Nissan Z (2023 year). Manual in english - page 8

 

  Index      Manuals     Nissan Z (2023 year). Manual in english

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

 

 

 

Content      ..     6      7      8      9     ..

 

 

 

Nissan Z (2023 year). Manual in english - page 8

 

 

The power outlet is located in the center

console and on the lower glove box.

CAUTION

.

The outlet and plug may be hot

during or immediately after use.

.

Do not use with accessories that

exceed a 12 volt, 120W (10A)

power draw. Do not use double

adapters or more than one elec-

trical accessory.

.

Use power outlet with the engine

running to avoid discharging the

vehicle battery.

.

Avoid using power outlet when

the air conditioner, headlights or

rear window defroster is on.

.

This power outlet is not designed

for use with a cigarette lighter

unit.

.

Push the plug in as far as it will

go. If good contact is not made,

the plug may overheat or the

internal temperature fuse may

blow.

.

Before inserting or disconnecting

a plug, be sure the electrical

accessory being used is turned

OFF.

.

When not in use, be sure to close

the cap. Do not allow water or any

liquid to contact the outlet.

WAC0897X

Type C USB charging connector
Type A USB charging connector

USB (Universal Serial Bus) CHAR-

GING CONNECTOR

The USB charging connector is located on

the front of the center console.
The USB charging connector can be used

for charging an external device.
Connect a USB device into the connector.

Charging will start automatically (max-

imum output up to 5volt, 12W, 2.4A (Type-

A) and 5volt, 15W, 3A (Type-C)).
The external device will be charged con-

tinuously while the ignition switch is in

the ON position.

Instruments and controls

2-57

-------------------------------------------------------------------------------------------------------------------------------------------------------------

2-58

Instruments and controls

Some mobile devices cannot be charged

depending on their specifications.

CAUTION

.

Do not force a USB device into the

connector. Depending on the USB

connector, inserting the USB de-

vice tilted or upside down may

damage the connector. Make

sure that the USB device is con-

nected correctly into the connec-

tor.

.

Do not use a reversible USB cable.

Using the reversible USB cable

may damage the connector.

NOTE:
For best results, it is recommended that

you use manufacturer-branded cables,

or USB adapter, which may be sold

separately. See your device’s owner’s

information for more details.

EMERGENCY SUPPORT

NissanConnect® Services provide various

services to support dealing with emer-

gencies of the subscribed vehicle and the

driver.
For example, in case of an illness or

serious injury, you can seek support by

pushing the in-vehicle Emergency Call

(SOS) button and connecting to the

NissanConnect® Services Response Cen-

ter. The NissanConnect® Services Re-

sponse Center can specify the location

of the vehicle via GPS, and the informa-

tion will be sent to the police or other

agencies as needed.
For information about other NissanCon-

nect® Services emergency support re-

l a t e d

s e r v i c e s ,

c o n t a c t

t h e

NissanConnect® Customer Support line

at 1-855-426-6628 or refer to the Nissan-

Connect® Services website www.nissanu-

sa.com/connect (for U.S.) or www.nissan.

ca/nissanconnect (English)/www.nissan.

ca/nissanconnect/fr (French) (for Cana-

da).

WARNING

.

Please note that the Automatic

Collision Notification service and

Emergency Call function cannot

be used in the following condi-

tions:
— Emergency functions and ser-

vices will not be available

without a paid subscription

to NissanConnect® Services.

— The NissanConnect® Services

network system is disabled.

— The vehicle moves outside the

service area where the TCU

(Telematics Control Unit) is

connected to the system.

— The vehicle is outside the area

where the cellular network

service is receivable.

— The vehicle is in a location

with poor signal reception

such as tunnels, underground

parking garages, behind

buildings or in mountainous

areas.

— The line is busy.
— The TCU (Telematics Control

Unit) or other systems of your

vehicle are not working prop-

erly.

— It may not be possible to

make an emergency call de-

pending on the severity of a

EMERGENCY CALL (SOS) BUTTON

(if so equipped)

-------------------------------------------------------------------------------------------------------------------------------------------------------------

collision and/or emergency.

.

Park the vehicle in a safe location

and set the parking brake before

operating the Emergency Call

(SOS) button.

