Nissan Kicks (2022 year). Manual in english - page 8

 

  Index      Manuals     Nissan Kicks (2022 year). Manual in english

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

 

 

 

Content      ..     6      7      8      9     ..

 

 

 

Nissan Kicks (2022 year). Manual in english - page 8

 

 

This indicator means that the engine will
start by pushing the ignition switch with
the brake pedal depressed. You can start
the engine from any position of the ignition
switch.

Rear seat belt reminder

This warning appears for 65 seconds after
the ignition is placed in the ON position and
the engine is started.

This warning message shows the status of
the three rear seat belts. When one of the
rear seat belts are buckled, the corre-
sponding rear seat belt indicator will ap-
pear white. When one of the rear seat belts
are unbuckled, the corresponding rear seat
belt indicator will appear red.

After a change in buckle status, a chime will
sound and the warning will appear for an-
other 65 seconds.

Release Parking Brake

This warning appears in the message area
of the vehicle information display when the
parking brake is set and the vehicle is
driven.

Reminder: Turn OFF
Headlights

This warning appears when the headlights
are left in the ON position when exiting the
vehicle. Place the headlight switch in the
OFF (if so equipped) or AUTO position. For
additional information, see “Headlight and
turn signal switch” (P. 2-43).

Shift to Park

This warning appears when the ignition
switch is in the OFF position and the shift
lever is not in the P (Park) position. Also, a
chime sounds when the ignition switch is
in the OFF position.

If this warning appears, move the shift lever
to the P (Park) position and start the engine.

Shipping Mode On Push Storage Fuse

This warning may appear if the extended
storage switch is not pushed in. When this
warning appears, push in the extended
storage switch to turn off the warning. For
additional information, see “Extended stor-
age switch” (P. 2-59).

Steep slope Apply foot
brake

This warning appears if the “Caution Steep
slope” warning has appeared over about 3
minutes. Then the parking brake will auto-
matically be applied and the brake force of
the automatic brake hold will be released,
and the vehicle may move or roll away un-
expectedly. Apply the foot brake to stop the
vehicle from moving.

For additional information, see “Automatic
brake hold” (P. 5-25).

Steering lock release
malfunction indicator

This indicator appears when the steering
lock cannot be released.

If this indicator appears, push the ignition
switch while lightly turning the steering
wheel right and left.

Tire

This indicator appears when the customer
set distance is reached for replacing tires.
You can set or reset the distance for replac-
ing tires.

2-34

Instruments and controls

-------------------------------------------------------------------------------------------------------------------------------------------------------------

WARNING

The tire replacement indicator is not a
substitute for regular tire checks, in-
cluding tire pressure checks. For addi-
tional

information,

see

“Changing

wheels and tires” (P. 8-36). Many factors
including tire inflation, alignment, driv-
ing habits and road conditions affect
tire wear and when tires should be re-
placed. Setting the tire replacement in-
dicator for a certain driving distance
does not mean your tires will last that
long. Use the tire replacement indicator
as a guide only and always perform
regular tire checks. Failure to perform
regular tire checks, including tire pres-
sure checks could result in tire failure.
Serious vehicle damage could occur
and may lead to a collision, which could
result in serious personal injury or
death.

Tire Pressure Low - Add Air

This warning appears when the low tire
pressure warning light in the meter illumi-
nates and low tire pressure is detected. The
warning appears each time the ignition
switch is placed in the ON position as long
as the low tire pressure warning light re-
mains illuminated. If this warning appears,

stop the vehicle and adjust the tire pres-
sures of all four tires to the recommended
COLD tire pressure shown on the Tire and
Loading Information label. For additional
information, see “Low tire pressure warning
light” (P. 2-17) and “Tire Pressure Monitoring
System (TPMS)” (P. 5-5).

TPMS Error: See Owner’s Manual

This warning appears when there is an er-
ror with your TPMS. If this warning comes
on, have the system checked. It is recom-
mended that you visit a NISSAN dealer for
this service.

Transmission Shift Position
indicator

This indicator shows the transmission shift
position.

CVT Error: See Owner's
Manual

This warning appears when there is a
problem with the CVT system. If this
warning

appears,

have

the

system

checked. It is recommended that you visit a
NISSAN dealer for this service.

