Nissan Altima (2022 year). Manual in english - page 23

 

  Index      Manuals     Nissan Altima (2022 year). Manual in english

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

 

 

 

Content      ..     21      22      23      24     ..

 

 

 

Nissan Altima (2022 year). Manual in english - page 23

 

 

SYSTEM MAINTENANCE

The two radar sensors

O

1

for the BSW and

RCTA systems are located near the rear
bumper. Always keep the area near the ra-
dar sensors clean.

The radar sensors may be blocked by tem-
porary ambient conditions such as splash-
ing water, mist or fog.

The blocked condition may also be caused
by objects such as ice, frost or dirt ob-
structing the radar sensors.

Check for and remove objects obstructing
the area around the radar sensors.

Do not attach stickers (including transpar-
ent material), install accessories or apply
additional paint near the radar sensors.

Do not strike or damage the area around
the radar sensors. It is recommended that
you visit a NISSAN dealer if the area around
the radar sensors is damaged due to a
collision.

Radio frequency statement

NOTICE:

This device complies with Part 15 of the FCC
Rules.

Operation is subject to the following two
conditions:

this device may not cause harmful interfer-
ence, and

this device must accept any interference
received, including interference that may
cause undesired operation.

Changes or modifications made to this
equipment not expressly approved by
(manufacturer name) may void the FCC
authorization to operate this equipment.

NOTE:

This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are de-
signed to provide reasonable protection
against harmful interference in a resi-
dential installation. This equipment gen-
erates, uses and can radiate radio fre-
quency energy and, if not installed and
used in accordance with the instruc-
tions, may cause harmful interference to
radio communications. However, there is
no guarantee that interference will not
occur in a particular installation. If this
equipment does cause harmful interfer-
ence to radio or television reception,
which can be determined by turning the
equipment off and on, the user is en-
couraged to try to correct the interfer-
ence by one or more of the following
measures:

Reorient

or

relocate

the

receiving

antenna.

Increase the separation between the
equipment and receiver.

LSD3286

Starting and driving

5-67

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.

Consult the dealer or an experienced
radio/TV technician for help.

PRECAUTIONS ON CRUISE
CONTROL

1

RES+ switch

2

CANCEL switch

3

SET– switch

4

Cruise control switch

• If the cruise control system malfunc-

tions, it cancels automatically. The

indicator in the instrument panel

then blinks to warn the driver.

• If the

indicator blinks, turn the

cruise control switch off and have the
system checked. It is recommended
that you visit a NISSAN dealer for this
service.

• The

indicator may blink when the

cruise control switch is turned on
while pushing the RES+, SET–, or CAN-
CEL switch. To properly set the cruise
control system, use the following
procedures.

WARNING

Do not use the cruise control when driv-
ing under the following conditions:

When it is not possible to keep the
vehicle at a set speed.

In heavy traffic or in traffic that varies
in speed.

On winding or hilly roads.

On slippery roads (rain, snow, ice,
etc.).

In very windy areas.

Doing so could cause a loss of vehicle
control and result in an accident.

LSD3251

CRUISE CONTROL (if so equipped)

5-68

Starting and driving

-------------------------------------------------------------------------------------------------------------------------------------------------------------

CRUISE CONTROL OPERATIONS

Cruise Control Indicator

Color

Description

None

System off

White

Standby

Green

Set

Green(Blinking)

System fault

The cruise control allows driving at a speed
between 25 - 89 mph (40 - 144 km/h) with-
out keeping your foot on the accelerator
pedal.

To turn on the cruise control,

push the

cruise control switch on. The

indicator

in the instrument panel will illuminate.

To set cruising speed,

accelerate the ve-

hicle to the desired speed, push the SET–
switch and release it. Take your foot off the
accelerator pedal. Your vehicle maintains
the set speed.

To pass another vehicle,

depress the ac-

celerator pedal. When you release the
pedal, the vehicle returns to the previ-
ously set speed.

• The vehicle may not maintain the set

speed when going up or down steep hills.
If this happens, drive without the cruise
control.

