Nissan Murano (2022 year). Manual in english - page 7

 

  Index      Manuals     Nissan Murano (2022 year). Manual in english

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

 

 

 

Content      ..     5      6      7      8     ..

 

 

 

Nissan Murano (2022 year). Manual in english - page 7

 

 

When using a wheel without the
TPMS such as the spare tire, the TPMS
will not function and the low tire
pressure warning light will flash for
approximately 1 minute. The light will
remain on after 1 minute. Have your
tires replaced and/or TPMS system
reset as soon as possible. It is recom-
mended that you visit a NISSAN
dealer for these services.

Replacing tires with those not origi-
nally specified by NISSAN could af-
fect the proper operation of the
TPMS.

CAUTION

The TPMS is not a substitute for the
regular tire pressure check. Be sure
to check the tire pressure regularly.

If the vehicle is being driven at
speeds of less than 16 mph (25 km/h),
the TPMS may not operate correctly.

Be sure to install the specified size of
tires to the four wheels correctly.

Malfunction Indicator Light
(MIL)

If this indicator light comes on steady or
blinks while the engine is running, it may
indicate

a

potential

emission

control

malfunction.

The MIL may also come on steady if the
fuel-filler cap is loose or missing, or if the
vehicle runs out of fuel. Check to make sure
the fuel-filler cap is installed and closed
tightly, and that the vehicle has at least 3
gallons (11.4 liters) of fuel in the fuel tank.

After a few driving trips, the

light

should turn off if no other potential emis-
sion control system malfunction exists.

If this indicator light comes on steady for 20
seconds and then blinks for 10 seconds
when the engine is not running, it indicates
that the vehicle is not ready for an emission
control system inspection/maintenance
test. For additional information, see “Readi-
ness for Inspection/Maintenance (I/M) test”
(P. 10-32).

Operation

The MIL will come on in one of two ways:
• MIL on steady — An emission control sys-

tem malfunction has been detected.
Check the fuel-filler cap if the Loose Fuel
Cap warning appears in the vehicle infor-
mation display. If the fuel-filler cap is loose
or missing, tighten or install the cap and
continue to drive the vehicle. The
light should turn off after a few driving
trips. If the

light does not turn off

after a few driving trips, have the vehicle
inspected. It is recommended that you
visit a NISSAN dealer for this service. You
do not need to have your vehicle towed
to the dealer.

• MIL blinking — An engine misfire has been

detected which may damage the emis-
sion control system. To reduce or avoid
emission control system damage:

– do not drive at speeds above 45 mph

(72 km/h).

– avoid

hard

acceleration

or

deceleration.

– avoid steep uphill grades.
– if possible, reduce the amount of cargo

being hauled or towed.

Instruments and controls

2-13

-------------------------------------------------------------------------------------------------------------------------------------------------------------

The MIL may stop blinking and come on
steady. Have the vehicle inspected. It is rec-
ommended that you visit a NISSAN dealer
for this service. You do not need to have
your vehicle towed to the dealer.

CAUTION

Continued vehicle operation without
having the emission control system
checked and repaired as necessary
could lead to poor driveability, reduced
fuel economy, and possible damage to
the emission control system.

Master warning light

When the ignition switch is in the ON posi-
tion, the master warning light illuminates if
any of the following are displayed on the
vehicle information display:
• No Key Detected warning
• Low windshield washer fluid warning
• Door open warning (when vehicle is

stopped)

• Low tire pressure warning
• Loose Fuel Cap warning
• Traffic Sign Recognition system fault (if so

equipped)

• Driver Attention Alert system fault (if so

equipped)

• Push Engine Start Lock warning
• Incorrect Key warning
• I-Key System Fault warning
• CVT warning
• Sonar Parking Sensor Error warning
• LED Headlight Failure warning (when no

other red warnings are on)

• Chassis Control warning
• Tire size incorrect warning
• AWD system error warning
• AWD high temperature warning

For additional information, see “Vehicle in-
formation display” (P. 2-16).

Power steering warning
light

WARNING

If the engine is not running or is
turned off while driving, the power
assist for the steering will not work.
Steering will be harder to operate.

When the power steering warning
light illuminates with the engine run-
ning, there will be no power assist for
the steering. You will still have control
of the vehicle, but the steering will be
harder to operate. Have the power
steering system checked. It is recom-
mended that you visit a NISSAN
dealer for this service.