Automatic Emergency
Braking (AEB) emergency
warning indicator

This indicator appears along, with an au-
dible warning, when the system detects
the possibility of a forward collision.

For additional information, see “Automatic
Emergency Braking (AEB)” (P. 5-88), “Auto-
matic Emergency Braking (AEB) with Pe-
destrian Detection” (P. 5-98) and “Intelligent
Forward Collision Warning (I-FCW)” (P. 5-111).

Blind Spot Warning (BSW)
indicator

This indicator appears when the BSW sys-
tem is engaged.

For additional information, see “Blind Spot
Warning (BSW)” (P. 5-35).

Cruise control indicator

This indicator shows the cruise control sys-
tem status.

For additional information, see “Cruise con-
trol” (P. 5-56).

Instruments and controls

2-35

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Drive Sport mode indicator

A small “S” appears to the right of the Trans-
mission Shift Position indicator in the ve-
hicle information display when the Drive
Sport mode is engaged.

Activate the Drive Sport mode by pressing
the switch on the shift lever while the shift
lever is in the D (Drive) position.

For additional information, see “Drive sport
mode switch” (P. 5-21).

Driver Attention Alert —
System Fault

This warning appears when the Intelligent
Driver Alertness (I-DA) system is not func-
tioning properly. For additional information,
see

Intelligent

Driver

Alertness

(I-DA)

(P. 5-126).

Driver Attention Alert -
Take a Break?

This alert appears when the system has
detected that the driver may be displaying
fatigue or a lack of attention.

Forward Driving Aids Temporarily
Disabled Front Sensor Blocked See
Owner’s Manual

This message appears when the front ra-
dar sensor may be obstructed due to:
• mud, dirt, snow, ice, etc.
• inclement weather (rain, fog, snow, etc.)

All forward driving aids are temporarily dis-
abled until the system detects that the
front radar sensor is no longer obstructed.

For additional information, see the follow-
ing (if so equipped):
• Automatic

Emergency

Braking

(AEB)

(P. 5-88)

• Automatic Emergency Braking (AEB) with

Pedestrian Detection (P. 5-98)

• Intelligent Cruise Control (ICC) (P. 5-58)
• Intelligent Forward Collision Warning (I-

FCW) (P. 5-111)

Intelligent Cruise Control
(ICC) indicators

These

indicators

show

the

Intelligent

Cruise Control (ICC) system status. The sta-
tus is shown by color. For additional infor-
mation, see “Intelligent Cruise Control (ICC)”
(P. 5-58).

Lane Departure Warning
(LDW) indicator

This indicator appears when the LDW sys-
tem is engaged.

For additional information, see “Lane De-
parture Warning (LDW)” (P. 5-28).

Malfunction

This warning appears when one or more of
the following systems (if so equipped) is
not functioning properly:
• Automatic Emergency Braking (AEB)
• Blind Spot Warning (BSW)
• Rear Cross Traffic Alert (RCTA)

If one or more of these warning appears,
have the system checked. It is recom-
mended that you visit a NISSAN dealer for
this service.

Rear Automatic Braking
(RAB) indicator

This indicator appears to indicate the sta-
tus of the Rear Automatic Braking (RAB)
system. For additional information, see
“Rear Automatic Braking (RAB)” (P. 5-81).

2-36

Instruments and controls

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Side Radar Obstruction

This message appears when the Blind
Spot Warning (BSW) or Rear Cross Traffic
Alert (RCTA) systems become unavailable
because a radar blockage is detected. For
additional information, see “Blind Spot
Warning (BSW)” (P. 5-35) or “Rear Cross Traf-
fic Alert (RCTA)” (P. 5-46).

System Fault

This warning appears if there is a malfunc-
tion in the Rear Automatic Braking (RAB)
system. For additional information, see
“Rear Automatic Braking (RAB)” (P. 5-81).

Vehicle ahead detection
indicator

This indicator appears when the Auto-
matic Emergency Braking (AEB) system is
engaged and has detected a vehicle.

For additional information, see “Automatic
Emergency Braking (AEB)” (P. 5-88) or “Auto-
matic Emergency Braking (AEB) with Pe-
destrian Detection” (P. 5-98).