To cancel the preset speed,

use one of the

following three methods:
• Push the CANCEL switch.
• Tap the brake pedal.
• Push the cruise control switch off. The

indicator in the instrument panel

goes out.

Starting and driving

5-69

-------------------------------------------------------------------------------------------------------------------------------------------------------------

The cruise control is automatically can-
celed if:
• You depress the brake pedal while push-

ing the RES+ or SET– switch. The preset
speed is deleted from memory.

• The vehicle slows down more than 8 mph

(13 km/h) below the set speed.

• You move the shift lever to N (Neutral).

To reset at a faster cruising speed,

use

one of the following three methods:
• Depress the accelerator pedal. When the

vehicle attains the desired speed, push
and release the SET– switch.

• Push and hold the RES+ switch. When the

vehicle attains the speed you desire, re-
lease the switch.

• Push and release the RES+ switch. Each

time you do this, the set speed increases
by about 1 mph (1.6 km/h).

To reset at a slower cruising speed,

use

one of the following three methods:
• Lightly tap the brake pedal. When the ve-

hicle attains the desired speed, push the
SET– switch and release it.

• Push and hold the SET– switch. Release

the switch when the vehicle slows to the
desired speed.

• Push and release the SET– switch. Each

time you do this, the set speed decreases
by about 1 mph (1.6 km/h).

To resume the preset speed,

push and

release the RES+ switch. The vehicle re-
turns to the last set cruising speed when
the vehicle speed is over 25 mph (40 km/h).

To turn off the cruise control,

use one of

the following three methods:
• Push the CANCEL switch.
• Tap the brake pedal.
• Push the cruise control switch off. The

indicator in the instrument panel

goes out.

5-70

Starting and driving

-------------------------------------------------------------------------------------------------------------------------------------------------------------

O

A

ICC switch

WARNING

Failure to follow the warnings and in-
structions for proper use of the ICC sys-
tem could result in serious injury or
death.

The ICC system is only an aid to assist
the driver and is not a collision
warning or avoidance device. It is the
driver’s responsibility to stay alert,
drive safely, and be in control of the
vehicle at all times.

Always observe posted speed limits
and do not set the speed over them.

Always drive carefully and atten-
tively when using the ICC system.
Read and understand the Owner’s
Manual thoroughly before using the
ICC system. To avoid serious injury or
death, do not rely on the system to
prevent accidents or to control the
vehicle’s speed in emergency situa-
tions. Do not use the ICC system ex-
cept in appropriate road and traffic
conditions.

LSD3864

INTELLIGENT CRUISE CONTROL (ICC)
(if so equipped)

Starting and driving

5-71

-------------------------------------------------------------------------------------------------------------------------------------------------------------

In the conventional (fixed speed)
cruise

control

mode,

a

warning

chime will not sound to warn you if
you are too close to the vehicle
ahead. Pay special attention to the
distance between your vehicle and
the vehicle ahead of you or a collision
could occur.

The ICC system maintains a selected dis-
tance from the vehicle in front of you within
the speed range of 0 to 90 mph (0 to 144
km/h) up to the set speed. The set speed
can be selected by the driver between 0 to
90 mph (30 to 144 km/h).

The vehicle travels at a set speed when the
road ahead is clear.

The ICC system can be set to one of two
cruise control modes:

Vehicle-to-vehicle

distance

control

mode:

For maintaining a selected dis-

tance between your vehicle and the ve-
hicle in front of you up to the preset speed

Conventional (fixed speed) cruise con-
trol mode:

For cruising at a preset speed

Push the ICC switch

O

A

to choose the

cruise control mode between the vehicle-
to-vehicle distance control mode and the
conventional (fixed speed) cruise control
mode.

Once a control mode is activated, it cannot
be changed to the other cruise control
mode. To change the mode, push the ICC
switch

O

A

once to turn the system off. Then

push the ICC switch

O

A

again to turn the

system back on and select the desired
cruise control mode.