When the ignition switch is placed in the ON
position, the power steering warning light
illuminates. After starting the engine, the
power steering warning light turns off. This
indicates the power steering is operational.

If the power steering warning light illumi-
nates while the engine is running, it may
indicate the power steering is not function-
ing properly and may need servicing. Have
the power steering checked. It is recom-
mended that you visit a NISSAN dealer for
this service.

When the power steering warning light illu-
minates with the engine running, there will
be no power assist for the steering, but you
will still have control of the vehicle. At this
time, greater steering effort is required to
operate the steering wheel, especially in
sharp turns and at low speeds.

2-14

Instruments and controls

-------------------------------------------------------------------------------------------------------------------------------------------------------------

For additional information, see “Power
steering” (P. 5-119).

Rear Automatic Braking
(RAB) system warning light

This light comes on when the ignition
switch is placed in the ON position. It turns
off after the engine is started.

This light illuminates when the RAB system
is turned off in the vehicle information
display.

If the light illuminates when the RAB sys-
tem is on, it may indicate that the system is
unavailable. For additional information, see
“Rear Automatic Braking (RAB)” (P. 5-82).

Slip indicator light

This indicator light will blink when the Ve-
hicle Dynamic Control (VDC) system is op-
erating, thus alerting the driver to the fact
that the road surface is slippery and the
vehicle is nearing its traction limits.

You may feel or hear the system working;
this is normal.

The light will blink for a few seconds after
the VDC system stops limiting wheel spin.

The

indicator light also comes on

when you place the ignition switch in the
ON position. The light will turn off after ap-
proximately 2 seconds if the system is op-
erational. If the light does not come on
have the system checked. It is recom-
mended that you visit a NISSAN dealer for
this service.

Vehicle Dynamic Control
(VDC) OFF indicator light

This indicator light comes on when the
VDC OFF switch is pushed to off. This indi-
cates the VDC system has been turned off.

Push the VDC OFF switch again or restart
the engine and the system will operate
normally. For additional information, see
“Vehicle Dynamic Control (VDC) system”
(P. 5-122).

The VDC OFF indicator light also comes on
when you place the ignition switch in the
ON position. The light will turn off after
about 2 seconds if the system is opera-
tional. If the light stays on or comes on
along with the

indicator light while

you are driving, have the VDC system
checked. It is recommended that you visit a
NISSAN dealer for this service.

While the VDC system is operating, you
might feel a slight vibration or hear the sys-
tem working when starting the vehicle or
accelerating, but this is normal.

WARNING/INDICATOR LIGHTS
(other)

For additional information, see “Vehicle in-
formation display” (P. 2-16).

Front fog light indicator
light (green) (if so
equipped)

The front fog light indicator light illumi-
nates when the front fog lights are on. For
additional

information,

see

“Fog

light

switch” (P. 2-43).

High Beam Assist indicator
light (green)

This indicator light illuminates when the
headlights come on while the headlight
switch is in the AUTO position with the high
beams selected. This indicates that the
high beam assist is operational.

For additional information, see “Headlight
and turn signal switch” (P. 2-36).

Instruments and controls

2-15

-------------------------------------------------------------------------------------------------------------------------------------------------------------

High beam indicator light
(blue)

This blue light comes on when the head-
light high beams are on and goes out when
the low beams are selected.

Side light and headlight
indicator light (green)

The side light and headlight indicator light
illuminates when the side light or headlight
position is selected. For additional informa-
tion, see “Headlight and turn signal switch”
(P. 2-36).

Turn signal/hazard
indicator lights (green)

The appropriate light flashes when the turn
signal switch is activated.

Both lights flash when the hazard switch is
turned on.

AUDIBLE REMINDERS

Brake pad wear warning

The disc brake pads have audible wear
warnings. When a disc brake pad requires
replacement, it makes a high pitched
scraping sound when the vehicle is in mo-

tion, whether or not the brake pedal is de-
pressed. Have the brakes checked as soon
as possible if the warning sound is heard.

Light reminder chime

With the ignition switch placed in the OFF
position, a chime sounds when the driver's
door is opened if the headlights or parking
lights are on.

Turn the headlight control switch off before
leaving the vehicle.

NISSAN Intelligent Key® door
buzzer (if so equipped)

The Intelligent Key door buzzer sounds if
any one of the following improper opera-
tions is found.
• The Intelligent Key is left inside the vehicle

when locking the doors.