Unavailable: High Cabin Temperature

This message appears when the camera
detects an interior temperature of more
than approximately 104°F (40°C). For addi-
tional information, see “Lane Departure
Warning (LDW)” (P. 5-28).

Your vehicle may have three types of secu-
rity systems:
• Vehicle security system
• NISSAN Anti-Theft System
• NISSAN Vehicle Immobilizer System

VEHICLE SECURITY SYSTEM (if so
equipped)

The vehicle security system provides visual
and audible alarm signals if someone
opens the doors, hood or liftgate when the
system is armed. It is not, however, a mo-

tion detection type system that activates
when a vehicle is moved or when a vibra-
tion occurs.

The system helps deter vehicle theft but
cannot prevent it, nor can it prevent the
theft of interior or exterior vehicle compo-
nents in all situations. Always secure your
vehicle even if parking for a brief period.
Never leave your keys in the vehicle, and
always lock the vehicle when unattended.
Be aware of your surroundings, and park in
secure, well-lit areas whenever possible.

Many devices offering additional protec-
tion, such as component locks, identifica-
tion markers, and tracking systems, are
available at auto supply stores and spe-
cialty shops. A NISSAN dealer may also offer
such equipment. Check with your insur-
ance company to see if you may be eligible
for discounts for various theft protection
features.

How to arm the vehicle security
system

1. Close all windows.

(The system can be

armed even if the windows are open.)

2. Remove the keys from the vehicle.

LIC3633

SECURITY SYSTEMS (if so equipped)

Instruments and controls

2-37

-------------------------------------------------------------------------------------------------------------------------------------------------------------

3. Close all doors, hood and liftgate. Lock

all doors. The doors can be locked with
the Intelligent Key, mechanical key, or
door

handle

request

switch

(if

so

equipped).

4. Confirm that the

security indicator

light stays on for about 30 seconds. The
vehicle security system is now pre-
armed. The vehicle security system will
automatically

shift

into

the

armed

phase. The

security light begins to

flash once every three seconds. If during
the pre-armed phase one of the follow-
ing occurs, the system will not arm:

• Any door is unlocked with the Intelligent

Key, mechanical key, or door request
switch (if so equipped).

• Ignition switch is placed in the ON

position.

Even when the driver and/or passen-
gers are in the vehicle, the system will
activate with all the doors, hood and
liftgate locked with the ignition switch
placed in the LOCK position. When plac-
ing the ignition switch in the ON posi-
tion, the system will be released.

Vehicle security system activation

The vehicle security system will give the
following alarm:
• The headlights or turn lamps blink and

the

horn

sounds

intermittently

but

synchronously.

• The alarm automatically turns off after a

period of time. However, the alarm reacti-
vates if the vehicle is tampered with
again.

The alarm is activated by:
• opening any door, hood or the liftgate

without using the key or Intelligent Key
(even if the door is unlocked by releasing
the door inside lock knob).

How to stop an activated alarm

The alarm stops only by unlocking a door
or the liftgate with the key fob, pressing the

button on the Intelligent Key, or push-

ing the request switch (if so equipped) on
the driver's or passenger's door with the
Intelligent Key in range of the door handle.

NISSAN ANTI-THEFT SYSTEM
(NATS) (if so equipped)

The NISSAN Anti-Theft System will not al-
low the engine to start without the use of a
registered NATS key.

If the engine does not start using the reg-
istered NATS key, it may be due to interfer-
ence caused by:
• Another NATS key
• Automated toll road device
• Automated payment device
• Other

devices

that

transmit

similar

signals

Start

the

engine

using

the

following

procedure:

1. Remove any items that may be causing

the interference away from the NATS key.

2. Leave the ignition switch in the ON posi-

tion for approximately 5 seconds.

3. Place the ignition switch in the OFF or

LOCK position and wait approximately
10 seconds.

4. Repeat steps 2 and 3 again.

5. Start the engine.

6. Repeat the steps above until all possible

interferences are eliminated.

If this procedure allows the engine to start,
NISSAN recommends placing the regis-
tered NATS key separate from other de-
vices to avoid interference.

