of “tubeless” or “tube

type”
Indicates whether the tire

requires an inner tube

(“tube type”) or not (“tube-

less”).
The word “radial”
The word “radial” is shown,

if the tire has radial struc-

ture.
Manufacturer or brand

name
Manufacturer or brand

name is shown.

Other tire-related terminology:

In addition to the many terms that

are defined throughout this sec-

tion, Intended Outboard Sidewall is

(1) the sidewall that contains a

whitewall, bears white lettering or

bears manufacturer, brand and/or

model name molding that is higher

or deeper than the same molding

on the other sidewall of the tire, or

(2) the outward facing sidewall of

an asymmetrical tire that has a

particular side that must always

face outward when mounted on a

vehicle.
TYPES OF TIRES

WARNING

.

When changing or replacing tires,

be sure all four tires are of the

same type (Example: Summer, All

Season or Snow) and construc-

tion. A NISSAN dealer may be able

to help you with information

about tire type, size, speed rating

and availability.

.

Replacement tires may have a

lower speed rating than the fac-

tory equipped tires, and may not

match the potential maximum

vehicle speed. Never exceed the

-------------------------------------------------------------------------------------------------------------------------------------------------------------

maximum speed rating of the

tire.

.

Replacing tires with those not

originally specified by NISSAN

could affect the proper operation

of the TPMS.

.

For additional information re-

garding tires, refer to “Important

Tire Safety Information” (US) or

“Tire Safety Information” (Cana-

da) in the Warranty Information

Booklet.

All season tires

NISSAN specifies all season tires on some

models to provide good performance all

year, including snowy and icy road con-

ditions. All Season tires are identified by

ALL SEASON and/or M&S (Mud and Snow)

on the tire sidewall. Snow tires have

better snow traction than All Season tires

and may be more appropriate in some

areas.

Summer tires

NISSAN specifies summer tires on some

models to provide superior performance

on dry roads. Summer tire performance is

substantially reduced in snow and ice.

Summer tires do not have the tire trac-

tion rating M&S on the tire sidewall.

If you plan to operate your vehicle in

snowy or icy conditions, NISSAN recom-

mends the use of SNOW tires or ALL

SEASON tires on all four wheels.

Snow tires

If snow tires are needed, it is necessary to

select tires equivalent in size and load

rating to the original equipment tires. If

you do not, it can adversely affect the

safety and handling of your vehicle.
Generally, snow tires will have lower

speed ratings than factory equipped tires

and may not match the potential max-

imum vehicle speed. Never exceed the

maximum speed rating of the tire.
If you install snow tires, they must be the

same brand, construction and tread pat-

tern on all four wheels, and the same

sizes as the original tires.
For additional traction on icy roads,

studded tires may be used. However,

some U.S. states and Canadian provinces

prohibit their use. Check local, state and

provincial laws before installing studded

tires. Skid and traction capabilities of

studded snow tires, on wet or dry sur-

faces, may be poorer than that of non-

studded snow tires.

TIRE CHAINS

CAUTION

Tire chains/cables should not be

installed on 19-inch size tires. Doing

so will cause damage to the vehicle.

Use of tire chains may be prohibited

according to location. Check the local

laws before installing tire chains. When

installing tire chains, make sure they are

the proper size for the tires on your

vehicle and are installed according to

the chain manufacturer’s suggestions.

Use only SAE Class S chains.

Class “S”

chains are used on vehicles with re-

stricted tire to vehicle clearance. Vehicles

that can use Class “S” chains are designed

to meet the SAE standard minimum

clearances between the tire and the

closest vehicle suspension or body com-

ponent required to accommodate the

use of a winter traction device (tire chains

or cables). The minimum clearances are

determined using the factory equipped

tire size. Other types may damage your

vehicle. Use chain tensioners when re-

commended by the tire chain manufac-

turer to ensure a tight fit. Loose end links

of the tire chain must be secured or

removed to prevent the possibility of

Do-it-yourself

8-33

-------------------------------------------------------------------------------------------------------------------------------------------------------------

8-34

Do-it-yourself

whipping action damage to the fenders

or underbody. If possible, avoid fully load-

ing your vehicle when using tire chains. In

addition, drive at a reduced speed. Other-

wise, your vehicle may be damaged and/

or vehicle handling and performance may

be adversely affected.

Tire chains must be installed only on

the rear wheels and not on the front

wheels.

Do not use tire chains on dry roads.

Driving with tire chains in such conditions

can cause damage to the various me-

chanisms of the vehicle due to some

overstress.

CHANGING WHEELS AND TIRES
Tire rotation
Tires cannot be rotated on this

vehicle because the front tires are

a different size and/or wheel rim

offset than the rear tires.

WARNING

.

Retighten the wheel nuts

when the vehicle has been

driven for 600 miles (1,000

km) (also in cases of a flat

tire, etc.).

.

For additional information

regarding tires, refer to “Im-

portant Tire Safety Informa-

tion” (US) or “Tire Safety

Information” (Canada) in the

Warranty Information Book-

let.

SDI1663

Wear indicator
Wear indicator location

marks. The locations are

shown by “

”, “TWI”, etc.

depending on tire types.

Tire wear and damage

WARNING

.

Tires should be periodically

inspected for wear, cracking,

bulging or objects caught in

the tread. If excessive wear,

-------------------------------------------------------------------------------------------------------------------------------------------------------------

 

 

 

 

 

 

 

Content      ..     19      20      21      22     ..