Always confirm the setting in the ICC sys-
tem display.

For the vehicle-to-vehicle distance control
mode, see “Vehicle-to-vehicle distance
control mode” (P. 5-73).

For the conventional (fixed speed) cruise
control mode, see “Conventional (fixed
speed) cruise control mode” (P. 5-90).

5-72

Starting and driving

-------------------------------------------------------------------------------------------------------------------------------------------------------------

HOW TO SELECT THE CRUISE
CONTROL MODE

Selecting

the

vehicle-to-vehicle

dis-

tance control mode:

To choose the

vehicle-to-vehicle distance control mode

O

1

, quickly push and release the ICC switch

O

A

.

Selecting the conventional (fixed speed)
cruise control mode:

To choose the con-

ventional (fixed speed) cruise control mode

O

2

, push and hold the ICC switch

O

A

for

longer than approximately 1.5 seconds. For
additional information, see “Conventional
(fixed speed) cruise control mode” (P. 5-90).

VEHICLE-TO-VEHICLE DISTANCE
CONTROL MODE

In the vehicle-to-vehicle distance control
mode, the ICC system automatically main-
tains a selected distance from the vehicle
traveling in front of you according to that
vehicle’s speed (up to the set speed), or at
the set speed when the road ahead is clear.

The ICC system is intended to enhance the
operation of the vehicle when following a
vehicle traveling in the same lane and
direction.

LSD3295

LSD3293

Starting and driving

5-73

-------------------------------------------------------------------------------------------------------------------------------------------------------------

If the radar sensor

O

1

detects a slower

moving vehicle ahead, the system will re-
duce the vehicle speed so that your vehicle
follows the vehicle in front at the selected
distance.

The system automatically controls the
throttle and applies the brakes (up to ap-
proximately 40% of vehicle braking power)
if necessary.

The detection range of the sensor is ap-
proximately 650 ft (200 m) ahead.

VEHICLE-TO-VEHICLE DISTANCE
CONTROL MODE OPERATION

LSD4551

5-74

Starting and driving

-------------------------------------------------------------------------------------------------------------------------------------------------------------

The vehicle-to-vehicle distance control
mode is designed to maintain a selected
distance from the vehicle in front of you
and can reduce the speed to match a
slower vehicle ahead. The system will de-
celerate the vehicle as necessary and if the
vehicle ahead comes to a stop, the vehicle
decelerates to a standstill. However, the ICC
system can only apply up to 40% of the
vehicle’s total braking power.

This system should only be used when traf-
fic conditions allow vehicle speeds to re-
main fairly constant or when vehicle
speeds change gradually. If a vehicle
moves into the traveling lane ahead or if a
vehicle traveling ahead rapidly decelerates,
the distance between vehicles may be-
come closer because the ICC system can-
not decelerate the vehicle quickly enough.
If this occurs, the ICC system will sound a
warning chime and blink the system dis-
play to notify the driver to take necessary
action.

The system will cancel and a warning
chime will sound if the speed is below ap-
proximately 15 mph (24 km/h) and a vehicle
is not detected ahead. The system will also
disengage when the vehicle goes above
the maximum set speed.

For additional information, see “Approach
warning” (P. 5-81).

The following items are controlled in the
vehicle-to-vehicle distance control mode:
• When there are no vehicles traveling ahead,

the

vehicle-to-vehicle

distance

control

mode maintains the speed set by the driver.
The set speed range is between approxi-
mately 0 to 90 mph (30 to 144 km/h).

• When there is a vehicle traveling ahead,

the vehicle-to-vehicle distance control
mode adjusts the speed to maintain the
distance, selected by the driver, from the
vehicle ahead. If the vehicle ahead comes
to a stop, the vehicle decelerates to a
standstill within the limitations of the sys-
tem. The system will cancel once it judges
a standstill with a warning chime.

• When the vehicle traveling ahead has

moved out from its lane of travel, the
vehicle-to-vehicle distance control mode
accelerates and maintains vehicle speed
up to the set speed.