2-38

Instruments and controls

-------------------------------------------------------------------------------------------------------------------------------------------------------------

NISSAN VEHICLE IMMOBILIZER
SYSTEM (if so equipped)

The NISSAN Vehicle Immobilizer System
will not allow the engine to start without
the use of a registered key.

If the engine fails to start using a registered
key (for example, when interference is
caused by another registered key, an auto-
mated toll road device or automatic pay-
ment device on the key ring), restart the
engine using the following procedures:

1. Leave the ignition switch in the ON posi-

tion for approximately 5 seconds.

2. Place the ignition switch in the OFF or

LOCK position, and wait approximately
10 seconds.

3. Repeat steps 1 and 2.

4. Restart the engine while holding the de-

vice (which may have caused the inter-
ference) separate from the registered
key.

If the no start condition re-occurs, NISSAN
recommends placing the registered key on
a separate key ring to avoid interference
from other devices.

FCC Notice:

For USA:

This device complies with Part 15 of the
FCC Rules. Operation is subject to the fol-
lowing two conditions; (1) This device
may not cause harmful interference, and
(2) this device must accept any interfer-
ence received, including interference
that may cause undesired operation of
the device.

NOTE:

Changes or modifications not expressly
approved by the party responsible for
compliance could void the user's author-
ity to operate the equipment.

For Canada:

This

device

contains

licence-exempt

transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence-exempt
RSS(s). Operation is subject to the fol-
lowing two conditions: (1) This device
may not cause interference. (2) This de-
vice must accept any interference, in-
cluding interference that may cause un-
desired operation of the device.

Security indicator light (if so
equipped)

The security indicator light blinks whenever
the ignition switch is placed in the OFF or
LOCK position.

This function indicates the NISSAN Anti-
Theft System (NATS) is operational.

If the NATS is malfunctioning, the light will
remain on while the ignition switch is
placed in the ON position.

LIC0474

Instruments and controls

2-39

-------------------------------------------------------------------------------------------------------------------------------------------------------------

If the light still remains on and/or the
engine will not start, seek service for the
NATS as soon as possible. Please bring all
registered keys that you have. It is rec-
ommended that you visit a NISSAN
dealer for this service.

SWITCH OPERATION

WARNING

In freezing temperatures the washer
solution may freeze on the windshield
and obscure your vision which may
lead to an accident. Warm the wind-
shield with the defroster before you
wash the windshield.

CAUTION

Do not operate the washer continu-
ously for more than 30 seconds.

Do not operate the washer if the
windshield-washer fluid reservoir is
empty.

Do not fill the windshield-washer
fluid

reservoir

with

windshield-

washer fluid concentrates at full
strength.

Some

methyl

alcohol

based windshield-washer fluid con-
centrates may permanently stain the
grille

if

spilled

while

filling

the

windshield-washer fluid reservoir.

Pre-mix

windshield-washer

fluid

concentrates

with

water

to

the

manufacturer’s recommended levels
before pouring the fluid into the
windshield-washer fluid reservoir.
Do not use the windshield-washer
fluid reservoir to mix the windshield-
washer fluid concentrate and water.

NOTE:

If the windshield wiper operation is in-
terrupted by snow or ice, the wiper may
stop moving to protect its motor. If this
occurs, turn the wiper switch to the OFF
position and remove the snow or ice that
is on and around the wiper arms. In ap-
proximately 1 minute, turn the switch on
again to operate the wiper.

LIC2661

WIPER AND WASHER SWITCH

2-40

Instruments and controls

-------------------------------------------------------------------------------------------------------------------------------------------------------------

The windshield wiper and washer operates
when the ignition switch is in the ON
position.

Push the lever down to operate the wiper
at the following speed:

1

Intermittent — intermittent operation
can be adjusted by turning the knob
toward

O

A

(faster) or

O

B

(slower). Also,

the intermittent operation speed varies
in accordance with the vehicle speed (if
so equipped). (For example, when the
vehicle speed is high, the intermittent
operation speed will be faster.)

2

Low — continuous low speed operation

3

High

continuous

high

speed

operation

Push the lever up

O

4

to have one sweep

operation (MIST) of the wiper.

Pull the lever toward you

O

5

to operate the

washer. The wiper will also operate several
times.