• The Intelligent Key is taken outside the

vehicle when operating the vehicle.

When the buzzer sounds, be sure to check
both the vehicle and the Intelligent Key. For
additional information, see “NISSAN Intelli-
gent Key®” (P. 3-7).

The vehicle information display is located
to the left of the speedometer. It displays
such items as:
• Home
• Audio information
• Navigation information (if so equipped)
• Drive computer information
• Fuel economy information
• Driving aids information (if so equipped)
• Speed Limit Sign (if so equipped)
• Tire pressure information
• Indicators and warnings
• Vehicle and meter display settings

LIC3224

VEHICLE INFORMATION DISPLAY

2-16

Instruments and controls

-------------------------------------------------------------------------------------------------------------------------------------------------------------

• Cruise control status
• Odometer/twin trip odometer
• Gear position information (P, R, N, D)
• Distance To Empty and fuel indicator
• Time
• Outside Air Temperature

The display will be interrupted when a
phone call is received. Phone calls can be
answered or rejected through the steering
wheel controls.

HOW TO USE THE VEHICLE
INFORMATION DISPLAY

The vehicle information display can be
changed using the OK and
buttons located on the steering wheel.

1. OK — change or select an item in the

vehicle information display.

— scroll up or down the vehicle in-

formation menu items. If the vehicle in-
formation display is not showing a menu
with the

buttons, pressing the

will change to the previous/next audio
preset.

2.

— go back or forward

through the vehicle information menu
items or to change from one display
screen to the next (i.e. trip, TPMS, fuel
economy).

The OK and

buttons also

control audio and control panel functions in
some conditions. Most screens and menus
offer instruction prompts of the steering
switch buttons to indicate how to control the
vehicle information display. An orange cur-
sor is shown to indicate where you are in the
available menu items. A scroll bar with up
and down arrows will appear if there is more
than one page of menu items. For additional
information,

refer

to

the

separate

NissanConnect® Owner’s Manual.

LIC3778

Instruments and controls

2-17

-------------------------------------------------------------------------------------------------------------------------------------------------------------

STARTUP DISPLAY

When the vehicle in placed in the ON or ACC
position the screens that display in the ve-
hicle information display include:
• Home
• Audio
• Navigation (if so equipped)
• Drive computer
• Fuel economy
• Driving aids (if so equipped)
• Speed Limit Sign (if so equipped)
• Tire pressure information
• Warning review
• Settings

The warnings review title screen will show
how many active warnings exist, or “No
items to review” in the event that no warn-
ings are active. For additional information
on warnings and indicators, see “Vehicle
information display warnings and indica-
tors” (P. 2-25).

To control what items display in the vehicle
information display, see “Customize Dis-
play” (P. 2-20).

SETTINGS

The setting mode allows you to change the
information displayed in the vehicle infor-
mation display:
• Driver Assistance
• Customize Display
• Vehicle Settings
• Maintenance
• Clock
• TPMS Settings
• Unit / Language
• Key-Linked Settings
• Factory Reset

2-18

Instruments and controls

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Driver Assistance

The driver assistance menu allows the user to change the various driving aids.

Some menu items shown below may not be equipped on your vehicle.

Menu item

Explanation

Lane

Displays available lane options.

Lane Departure Warning

Allows user to turn the Lane Departure Warning (LDW) system on or off. For additional information, see “Lane Departure
Warning (LDW)” (P. 5-27).

Lane Departure Prevention Allows user to turn the Intelligent Lane Intervention (I-LI) on or off when the engine is running The system will reset to off af-

ter every ignition cycle. For additional information, see “Intelligent Lane Intervention (I-LI)” (P. 5-32).

Blind Spot

Allows user to turn the Blind Spot Warning (BSW) and Rear Cross Traffic Alert (RCTA) systems on or off. For additional infor-
mation, see “Blind Spot Warning (BSW)” (P. 5-38) and “Rear Cross Traffic Alert (RCTA)” (P. 5-47).

Speed Limit Sign

Allows user to turn the Speed Limit Sign recognition on or off. For additional information, see “Traffic Sign Recognition”
(P. 5-24).

Parking Aids

Displays available parking aids.

Sensor

Displays available sensor options.

ON

Front and rear sonar is on.