The ICC system does not control vehicle
speed or warn you when you approach
stationary and slow moving vehicles. You
must pay attention to vehicle operation to
maintain proper distance from vehicles
ahead when approaching toll gates or traf-
fic congestion.

When driving on the freeway at a set speed
and approaching a slower traveling vehicle
ahead, the ICC system will adjust the speed
to maintain the distance, selected by the
driver, from the vehicle ahead. If the vehicle
ahead changes lanes or exits the freeway,
the ICC system will accelerate and main-
tain the speed up to the set speed. Pay
attention to the driving operation to main-
tain control of the vehicle as it accelerates
to the set speed.

SSD0254

Starting and driving

5-75

-------------------------------------------------------------------------------------------------------------------------------------------------------------

The vehicle may not maintain the set
speed on winding or hilly roads. If this oc-
curs, you will have to manually control the
vehicle speed.

Normally when controlling the distance to
a vehicle ahead, this system automatically
accelerates or decelerates your vehicle ac-
cording to the speed of the vehicle ahead.
Depress the accelerator to properly accel-
erate your vehicle when acceleration is re-
quired for a lane change. Depress the brake
pedal when deceleration is required to
maintain a safe distance to the vehicle
ahead due to its sudden braking or if a
vehicle cuts in. Always stay alert when us-
ing the ICC system.

VEHICLE-TO-VEHICLE DISTANCE
CONTROL MODE SWITCHES

The system is operated by the ICC switch
and four control switches, all mounted on
the steering wheel.

1.

CANCEL switch:

Deactivates the system without erasing
the set speed.

2.

RES+ switch:

Resumes set speed or increases speed
incrementally.

3.

DISTANCE

switch:

Changes

the

vehicle’s

following

distance:

• Long
• Middle
• Short

4.

ICC switch:

Master switch to activate the system.

5.

SET- switch:

Sets desired cruise speed or reduces
speed incrementally.

LSD3265

5-76

Starting and driving

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Vehicle-to-vehicle distance
control mode display and
indicators

The display is located between the speed-
ometer and tachometer.

1. This indicator indicates the ICC system

status depending on a color:

ICC system ON indicator (gray):

Indi-

cates that the ICC switch is on.

ICC system SET indicator (green):

In-

dicates that the cruising speed is set.

ICC system warning (yellow):

Indi-

cates that there is a malfunction in the
ICC system.

2. Set vehicle speed indicator:

Indicates the set vehicle speed.

For Canadian models, the speed is dis-
played in km/h.

3. Vehicle ahead detection indicator:

Indicates whether it detects a vehicle in
front of you.

4. Set distance indicator:

Displays the selected distance between
vehicles set with the distance switch.

Operating vehicle-to-vehicle
distance control mode

To turn on the cruise control,

quickly push

and release the ICC switch

O

A

. The ICC sys-

tem ON indicator (gray), set distance indi-
cator and set vehicle speed indicator

O

B

come on in a standby state for setting.

LSD3493

LSD3865

Starting and driving

5-77

-------------------------------------------------------------------------------------------------------------------------------------------------------------

To set cruising speed,

accelerate your ve-

hicle to the desired speed, push the SET–
switch

O

C

and release it. The ICC system

set indicator (green), vehicle ahead detec-
tion indicator, set distance indicator and
set vehicle speed indicator

O

B

will come on.

Take your foot off the accelerator pedal.
Your vehicle will maintain the set speed.

When the SET– switch is pushed under the
following conditions, the system cannot be
set and the ICC indicators will blink for ap-
proximately 2 seconds:
• When traveling below 20 mph (30 km/h)

and a vehicle ahead is not detected

• When the shift lever is not in the D (Drive)

or Manual mode

• When the parking brake is applied
• When the brakes are operated by the

driver

When the SET– switch is pushed under the
following conditions, the system cannot be
set.

A warning chime will sound and a message
will pop up:
• When the VDC system is off (To use the

ICC system, turn on the VDC system. Push
the ICC switch to turn off the ICC system
and reset the ICC switch by pushing the
ICC switch again.)