NOTE:

The Wiper with Speed feature may be
disabled. For additional information, see
“Vehicle information display” (P. 2-23).

REAR SWITCH OPERATION

WARNING

In freezing temperatures the washer
solution may freeze on the rear window
and obscure your vision which may
lead to an accident. Warm the rear win-
dow with the defroster before you
wash the rear window.

CAUTION

Do not operate the washer continu-
ously for more than 30 seconds.

Do not operate the washer if the
windshield-washer fluid reservoir is
empty.

Do not fill the windshield-washer
fluid

reservoir

with

windshield-

washer fluid concentrates at full
strength.

Some

methyl

alcohol

based windshield-washer fluid con-
centrates may permanently stain the
grille

if

spilled

while

filling

the

windshield-washer fluid reservoir.

Pre-mix

windshield-washer

fluid

concentrates

with

water

to

the

manufacturer’s recommended levels
before pouring the fluid into the
windshield-washer fluid reservoir.
Do not use the windshield-washer
fluid reservoir to mix the windshield-
washer fluid concentrate and water.

NOTE:

If the rear window wiper operation is in-
terrupted by snow, etc., the wiper may
stop moving to protect its motor. If this
occurs, turn the wiper switch to OFF and
remove the snow, etc. on and around the
wiper arms. After about 1 minute, turn
the switch on again to operate the wiper.

LIC2662

Instruments and controls

2-41

-------------------------------------------------------------------------------------------------------------------------------------------------------------

The rear window wiper and washer oper-
ate when the ignition switch is in the ON
position. Turn the switch clockwise from
the OFF position to operate the wiper.

1

Intermittent — intermittent operation
(not adjustable)

2

Low — continuous low speed operation

Push the switch forward

O

3

to operate the

washer. The wiper will also operate several
times.

If the windshield wipers are on and the ve-
hicle is placed in R (Reverse) the rear wiper
will automatically turn on while the vehicle
remains in R (Reverse).

NOTE:

The Reverse Link feature may be dis-
abled. For additional information, see
“Vehicle information display” (P. 2-23).

To defrost the rear window glass, start the
engine and push the rear window defroster
switch on. The rear window defroster indi-
cator light on the switch comes on. Push
the switch again to turn the defroster off.

To defrost the outside mirrors (if so
equipped), start the engine and push the
outside mirror defroster switch on. The
outside mirror defroster indicator light on
the switch comes on. Push the switch
again to turn the defroster off.

The rear window/outside mirror defroster
(if so equipped) automatically turns off af-
ter approximately 15 minutes.

NOTE:

Use defroster and/or outside mirror de-
froster when engine is running to avoid
discharging the battery.

CAUTION

When cleaning the inner side of the rear
window, be careful not to scratch or
damage the rear window defroster.

LIC3600

Type A (if so equipped)

LIC3570

Type B (if so equipped)

REAR WINDOW AND OUTSIDE
MIRROR (if so equipped)
DEFROSTER SWITCH

2-42

Instruments and controls

-------------------------------------------------------------------------------------------------------------------------------------------------------------

HEADLIGHT CONTROL SWITCH

Lighting

1

Rotate the switch to the

position,

and the side, tail, license plate, and in-
strument panel lights will come on.

2

Rotate the switch to the

position,

and the headlights will come on and all
the other lights remain on.

CAUTION

Use the headlights with the engine run-
ning to avoid discharging the vehicle
battery.

LIC2634

Type A (if so equipped)

LIC4008

Type B (if so equipped)

LIC4237

Type C (if so equipped)

HEADLIGHT AND TURN SIGNAL
SWITCH

Instruments and controls

2-43

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Autolight system

The autolight system allows the headlights
to turn on and off automatically. The auto-
light system can:
• Turn on the headlights, front parking, tail,

license plate and instrument panel lights
automatically when it is dark.

• Turn off all the lights when it is light.
• Keep all the lights on for a period of time

after you place the ignition switch in the
OFF position and all doors are closed.

NOTE:
Autolight activation sensitivity and
the time delay for autolight shutoff
can be adjusted. For additional infor-
mation, see “Vehicle information dis-
play” (P. 2-23).

To turn on the autolight system:

1. Turn the headlight switch to the AUTO

position

O

1

.