OFF

Front and rear sonar is off.

Front Only

Only front sonar is on.

Display

Allows user to turn the parking aids display on or off.

Volume

Allows the user to set the parking sensor volume to High/Med./Low

Range

Allows user to set the parking sensor range to Near/Mid/Far.

Emergency Brake

Displays available emergency brake options.

Front

Allows user to turn the front emergency braking system on or off. For additional information, see “Automatic Emergency
Braking (AEB) with Pedestrian Detection” (P. 5-87) and “Intelligent Forward Collision Warning (I-FCW)” (P. 5-98).

Rear

Allows user to turn the rear emergency braking system on or off. For additional information, see “Rear Automatic Braking
(RAB)” (P. 5-82)..

Driver Attention Alert

Allows user to turn the Intelligent Driver Alertness (I-DA) on or off. For additional information, see “Intelligent Driver Alertness
(I-DA)” (P. 5-111).

Timer Alert

Allows user to set or reset the timer alert. The timer alert is based on when the ignition is placed in the ON position.

Low Temperature Alert

Allows user to turn the low temperature alert on or off.

Cruise Control Alerts

Allows user to turn the cruise control alerts on or off.

Instruments and controls

2-19

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Customize Display

The customize display menu allows the user to customize the information that appears in the vehicle information display.

Some menu items shown below may not be equipped on your vehicle.

Menu item

Explanation

Main Menu Selection

Displays available main menu items to display in the vehicle information display.

Home

Allows user to turn the home screen on or off.

Audio

Allows user to turn the audio screen on or off.

Navigation

Allows user to turn the navigation screen on or off.

Drive Computer

Allows user to turn the drive computer screen on or off.

Fuel Economy

Allows user to turn the fuel economy screen on or off.

Driving Aids

Allows user to turn the driving aids screen on or off.

Speed Limit Sign

Allows user to turn the speed limit sign screen on or off.

Tire Pressures

Allows user to turn the tire pressures screen on or off.

Car Icon Color

Allows user to select the color of the vehicle shown in the vehicle information display.

ECO Info Settings

Displays the various ECO info settings.

ECO Drive Report

Select to display this report for a period of time when the ignition is turned off.

View History

Select to view the vehicle’s fuel consumption history.

Navigation Settings

Displays the various navigation settings.

Alerts

Allows user to disable the interrupt alerts for upcoming turns.

View Mode

Allows user to select the “Arrow” mode for displaying the upcoming turn or “City” mode for displaying the intersec-
tion on a map when available.

Welcome Effect

Displays the various welcome effect settings.

Gauges

Allows the user to disable the gauge pointer sweep during vehicle startup.

Animation

Allows the user to disable the welcome animation during vehicle startup.

2-20

Instruments and controls

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Vehicle Settings

The vehicle settings allow the user to change the settings for lights, wipers, locking, keys, and other vehicle settings.

Some menu items shown below may not equipped on your vehicle.

Menu item

Explanation

Rear Door Alert

Displays the available Rear Door Alert options. For additional information, see “Rear Door Alert” (P. 2-50).

OFF

When selected, no alert or horn will be active.

Horn & Alert

When selected, the alert is displayed and horn sounds.

Alert Only

When selected, only the alert is displayed.

Lighting

Displays the various lighting settings.

Accent Lighting

Allows the user to adjust the brightness of the accent lights.

Light Sensitivity

Allows the user to change when the lights illuminate based on the brightness outside the vehicle.

Light Off Delay

Allows the user to change the duration of time, from 0 to 180 seconds, that the automatic headlights stay on
after the vehicle is shut off.

Turn Indicator

Displays available turn indicator settings.

3 Flash Pass

Allows the user to turn the 3 flash pass on or off.

Locking

Displays the various locking settings.

Ext. Door Switch

Allows user to turn the exterior door switch on or off. When turned on, the request switch on the door is acti-
vated.

Selective Unlock

Allows user to turn selective unlock on and off. When turned on, the driver’s door is unlocked and the door
handle request switch on the driver’s or front passenger’s door is pushed to be unlocked, only the corre-
sponding door is unlocked first. All the doors can be unlocked if the door unlock operation is performed
again within 1 minute. When this item is turned to OFF, all the doors will be unlocked after the door unlock
operation is performed once.

Answer Back Horn

Allows user to turn answer back horn on or off. When turned on, the horn will chirp and the hazard indicators
will flash once when locking the vehicle with the Intelligent Key.