For additional information about the
VDC system, see “Vehicle Dynamic Con-
trol (VDC)” (P. 5-175).

• When VDC is operating
• When a wheel is slipping (To use the ICC

system, make sure the wheels are no lon-
ger slipping.)

LSD3866

LSD3102

5-78

Starting and driving

-------------------------------------------------------------------------------------------------------------------------------------------------------------

1

System set display with vehicle ahead

2

System set display without vehicle
ahead

The driver sets the desired vehicle speed
based on the road conditions. The ICC sys-
tem maintains the set vehicle speed, simi-
lar to standard cruise control, as long as no
vehicle is detected in the lane ahead. The
ICC system displays the set speed.

Vehicle detected ahead

When a vehicle is detected in the lane
ahead, the ICC system decelerates the ve-
hicle by controlling the throttle and apply-
ing the brakes to match the speed of a
slower vehicle ahead. The system then
controls the vehicle speed based on the
speed of the vehicle ahead to maintain the
driver selected distance.

NOTE:
• The stop lights of the vehicle come on

when braking is performed by the ICC
system.

• When the brake operates, a noise may

be heard. This is not a malfunction.

When a vehicle ahead is detected, the ve-
hicle ahead detection indicator comes on.
The ICC system will also display the set
speed and selected distance.

Vehicle ahead not detected

When a vehicle is no longer detected
ahead, the ICC system gradually acceler-
ates your vehicle to resume the previously
set vehicle speed. The ICC system then
maintains the set speed.

When a vehicle is no longer detected, the
vehicle ahead detection indicator turns off.

If a vehicle ahead appears during accelera-
tion to the set vehicle speed or any time the
ICC system is in operation, the system con-
trols the distance to that vehicle.

When a vehicle is no longer detected under
approximately 15 mph (25 km/h), the sys-
tem will be canceled.

LSD3496

Starting and driving

5-79

-------------------------------------------------------------------------------------------------------------------------------------------------------------

When passing another vehicle,

the set

speed indicator

O

A

will flash when the ve-

hicle speed exceeds the set speed. The ve-
hicle detect indicator will turn off when the
area ahead of the vehicle is open. When the
pedal is released, the vehicle will return to
the previously set speed.

Even though your vehicle speed is set in the
ICC system, you can depress the accelera-
tor pedal when it is necessary to accelerate
your vehicle rapidly.

How to change the set vehicle
speed

To cancel the preset speed,

use one of the

following methods:
• Push the CANCEL switch. The set vehicle

speed indicator will go out.

• Tap the brake pedal. The set vehicle

speed indicator will go out.

• Turn the ICC switch off. The ICC indicators

will go out.

To reset at a faster cruising speed,

use

one of the following methods:
• Depress the accelerator pedal. When the

vehicle attains the desired speed, push
and release the SET– switch.

• Push and hold the RES+ switch. The set

vehicle speed will increase by approxi-
mately 5 mph (5 km/h).

• Push, then quickly release the RES+

switch. Each time you do this, the set
speed will increase by approximately 1
mph (1 km/h).

To reset at a slower cruising speed,

use

one of the following methods:
• Lightly tap the brake pedal. When the ve-

hicle attains the desired speed, push the
SET– switch and release it.

• Push and hold the SET– switch. The set

vehicle speed will decrease by approxi-
mately 5 mph (5 km/h).

• Push, then quickly release the SET–

switch. Each time you do this, the set
speed will decrease by approximately 1
mph (1 km/h).

To resume the preset speed,

push and

release the RES+ switch. The vehicle will
resume the last set cruising speed when
the vehicle speed is over 20 mph (30 km/h).

LSD3267

5-80

Starting and driving

-------------------------------------------------------------------------------------------------------------------------------------------------------------

How to change the set distance
to the vehicle ahead

The distance to the vehicle ahead can be
selected at any time depending on the traf-
fic conditions.

Each time the distance switch

O

A

is

pushed, the set distance will change to
long, middle, short and back to long again,
in that sequence.