2. Place the ignition switch in the ON

position.

LIC4498

Type D (if so equipped)

LIC2636

Type A (if so equipped)

LIC4950

Type B (if so equipped)

2-44

Instruments and controls

-------------------------------------------------------------------------------------------------------------------------------------------------------------

3. The

autolight

system

automatically

turns the headlights on and off.

Initially, if the ignition switch is placed in the
OFF position and a door is opened and left
open, the headlights remain on for a period
of time. If another door is opened while the
headlights are on, then the timer is reset.

To turn the autolight system off, turn the
switch to the OFF (if so equipped),

, or

position.

The headlights will turn on automatically at
twilight or in rainy weather (when the wind-
shield wiper is operated continuously).

If the ignition switch is placed in the OFF
position and one of the doors is opened
and this condition is continued, the head-
lights remain on for 5 minutes.

Be sure you do not put anything on top
of the autolight sensor located in the top
side

O

1

of the instrument panel. The au-

tolight sensor controls the autolight; if it
is covered, the autolight sensor reacts as
if it is dark out and the headlights will
illuminate. If this occurs while parked
with the engine off and the ignition
switch placed in the ON position, your
vehicle's

battery

could

become

discharged.

Headlight beam select

1

To select the high beam function, push
the lever forward while the low beams
are on. The high beam lights come on
and the

indicator light illuminates.

2

Pull the lever back to return to the low
beam.

3

Pulling and releasing the lever flashes
the headlight high beams on and off.
The low beams do not need to be on
for this to function.

LIC4006

LIC2637

Instruments and controls

2-45

-------------------------------------------------------------------------------------------------------------------------------------------------------------

High Beam Assist (if so equipped)

The High Beam Assist system will operate
when the vehicle is driven at speeds of ap-
proximately 25 mph (40 km/h) and above. If
an oncoming vehicle or leading vehicle ap-
pears in front of your vehicle when the
headlight high beam is on, the headlight
will

be

switched

to

the

low

beam

automatically.

WARNING

The High Beam Assist system is a
convenience but it is not a substitute
for safe driving operation. The driver
should remain alert at all times, en-
sure

safe

driving

practices

and

switch the high beams and low beam
manually when necessary.

The high beam or low beam may not
switch automatically under the fol-
lowing conditions. Switch the high
beam and low beam manually.

During bad weather (rain, fog,
snow, wind, etc.).

When a light source similar to a
headlight or tail light is in the vi-
cinity of the vehicle.

When the headlights of the on-
coming vehicle or the leading ve-
hicle are turned off, when the color
of the light is affected due to for-
eign materials on the lights, or
when the light beam is out of
position.

When there is a sudden, continu-
ous change in brightness.

When driving on a road that
passes over rolling hills, or a road
that has level differences.

When driving on a road with many
curves.

When a sign or mirror-like surface
is reflecting intense light towards
the front of the vehicle.

When the container, etc. being
towed by a leading vehicle is re-
flecting intense light.

When a headlight on your vehicle
is damaged or dirty.

When the vehicle is leaning at an
angle due to a punctured tire, be-
ing towed, etc.

The timing of switching the low
beam and high beam may change
under the following situations.

The brightness of the headlights
of the oncoming vehicle or leading
vehicle.

The movement and direction of
the oncoming vehicle and the
leading vehicle.

When only one light on the on-
coming vehicle or the leading ve-
hicle is illuminated.

When the oncoming vehicle or the
leading vehicle is a two-wheeled
vehicle.

Road conditions (incline, curve,
the road surface, etc.).

The number of passengers and
the amount of luggage.

2-46

Instruments and controls

-------------------------------------------------------------------------------------------------------------------------------------------------------------

High Beam Assist operation

To activate the High Beam Assist system,
turn the headlight switch to the AUTO po-
sition

O

1

and push the lever forward

O

2

(high beam position). The

High Beam

Assist indicator light in the meter will illumi-
nate while the headlights are turned on.

If the High Beam Assist indicator light does
not illuminate in the above condition, it may
indicate that the system is not functioning
properly. Have the system checked, it is
recommended that you visit a NISSAN
dealer for this service.