Auto Door Unlock

Displays the options for the auto door unlock.

OFF

Doors will have to be manually unlocked.

Ignition OFF

Doors will unlock when the ignition is turned off.

Instruments and controls

2-21

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Menu item

Explanation

Shift into Park

Doors will unlock when the vehicle is shifted into P (Park).

Wipers

Displays the various wipers settings.

Speed Dependent

Allows the user to turn the speed dependent feature on or off.

Driving Position

Displays the various driving position settings.

Exit Seat Slide

Allows the user to turn the exit seat slide on or off. When turned on, the driver seat will slide back after ignition
is turned off for easy exit of the vehicle. For additional information, see "Memory seat" (P. 3-37).

Exit Steering Up

Allows the user to turn the exit steering up on or off. When turned on, the steering wheel will rise after ignition
is turned off for easy exit of the vehicle. For additional information, see "Memory seat" (P. 3-37).

Remote Engine Start

Allows user to turn the Remote Engine Start on or off. When turned on, the engine can be restarted remotely.
For additional information, see “Remote Engine Start” (P. 3-18).

Maintenance

The maintenance menu allows the user to set reminders for various vehicle maintenance items.

WARNING

The tire replacement indicator is not a substitute for regular tire checks, including tire pressure checks. For additional informa-
tion, see “Changing wheels and tires” (P. 8-36). 
Many factors including tire inflation, alignment, driving habits and road conditions
affect tire wear and when tires should be replaced. Setting the tire replacement indicator for a certain driving distance does not
mean your tires will last that long. Use the tire replacement indicator as a guide only and always perform regular tire checks.
Failure to perform regular tire checks, including tire pressure checks could result in tire failure. Serious vehicle damage could
occur and may lead to a collision, which could result in serious personal injury or death.

Menu item

Explanation

Maintenance

Displays various maintenance reminder options.

Oil and Filter

Allows user to set a reminder at a specific interval or reset the current one.

Tire

Allows user to set a reminder at a specific interval or reset the current one.

Other

Allows user to set a reminder at a specific interval or reset the current one.

2-22

Instruments and controls

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Clock

Menu item

Explanation

Clock

The vehicle clock can only be adjusted from the audio center display. When selected, the user will be in-
structed to go to the settings menu in the audio center display. For additional information, refer to the sepa-
rate NissanConnect® Owner's Manual.

TPMS Settings

The TPMS settings menu allows the user to change the tire pressure units displayed in the vehicle information display.

Menu item

Explanation

Tire Pressure Unit

Allows the user to select the tire pressure units that will display in the vehicle information display.

Unit/Language

The Unit/Language menu allows the user to change the units and language shown in the vehicle information display.

Menu item

Explanation

Mileage/Fuel

Allows user to select different mileage display units.

Tire Pressure Unit

Allows user to select different pressure display units.

Temperature

Allows user to select different temperature display units.

Language

Allows user to select different languages.

Instruments and controls

2-23

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Key-Linked Settings

Menu item

Explanation

System

Allows user to turn the Key-Linked Settings on or off. For additional information, see "Memory seat" (P. 3-37).

Factory Reset

The factory reset menu allows the user to restore the vehicle information display settings to factory status.

Menu item

Explanation

Factory Reset

Allows user to reset the vehicle information display settings to the original factory settings. Once selected,
the user can confirm or cancel the reset.

2-24

Instruments and controls

-------------------------------------------------------------------------------------------------------------------------------------------------------------

VEHICLE INFORMATION DISPLAY
WARNINGS AND INDICATORS

The following messages may appear in
your vehicle information display.

Engine start operation for
Intelligent Key system (if
I-Key battery level is low)

This indicator appears when the battery of
the Intelligent Key is low and when the In-
telligent Key system and the vehicle are not
communicating normally.

If this appears, touch the ignition switch
with the Intelligent Key while depressing
the brake pedal. For additional information,
see “NISSAN Intelligent Key® battery dis-
charge” (P. 5-15).

Key Battery Low

This indicator appears when the Intelligent
Key battery is running out of power.

If this indicator appears, replace the bat-
tery with a new one. For additional infor-
mation, see “Battery replacement” (P. 8-22).

Key ID Incorrect

This warning appears when the ignition
switch is placed from the OFF position and
the Intelligent Key is not recognized by the
system. You cannot start the engine with
an unregistered key.