.

Only use this service in case of an

emergency. There may be a pen-

alty for inappropriate use of the

service.

.

Radio waves could adversely af-

fect electric medical equipment.

Individuals who use a pacemaker

should contact the device manu-

facturer regarding any possible

effects before using the system.

.

The TCU (Telematics Control Unit)

antenna is installed inside the

upper central part of the instru-

ment panel. An occupant should

not get any closer to the antenna

than specified by the pacemaker

manufacturer. The radio waves

from the TCU antenna may ad-

versely affect the operation of the

pacemaker while using the Nis-

sanConnect® Services.

WAC0914X

Making an emergency call

The Emergency Call (SOS) button is lo-

cated near the map light.
1. Push the cover to expose the Emer-

gency Call (SOS) button

.

2. Push the Emergency Call (SOS) button

to make an emergency call.

3. When the line is connected, speak to

the Response Specialist.

If you want to cancel the emergency call,

push and hold the Emergency Call (SOS)

button for a few seconds.

NOTE:

.

After the Emergency Call (SOS) but-

ton is pushed, it may take some time

until the system initiates connec-

tion, depending on the technical

environment and whether the TCU

(Telematics Control Unit) is being

used by other services.

.

An indicator light on the Emergency

Call (SOS) button shows the readi-

ness of the emergency support sys-

tem. If the indicator light is not

illuminated, pushing the Emergency

Call (SOS) button does not connect

your vehicle to the Response Spe-

cialist.
The indicator light blinks while con-

nected to the NissanConnect® Ser-

vices Response Center.

.

Even when the indicator light is

illuminated, connection to the Nis-

sanConnect® Services Response

Center may not be possible. If this

occurs in an emergency situation,

contact the authorities by other

means.

.

To avoid disconnecting the line,

keep the engine running during an

emergency call, if it is safe to do so.

Instruments and controls

2-59

-------------------------------------------------------------------------------------------------------------------------------------------------------------

2-60

Instruments and controls

CUP HOLDERS

CAUTION

.

Avoid abrupt starting and braking

when the cup holder is being

used to prevent spilling the drink.

If the liquid is hot, it can scald you

or your passenger.

.

Use only soft cups in the cup

holder. Hard objects can injure

you in an accident.

WAC0904X

The cup holders are located on the center

console.

SIC3988

Soft bottle holder

CAUTION

.

Do not use bottle holder for any

other objects that could be

thrown about in the vehicle and

possibly injure people during

sudden braking or an accident.

.

Do not use bottle holder for open

liquid containers.

STORAGE

-------------------------------------------------------------------------------------------------------------------------------------------------------------

SIC3999

GLOVE BOX

WARNING

Keep glove box lid closed while driv-

ing to help prevent injury in an

accident or a sudden stop.

To open the glove box, pull the handle

.

To close, push the lid in until the lock

latches.
To lock /unlock

the glove box, use the

mechanical key. For the mechanical key

usage, see “Keys” (P.3-2).

WAC0901X

WAC0902X

WAC0903X

CONSOLE BOX

To open the console box, push the button

and pull up the lid.

To close, push the lid down until latched.
The position of the console lid can be

adjusted to your desired position. Slide

the lid to forward or backward to the

desired position.
The slide function can be locked when the

lid is in maximum forward by tightening

the screw

in the

position. When not

using the lock function, tighten the screw

in the

position.

Instruments and controls

2-61

-------------------------------------------------------------------------------------------------------------------------------------------------------------

2-62

Instruments and controls

SIC3989

REAR PARCEL BOX

The rear parcel box is located behind the

right-side seat.
To open the rear parcel box, pull the

upper part of the lid to position

or

.

To remove the rear parcel box, pull the lid

to position

with a greater force until it

unlatches. And then, pull the rear parcel

box to direction

.

To install, make sure the two hinges of

the rear parcel box engaged with the

holders, then perform the steps above in

the reverse order.

WARNING

Keep the rear parcel box lid closed

while driving to help prevent injury in

an accident or a sudden stop.

WAC0998X

REAR HATCH HOOKS

WARNING

.

Always make sure that the cargo

is properly secured. Use the sui-

table ropes and hooks.