When the vehicle speed lowers to less than
approximately 16 mph (25 km/h), the head-
light uses the low beam.

To turn off the High Beam Assist system,
turn the headlight switch to the

posi-

tion or select the low beam position by
placing the lever in the neutral position.

Ambient image sensor maintenance

The ambient image sensor

O

A

for the High

Beam Assist system is located in front of
the inside mirror. To maintain the proper
operation of the high beam assist system
and prevent a system malfunction, be sure
to observe the following:
• Always keep the windshield clean.
• Do not attach a sticker (including trans-

parent material) or install an accessory
near the ambient image sensor.

• Do not strike or damage the areas

around the ambient image sensor. Do
not touch the sensor lens that is located
on the ambient image sensor.

LIC3696

LIC4969

Instruments and controls

2-47

-------------------------------------------------------------------------------------------------------------------------------------------------------------

If the ambient image sensor is damaged
due to an accident, it is recommended that
you visit a NISSAN dealer.

Battery saver system

The battery saver system automatically
turns off the ignition after a period of time
when the ignition switch is left in the ON
position.

The battery saver system automatically
turns off the following lights after a period
of time when the ignition switch is placed in
the OFF position:
• Headlights, when the headlight switch is

in the

or

position

• Interior lights, when left in the ON position

CAUTION

Even though the battery saver feature
automatically turns off the headlights
after a period of time, you should turn
the headlight switch to the OFF posi-
tion (if so equipped) when the engine is
not running to avoid discharging the
vehicle battery.

DAYTIME RUNNING LIGHTS (DRL)
SYSTEM (Type A) (if so equipped)

The DRL portion of the fog light assembly
automatically illuminates when the engine
is started with the parking brake released.
The DRL operate with the headlight switch
in the OFF or AUTO position. Turn the head-
light switch to the

position for full

illumination when driving at night. (The DRL
will turn off.)

If the parking brake is applied before the
engine is started, the DRL do not illuminate.
The DRL illuminate once the parking brake
is released. The DRL will remain on until the
ignition switch is placed in the OFF position.

It is necessary at dusk to turn the headlight
switch on for interior controls and switches
to illuminate, as those remain off while the
switch is in the OFF or AUTO position.

WARNING

When the DRL system is active, tail
lights on your vehicle are not on. It is
necessary at dusk to turn on your
headlights. Failure to do so could cause
an

accident

injuring

yourself

and

others.

LED DAYTIME RUNNING LIGHTS
(DRL) SYSTEM (Type B) (if so
equipped)

The LED DRL portion of the fog light assem-
bly automatically illuminates when the en-
gine is started with the parking brake re-
leased. The LED DRL operate with the
headlight switch in the OFF or AUTO posi-
tion. Turn the headlight switch to the
position for full illumination when driving at
night. (The LED DRL will turn off.)

If the parking brake is applied before the
engine is started, the LED DRL do not illumi-
nate. The LED DRL illuminate once the
parking brake is released. The LED DRL will
remain on until the ignition switch is placed
in the OFF position.

It is necessary at dusk to turn the headlight
switch on for interior controls and switches
to illuminate, as those remain off while the
switch is in the OFF or AUTO position.

WARNING

When the LED DRL system is active, tail
lights on your vehicle are not on. It is
necessary at dusk to turn on your head-
lights. Failure to do so could cause an
accident injuring yourself and others.

2-48

Instruments and controls

-------------------------------------------------------------------------------------------------------------------------------------------------------------

INSTRUMENT BRIGHTNESS
CONTROL

Turn the control knob

O

A

to adjust the

brightness of instrument panel lights.

TURN SIGNAL SWITCH

Turn signal

1

Move the lever up or down to signal the
turning direction. When the turn is com-
pleted,

the

turn

signal

cancels

automatically.

Lane change signal

2

Move the lever up or down until the turn
signal begins to flash, but the lever
does not latch, to signal a lane change.
Hold the lever until the lane change is
completed.

LIC4150

Type A (if so equipped)

LIC4151

Type B (if so equipped)

LIC2638

Instruments and controls

2-49

-------------------------------------------------------------------------------------------------------------------------------------------------------------

 

 

 

 

 

 

 

Content      ..     6      7      8      9     ..