For additional information, see “NISSAN In-
telligent Key®” (P. 3-7).

Key System Fault See
Owner’s Manual

After the ignition switch is placed in the ON
position, this warning appears for a period
of time and then turns off.

The Key System Fault message warns of a
malfunction with the Intelligent Key sys-
tem. If the warning appears while the en-
gine is stopped, it may be impossible to
start the engine.

If the warning appears while the engine is
running, you can drive the vehicle. However,
in these cases, have the system checked. It
is recommended that you visit a NISSAN
dealer for this service.

No Key Detected

This warning appears when the Intelligent
Key is left outside the vehicle with the igni-
tion switch in the ON position. Make sure
the Intelligent Key is inside the vehicle.

For additional information, see “NISSAN In-
telligent Key®” (P. 3-7).

Brightness indicator

This indicator shows the brightness ad-
justment of the instrument panel. For addi-
tional information, see “Instrument bright-
ness control” (P. 2-42).

Check Rear Seat For All Articles

When the system is enabled, this message
appears when the vehicle comes to a com-
plete stop, the vehicle is transitioned from
the D (Drive) position to P (Park) position,
and the driver exits the vehicle. This mes-
sage alerts the driver, after a period of time,
to check for items in the rear seats after
the audible alert has been provided.

Instruments and controls

2-25

-------------------------------------------------------------------------------------------------------------------------------------------------------------

NOTE:

This system is disabled until a driver en-
ables it using the vehicle information
display. For additional information, see
“How to use the vehicle information dis-
play” (P. 2-17).

For additional information, see “Rear Door
Alert” (P. 2-50).

Rear Door Alert is activated

When the system is enabled, this message
appears when the Rear Door Alert system
is active and can remind the driver to check
the back seat.
• Using the steering wheel switch, a driver

can select “Dismiss Message” to clear the
display for a period of time. If no selection
is made, this message automatically
turns off after a period of time.

• Using the steering wheel switch, a driver

can select “Disable Alert” to disable the
horn alert for the remainder of the cur-
rent trip.

WARNING

Selecting “Dismiss Message” during a
stop within a trip temporarily dis-
misses the message for that stop with-
out turning the system off. Alerts can
be provided for other stops during the
trip. Selecting “Disable Alert” turns off
the Rear Door Alert system for the re-
mainder of a trip and no audible alert
will be provided.

NOTE:

This system is disabled until a driver en-
ables it using the vehicle information
display. For additional information, see
“How to use the vehicle information dis-
play” (P. 2-17).

For additional information, see “Rear Door
Alert” (P. 2-50).

Door/liftgate Open

This warning appears when a door or the
liftgate has been opened.

Headlight System Error: See Owner’s
Manual

This warning appears when the LED head-
lights are not functioning properly.

If this warning appears, have your system
checked. It is recommended that you visit a
NISSAN dealer for this service.

Loose Fuel Cap

This warning appears when the fuel-filler
cap is not tightened correctly after the ve-
hicle has been refueled. For additional in-
formation, see “Fuel-filler cap” (P. 3-29).

Low Fuel

This warning appears when the fuel level in
the fuel tank is getting low. Refuel as soon
as it is convenient, preferably before the
fuel gauge reaches 0 (Empty).

There will be

a small reserve of fuel in the tank when
the fuel gauge needle reaches 0 (Empty).

Low Outside Temperature

This warning appears if the outside tem-
perature is below 37°F (3°C). The tempera-
ture can be changed to display in Celsius or
Fahrenheit. For additional information, see
“Settings” (P. 2-18).

2-26

Instruments and controls

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Low Washer Fluid

This

warning

appears

when

the

windshield-washer fluid is at a low level.
Add windshield-washer fluid as necessary.
For

additional

information,

see

“Windshield-washer fluid” (P. 8-12).

Power will turn off to save the battery

This message appears in the vehicle infor-
mation display after a period of time if the
ignition switch is in the ACC or the ON po-
sition and if the vehicle is in P (Park). For
additional information, see “Push-button
ignition switch positions” (P. 5-13).

Power turned off to save the battery

This message appears after the ignition
switch is automatically turned to off. For
additional information, see “Push-button
ignition switch positions” (P. 5-13)

Push brake and start
switch to drive

This indicator appears when the shift lever
is in the P (Park) position.