.

Unsecured cargo can become

dangerous in an accident or sud-

den stop.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

CAUTION

Do not apply a total load of more

than 22 lb (10 kg) to a single hook.

POWER WINDOWS

WARNING

.

Make sure that all passengers

have their hands, etc. inside the

vehicle while it is in motion and

before closing the windows. Use

the window lock switch to pre-

vent unexpected use of the

power windows.

.

To help avoid risk of injury or

death through unintended opera-

tion of the vehicle and or its

systems, including entrapment

in windows or inadvertent door

lock activation, do not leave chil-

dren, people who require the

assistance of others or pets un-

attended in your vehicle. Addi-

tionally, the temperature inside a

closed vehicle on a warm day can

quickly become high enough to

cause a significant risk of injury

or death to people and pets.

The power windows operate when the

ignition switch is in the ON position or for

about 45 seconds after the ignition

switch is pushed to the OFF position. If

the driver’s or front passenger’s door is

opened during this period of about 45

seconds, power to the windows is can-

celed.

Instruments and controls

2-63

WINDOWS

-------------------------------------------------------------------------------------------------------------------------------------------------------------

2-64

Instruments and controls

JVI1248X

1.

Driver side window

2.

Front passenger side window

3.

Window lock button

Main power window switch (driver’s

side)

To open or close the window, push down

or pull up

the switch and hold it. The

main switch (driver side switches) will

open or close all the windows.

Locking passenger’s window

When the lock button

is pushed in, only

the driver side window can be opened or

closed. Push it in again to cancel.

SIC3241

Passenger side power window

switch

The passenger side switch will open or

close only the corresponding window. To

open or close the window, push down or

pull up the switch and hold it.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

JVI1203X

Automatic operation

To fully open or close the window, com-

pletely push down or pull up the switch

and release it; it need not be held. The

window will automatically open or close

all the way. To stop the window, just push

or lift the switch in the opposite direction.
A light push or pull on the switch will

cause the window to open or close until

the switch is released.

Operating windows with Intelligent

Key

The windows can be opened by pushing

the UNLOCK

button on the Intelligent

Key. This function will not operate while

the window timer is activated or when

the windows need to be initialized. For

details about the Intelligent Key button

usage, see “How to use remote keyless

entry system” (P.3-12).

Opening:

To open the windows, push the UNLOCK

button on the Intelligent Key for

about 3 seconds after the door is un-

locked.
To stop opening, release the UNLOCK

button.
If the window open operation is stopped

on the way while pushing the UNLOCK

button, release and push the button

again until the windows open completely.

Auto reverse function

WARNING

There are some small distances im-

mediately before the closed position

which cannot be detected. Make sure

that all passengers have their hands,

etc., inside the vehicle before closing

the window.

If the control unit detects something

caught in the window as it is closing, the

window will be immediately lowered.
The auto reverse function can be acti-

vated when the window is closed by

automatic operation when the ignition

switch is in the ON position or for 45

seconds after the ignition switch is

pushed to the OFF position.

Depending on the environment or driv-

ing conditions, the auto reverse func-

tion may be activated if an impact or

load similar to something being caught

in the window occurs.

Automatic adjusting function

CAUTION

When the battery cable is removed

from the battery terminal, do not

close either of the front doors. The

automatic window adjusting func-

tion will not work and the side roof

panel may be damaged.

The power window has an automatic

adjusting function. When the door is

Instruments and controls

2-65

-------------------------------------------------------------------------------------------------------------------------------------------------------------

2-66

Instruments and controls

being opened, the window is automati-

cally lowered slightly to avoid contact

between the window and the side roof

panel. When the door is closed, the

window is automatically raised slightly.
While the automatic adjusting function

does not work, the window will be con-

trolled as follows:

.

When the door is opened, the window

lowers for approximately 0.15 seconds.

.

While the door is open, the window

cannot be raised.

If the windows do not close auto-

matically

If the power window automatic function

(closing only) does not operate properly,

perform the following procedure to initi-

alize the power window system.
1. Push the ignition switch to start the

engine.

2. Close the door.
3. After starting the engine, open the

window completely by operating the

power window switch.