Distance Approximate distance at

60 mph (100 km/h)
[ft (m)]

1.

Long

200 (60)

2.

Middle

150 (45)

3.

Short

90 (30)

• The distance to the vehicle ahead will

change according to the vehicle speed.
The higher the vehicle speed, the longer
the distance.

• The distance setting will remain the cur-

rent

setting

even

if

the

engine

is

restarted.

Approach warning

If your vehicle comes closer to the vehicle
ahead due to rapid deceleration of that ve-
hicle or if another vehicle cuts in, the sys-
tem warns the driver with the chime and
ICC system display. Decelerate by depress-
ing the brake pedal to maintain a safe ve-
hicle distance if:
• The chime sounds.
• The vehicle ahead detection indicator

blinks.

The warning chime may not sound in
some cases when there is a short distance
between vehicles. Some examples are:
• When the vehicles are traveling at the

same speed and the distance between
vehicles is not changing.

• When the vehicle ahead is traveling faster

and the distance between vehicles is
increasing.

• When a vehicle cuts in near your vehicle.

The warning chime will not sound when:
• The vehicle approaches other vehicles

that are parked or moving slowly.

• The accelerator pedal is depressed, over-

riding the system.

LSD3222

LSD2778

Starting and driving

5-81

-------------------------------------------------------------------------------------------------------------------------------------------------------------

NOTE:

The approach warning chime may sound
and the system display may blink when
the ICC sensor detects objects on the
side of the vehicle or on the side of the
road. This may cause the ICC system to
decelerate or accelerate the vehicle. The
ICC sensor may detect these objects
when the vehicle is driven on winding
roads, narrow roads, hilly roads, or when
entering or exiting a curve. In these
cases you will have to manually control
the proper distance ahead of your
vehicle.

Also, the sensor sensitivity can be affected
by vehicle operation (steering maneuver or
driving position in the lane) or traffic or ve-
hicle condition (for example, if a vehicle is
being driven with some damage).

Automatic cancellation

A chime sounds under the following condi-
tions and the control is automatically can-
celed:
• When the vehicle ahead is not detected

and your vehicle is traveling below the
speed of 15 mph (25 km/h)

• When the system judges the vehicle is at

a standstill

• When the shift lever is not in the D (Drive)

position, Manual mode or L (Low) range.

• When the parking brake system is applied
• When the VDC system is turned off
• When VDC operates
• When distance measurement becomes

impaired due to adhesion of dirt or ob-
struction to the sensor

• When a wheel slips
• When the radar signal is temporarily

interrupted

VEHICLE-TO-VEHICLE DISTANCE
CONTROL MODE LIMITATIONS

WARNING

Listed below are the system limitations
for the ICC system. Failure to operate
the vehicle in accordance with these
system limitations could result in seri-
ous injury or death.

The ICC system is primarily intended
for use on straight, dry, open roads
with light traffic. It is not advisable to
use the ICC system in city traffic or
congested areas.

The ICC system will not adapt auto-
matically to road conditions. This
system should be used in evenly
flowing traffic. Do not use the system
on roads with sharp curves, or on icy
roads, in heavy rain or in fog.

As there is a performance limit to the
distance control function, never rely
solely on the ICC system. This system
does not correct careless, inattentive
or absentminded driving, or over-
come poor visibility in rain, fog, or
other bad weather. Decelerate the
vehicle speed by depressing the
brake pedal, depending on the dis-
tance to the vehicle ahead and the
surrounding circumstances in order
to maintain a safe distance between
vehicles.

If the vehicle ahead comes to a stop,
the vehicle decelerates to a standstill
within the limitations of the system.
The system will cancel once it judges
that the vehicle has come to a stand-
still and sound a warning chime. To
prevent the vehicle from moving, the
driver must depress the brake pedal.

5-82

Starting and driving

-------------------------------------------------------------------------------------------------------------------------------------------------------------

 

 

 

 

 

 

 

Content      ..     21      22      23      24     ..