This indicator also appears when the ve-
hicle has been started using the Remote
Engine Start (if so equipped) function.

This indicator means that the engine will
start by pushing the ignition switch with
the brake pedal depressed. You can start
the engine from any position of the ignition
switch.

Release Parking Brake

This warning appears in the message area
of the vehicle information display when the
parking brake is set and the vehicle is
driven.

Reminder: Turn OFF
Headlights

This warning appears when the headlights
are left in the ON position when exiting the
vehicle. Place the headlight switch in the
OFF or AUTO position. For additional infor-
mation, see “Headlight and turn signal
switch” (P. 2-36).

Shift to Park

This warning appears when the ignition
switch is in the ACC or OFF position and the
shift lever is not in the P (Park) position. Also,
a chime sounds when the ignition switch is
in the ACC or OFF position.

If this warning appears, move the shift lever
to the P (Park) position or start the engine.

Shipping Mode On Push Storage Fuse

This warning may appear if the extended
storage switch is not pushed in. When this
warning appears, push in the extended
storage switch to turn off the warning. For
additional information, see “Extended stor-
age switch” (P. 2-52).

Tire Pressure Low - Add Air

This warning appears when the low tire
pressure warning light in the meter illumi-
nates and low tire pressure is detected. The
warning appears each time the ignition
switch is placed in the ON position as long
as the low tire pressure warning light re-
mains illuminated. If this warning appears,
stop the vehicle and adjust the tire pres-
sures of all four tires to the recommended
COLD tire pressure shown on the Tire and
Loading Information label. For additional
information, see “Low tire pressure warning
light” (P. 2-11) and “Tire Pressure Monitoring
System (TPMS)” (P. 5-5).

Transmission Shift Position
indicator

This indicator shows the transmission shift
position.

Instruments and controls

2-27

-------------------------------------------------------------------------------------------------------------------------------------------------------------

AWD Error: See Owner’s
Manual

This warning appears when the all-wheel
drive system is not functioning properly
while the engine is running.

AWD High Temp. Stop
Vehicle

This warning may appear while trying to
free a stuck vehicle due to increased oil
temperature.

The

driving

mode

may

change to 2-Wheel Drive (2WD). If this
warning is displayed, stop the vehicle with
the engine idling, as soon as it is safe to do
so. Then if the warning turns off, you can
continue driving.

Tire Size Incorrect: See
Owner’s Manual

This warning may appear if there is a large
difference between the diameters of the
front and rear wheels. Pull off the road in a
safe area, with the engine idling. Check that
all the tire sizes are the same, that the tire
pressure is correct and that the tires are
not excessively worn.

CVT Error: See Owner's
Manual

This warning appears when the there is a
problem with the CVT system. If this
warning

appears,

have

the

system

checked. It is recommended that you visit a
NISSAN dealer for this service.

Alarm - Time for a break?

This indicator appears when the driver en-
ables the timer alert function within the
driver assistance settings and the selected
set time is expired. The time is based on
ignition on time and can be set up to six
hours.

Automatic Emergency
Braking (AEB) with
Pedestrian Detection
emergency warning
indicator

This indicator appears along with an au-
dible warning, when the system detects
the possibility of a forward collision.

For additional information, see “Automatic
Emergency Braking (AEB) with Pedestrian
Detection” (P. 5-87).

Blind Spot Warning (BSW)
and Rear Cross Traffic Alert
(RCTA) indicator

This indicator appears when the BSW and
RCTA systems are engaged.

For additional information, see “Blind Spot
Warning (BSW)” (P. 5-38) and “Rear Cross
Traffic Alert (RCTA)” (P. 5-47).

Cruise control indicator

These indicators show the cruise control
system status.

For additional information, see “Cruise con-
trol” (P. 5-55).

Cruise ON

This message appears if the

cruise

control switch on the steering wheel is
pressed and Cruise Control Alerts are en-
abled in the vehicle information display.

For additional information, see “Cruise con-
trol” (P. 5-55).

Cruise Target Speed SET

This message will appear if the Cruise Con-
trol system is on when the SET switch is
pushed and the Cruise Control Alerts are
enabled.

2-28

Instruments and controls

-------------------------------------------------------------------------------------------------------------------------------------------------------------

 

 

 

 

 

 

 

Content      ..     5      6      7      8     ..