4. Pull the power window switch and

hold it to close the window, and then

hold the switch more than 3 seconds

after the window is closed completely.

5. Release the power window switch.

Operate the window by the automatic

function to confirm the initialization is

complete.

6. Perform steps 2 through 5 above for

other windows.

If the power window automatic function

does not operate properly after perform-

ing the procedure above, have your

vehicle checked. It is recommended you

visit a NISSAN dealer for this service.

SIC4238

MAP LIGHTS

Push the button as illustrated to turn the

light on or off.

INTERIOR LIGHTS

-------------------------------------------------------------------------------------------------------------------------------------------------------------

SIC4239

INTERIOR LIGHT CONTROL SWITCH

The interior light control switch has three

positions: ON, DOOR and OFF.

ON position

When the switch is in the ON position

the map lights will illuminate.

DOOR position

When the switch is in the DOOR position

, the map lights will illuminate under the

following conditions:

.

ignition switch is switched to the OFF

or LOCK position
— remain on for about 15 seconds.

.

doors are unlocked by pushing the

UNLOCK button on the Intelligent Key

or door handle request switch with

the ignition switch in the LOCK posi-

tion
— remain on for about 15 seconds.

.

any door is opened and then closed

with the ignition switch in the LOCK

position
— remain on for about 15 seconds.

.

any door is opened with the ignition

switch in the ACC or ON position
— remain on while the door is opened.

When the door is closed, the lights

go off.

The lights will also turn off after a

period of time when the lights remain

illuminated after the ignition switch has

been pushed to the OFF or LOCK posi-

tion to prevent the battery from becom-

ing discharged.

When the “Auto Room Lamp” is set to the

OFF position (see “Vehicle Settings” (P.2-

25)), the lights will illuminate under the

following condition:

.

any door is opened with the ignition

switch in any position
— remain on while the door is opened.

When the door is closed, the lights

go off.

OFF position

When the switch is in the OFF position

,

the lights will not illuminate, regardless of

the condition.

CAUTION

Do not use for extended periods of

time with the engine stopped. This

could result in a discharged battery.

Instruments and controls

2-67

-------------------------------------------------------------------------------------------------------------------------------------------------------------

2-68

Instruments and controls

SIC3869

The light on the vanity mirror will turn on

when the cover on the vanity mirror is

opened.
When the cover is closed, the light will

turn off.

The lights will also turn off after a

period of time when the lights remain

illuminated to prevent the battery from

becoming discharged.

The light illuminates when the rear hatch

is opened. When the rear hatch is closed,

the light will turn off.

The light will also turn off after a period

of time when the light remains illumi-

nated after the ignition switch has been

pushed to the OFF or LOCK position to

prevent the battery from becoming

discharged.

The HomeLink® Universal Transceiver

provides a convenient way to consolidate

the functions of up to three individual

hand-held transmitters into one built-in

device.
HomeLink® Universal Transceiver:

.

Will operate most Radio Frequency

(RF) devices such as garage doors,

gates, home and office lighting, entry

door locks and security systems.

.

Is powered by your vehicle’s battery.

No separate batteries are required. If

the vehicle’s battery is discharged or is

disconnected, HomeLink® will retain

all programming.

When the HomeLink® Universal Trans-

ceiver is programmed, retain the origi-

nal transmitter for future programming

procedures (Example: new vehicle pur-

chases). Upon sale of the vehicle, the

programmed HomeLink® Universal

Transceiver buttons should be erased

for security purposes. For additional

information, refer to “Programming

HomeLink®” (P.2-69).

WARNING

.

Do not use the HomeLink® Uni-

versal Transceiver with any gar-

age door opener that lacks safety

VANITY MIRROR LIGHTS

CARGO LIGHT

HomeLink® UNIVERSAL

TRANSCEIVER (if so equipped)

-------------------------------------------------------------------------------------------------------------------------------------------------------------

stop and reverse features as re-

quired by federal safety stan-

dards. (These standards became

effective for opener models man-

ufactured after April 1, 1982). A

garage door opener which cannot

detect an object in the path of a

closing garage door and then

automatically stop and reverse,

does not meet current federal

safety standards. Using a garage

door opener without these fea-

tures increases the risk of serious

injury or death.

.

During the programming proce-

dure your garage door or security

gate will open and close (if the

transmitter is within range). Make

sure that people or objects are

clear of the garage door, gate,

etc. that you are programming.

.

Your vehicle’s engine should be

turned off while programming

the HomeLink® Universal Trans-

ceiver. Do not breathe exhaust

gases; they contain colorless

and odorless carbon monoxide.

Carbon monoxide is dangerous. It

can cause unconsciousness or

death.

PROGRAMMING HomeLink®

If you have any questions or are having

difficulty programming your HomeLink®

buttons, refer to the HomeLink® web site

at: www.homelink.com or call 1-800-355-

3515.

NOTE:
Place the ignition switch in the ON

position (without starting the engine)

when programming HomeLink®. It is

also recommended that a new battery

be placed in the hand-held transmitter

of the device being programmed to

HomeLink® for quicker programming

and accurate transmission of the

radio-frequency.

1. Position the end of your hand-held

transmitter 1-3 in (26-76 mm) away

from the HomeLink® surface, keeping

the HomeLink® indicator light

in

view.

JVI0428X

2. Using both hands, simultaneously

press and hold the desired HomeLink®

button and handheld transmitter but-

ton. DO NOT release until the

HomeLink® indicator light

flashes

slowly and then rapidly. When the

indicator light flashes rapidly, both

buttons may be released. (The rapid

flashing indicates successful pro-

gramming.)

NOTE:

Some devices to be programmed

may require you to replace Step 2

with the cycling procedure noted in

the “Programming HomeLink® for

Canadian customers and gate open-

ers” (P.2-70).

Instruments and controls

2-69

-------------------------------------------------------------------------------------------------------------------------------------------------------------

2-70

Instruments and controls

JVI0429X

3. Press and hold the programmed

HomeLink® button and observe the

indicator light.

.

If the indicator light

is solid/

continuous, programming is com-

plete and your device should acti-

vate when the HomeLink® button is

pressed and released.

.

If the indicator light

blinks rapidly

for two seconds and then turns to a

solid/continuous light, continue

with Steps 4-6 for a rolling code

device. A second person may make

the following steps easier. Use a

ladder or other device. Do not stand

on your vehicle to perform the next

steps.

4. At the receiver located on the garage

door opener motor in the garage,

locate the “learn” or “smart” button

(the name and color of the button

may vary by manufacturer but it is

usually located near where the hang-

ing antenna wire is attached to the

unit). If there is difficulty locating the

button, reference the garage door

opener’s manual.

5. Press and release the “learn” or “smart”

button.

NOTE:

Once the button is pressed, you have

approximately 30 seconds to initiate

the next step.

6. Return to the vehicle and firmly press

and hold the programmed HomeLink®

button for two seconds and release.

Repeat the “press/hold/release” se-

quence up to 3 times to complete

the programming process. HomeLink®

should now activate your rolling code

equipped device.

7. If you have any questions or are

having difficulty programming your

HomeLink® buttons, refer to the

HomeLink® web site at: www.

homelink.com or call 1-800-355-3515.

PROGRAMMING HomeLink® FOR

CANADIAN CUSTOMERS AND GATE

OPENERS

Canadian radio-frequency laws require

transmitter signals to “time-out” (or quit)

after several seconds of transmission –

which may not be long enough for

HomeLink® to pick up the signal during

programming. Similar to this Canadian

law, some U.S. gate operators are de-

signed to “time-out” in the same manner.
If you live in Canada or you are having

difficulties programming a gate operator

or garage door opener by using the

“Programming HomeLink®” procedures,

replace “Programming HomeLink®” Step

2 with the following:

NOTE:
When programming a garage door

opener, etc., unplug the device during

the “cycling” process to prevent possi-

ble damage to the garage door opener

components.

Step 2: Using both hands, simultaneously

press and hold the desired HomeLink®

button and the hand-held transmitter

button. During programming, your hand-

held transmitter may automatically stop

transmitting. Continue to press and hold

the desired HomeLink® button while you

press and re-press (“cycle”) your hand-

-------------------------------------------------------------------------------------------------------------------------------------------------------------

held transmitter every two seconds until

the frequency signal has been learned.

The HomeLink® indicator light will flash

slowly and then rapidly after several

seconds upon successful programming.

DO NOT

release until the HomeLink®

indicator light flashes slowly and then

rapidly. When the indicator light flashes

rapidly, both buttons may be released.

The rapid flashing indicates successful

programming.
Proceed with “Programming HomeLink®”

step 3 to complete.
If the device was unplugged during the

programming procedure, remember to

plug it back in when programming is

completed.

OPERATING THE HomeLink® UNI-

VERSAL TRANSCEIVER

The HomeLink® Universal Transceiver,

after it is programmed, can be used to

activate the programmed device. To op-

erate, simply press and release the appro-

priate programmed HomeLink® Universal

Transceiver button. The amber indicator

light will illuminate while the signal is

being transmitted.
For convenience, the hand-held transmit-

ter of the device may also be used at any

time.

PROGRAMMING TROUBLESHOOT-

ING

If the HomeLink® does not quickly learn

the hand-held transmitter information:

.

replace the hand-held transmitter

batteries with new batteries.

.

position the hand-held transmitter

with its battery area facing away from

the HomeLink® surface.

.

press and hold both the HomeLink®

and hand-held transmitter buttons

without interruption.

.

position the hand-held transmitter 1-3

in (26-76 mm) away from the

HomeLink® surface. Hold the transmit-

ter in that position for up to 15

seconds. If HomeLink® is not pro-

grammed within that time, try holding

the transmitter in another position -

keeping the indicator light in view at

all times.

If you have any questions or are having

difficulty programming your HomeLink®

buttons, refer to the HomeLink® web site

at: www.homelink.com or 1-800-355-3515.

CLEARING THE PROGRAMMED IN-

FORMATION

The following procedure clears the pro-

grammed information from both buttons.

Individual buttons cannot be cleared.

However, individual buttons can be re-

programmed, see “Reprogramming a sin-

gle HomeLink® button” (P.2-71).

To clear all programming

1. Press and hold the two outer

HomeLink® buttons until the indicator

light begins to flash in approximately

10 seconds. Do not hold for longer

than 20 seconds.

2. Release both buttons.
HomeLink® is now in the programming

mode and can be programmed at any

time beginning with “Programming

HomeLink®” - Step 1.

REPROGRAMMING A SINGLE

HomeLink® BUTTON

To reprogram a HomeLink® Universal

Transceiver button, complete the follow-

ing.
1. Press and hold the desired HomeLink®

button.

DO NOT

release the button.

2. The indicator light will begin to flash

after 20 seconds. Without releasing

the HomeLink® button, proceed with

Instruments and controls

2-71

-------------------------------------------------------------------------------------------------------------------------------------------------------------

2-72

Instruments and controls

“Programming HomeLink®” - Step 1.

For questions or comments, contact

HomeLink® at: www.homelink.com or 1-

800-355-3515.
The HomeLink® Universal Transceiver

button has now been reprogrammed.

The new device can be activated by

pushing the HomeLink® button that was

just programmed. This procedure will not

affect any other programmed HomeLink®

buttons.

IF YOUR VEHICLE IS STOLEN

If your vehicle is stolen, you should

change the codes of any non-rolling code

device that has been programmed into

HomeLink®. Consult the Owner’s Manual

of each device or call the manufacturer or

retailer of those devices for additional

information.

When your vehicle is recovered, you will

need to reprogram the HomeLink® Uni-

versal Transceiver with your new trans-

mitter information.
FCC Notice:
For USA:
This device complies with Part 15 of the

FCC Rules. Operation is subject to the

following two conditions: (1) This device

may not cause harmful interference,

and (2) this device must accept any

interference received, including inter-

ference that may cause undesired op-

eration.
NOTE:
Changes or modifications not expressly

approved by the party responsible for

compliance could void the user’s

authority to operate the equipment.
For Canada:
This device complies with Industry Ca-

nada licence-exempt RSS standard(s).

Operation is subject to the following

two conditions: (1) this device may not

cause interference, and (2) this device

must accept any interference, including

interference that may cause undesired

operation of the device.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

 

 

 

 

 

 

 

Content      ..     6      7      8      9     ..